scholarly journals Influence of silicon carbide mixed used engine oil dielectric fluid on EDM characteristics of AA7075/SiCp/B4Cp hybrid composites

2021 ◽  
Author(s):  
Ganapathy Iyyapan ◽  
R. Sudhakara Pandian ◽  
M. Sakthivel
Keyword(s):  
Silicon Carbide ◽  
Hybrid Composites ◽  
Engine Oil ◽  
Dielectric Fluid ◽  
Used Engine Oil

Effect of Powder-Mixed Dielectric on EDM Process Performance

2020 ◽  
Vol 38 (8A) ◽  
pp. 1226-1235
Author(s):  
Safa R. Fadhil ◽  
Shukry. H. Aghdeab
Keyword(s):  
Silicon Carbide ◽  
High Speed ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
High Speed Steel ◽  
Transformer Oil ◽  
Dielectric Fluid ◽  
Peak Current ◽  
Powder Concentration ◽  
Pulse On Time

Electrical Discharge Machining (EDM) is extensively used to manufacture different conductive materials, including difficult to machine materials with intricate profiles. Powder Mixed Electro-Discharge Machining (PMEDM) is a modern innovation in promoting the capabilities of conventional EDM. In this process, suitable materials in fine powder form are mixed in the dielectric fluid. An equal percentage of graphite and silicon carbide powders have been mixed together with the transformer oil and used as the dielectric media in this work. The aim of this study is to investigate the effect of some process parameters such as peak current, pulse-on time, and powder concentration of machining High-speed steel (HSS)/(M2) on the material removal rate (MRR), tool wear rate (TWR) and the surface roughness (Ra). Experiments have been designed and analyzed using Response Surface Methodology (RSM) approach by adopting a face-centered central composite design (FCCD). It is found that added graphite-silicon carbide mixing powder to the dielectric fluid enhanced the MRR and Ra as well as reduced the TWR at various conditions. Maximum MRR was (0.492 g/min) obtained at a peak current of (24 A), pulse on (100 µs), and powder concentration (10 g/l), minimum TWR was (0.00126 g/min) at (10 A, 100 µs, and 10 g/l), and better Ra was (3.51 µm) at (10 A, 50 µs, and 10 g/l).

Effect of graphite and silicon carbide fillers on mechanical properties of PA6 polymer composites

2017 ◽  
Vol 37 (6) ◽  
pp. 547-557 ◽  
Author(s):  
Sekaran Sathees Kumar ◽  
Ganesan Kanagaraj
Keyword(s):  
Mechanical Properties ◽  
Silicon Carbide ◽  
Polymer Composites ◽  
Interfacial Adhesion ◽  
Hybrid Composites ◽  
Fracture Morphology ◽  
Tensile Fracture ◽  
Injection Molded ◽  
The Individual

Abstract In this paper, the combined effect of different weight percentages of silicon carbide (SiC) and graphite (Gr) reinforcement on the mechanical properties of polyamide (PA6) composite is studied. Test specimens of pure PA6, 85 wt% PA6+10 wt% SiC+5 wt% Gr and 85 wt% PA6+5 wt% SiC+10 wt% Gr are prepared using an injection molding machine. The tensile, impact, hardness, morphology and thermal properties of the injection molded composites were investigated. The obtained results showed that mechanical properties, such as tensile and impact strength and modulus of the PA6 composites, were significantly higher than the pure PA6, and hybridization with silicon carbide and graphite further enhanced the performance properties, as well as the thermal resistance of the composites. The tensile fracture morphology and the characterization of PA6 polymer composites were observed by scanning electron microscope (SEM) and Fourier transform infrared spectroscopic methods. SEM observation of the fracture surfaces showed the fine dispersion of SiC and Gr for strong interfacial adhesion between fibers and matrix. The individual and combined reinforcing effects of silicon carbide and graphite on the mechanical properties of PA6 hybrid composites were compared and interpreted in this study. Improved mechanical properties were observed by the addition of small amount of SiC and Gr concurrently reinforced with the pure PA6. Finally, thermogravimetric analysis showed that the heat resistance of the composites tended to increase with increasing silicon carbide and graphite content simultaneously.

scholarly journals Utilización de aceite quemado y paraquat en la desecación de soya y sus efectos en la calidad de la semilla durante el almacenamiento

2016 ◽  
Vol 3 ◽  
pp. 61
Author(s):  
R. Ibañez
Keyword(s):  
Environmental Conditions ◽  
Seed Quality ◽  
Rio Grande ◽  
Engine Oil ◽  
Soybean Seeds ◽  
Harvest Time ◽  
Rio Grande Do Sul ◽  
Used Engine Oil ◽  
Soybean Plants ◽  
Germination Vigor

The assay was conducted in Pelotas, Rio Grande do Sul-Brasil, to compare the effect of used engine oil with to paraquat (Gramoxone) applied during the physiological maturition of soybean seeds (Glicyne max (L.) Merrill), Bragg variety. The oil doses were 5.3, 8.5 and 12 l/ha. The desiccation intensity was determined and 30 pods per plot were periodically collected to follow the humidity content of the seeds, to 18%. The humidity was later reduced to 10.5 +0.5 and 2.0 kg of seeds were stored, in cotton bags,during 6 months under the environmental conditions at the Centro de Entrenamiento de Semillas of the Federal University of Pelotas. The seeds were subjected to germination, vigor and phytosanitary tests at harvest time and after 3 and 6 months of storage. Under the conditions of this trial, the doses of 12 l/ha of oil and 2 l/ha of paraquat: a) act as desiccants for soybean plants, b) favors the production of seeds with better viability and vigor after 6 months of storage and c) guarantied better sanitary seed quality after 6 months of storage.

Sign in / Sign up

Export Citation Format

Share Document