scholarly journals A lattice Boltzmann simulation of oblique impact of a single rain droplet on super-hydrophobic surface with randomly distributed rough structures

2020 ◽  
Vol 15 (3) ◽  
pp. 443-449
Author(s):  
Zhang Shusheng ◽  
Lu Hao ◽  
Zhang Li-Zhi ◽  
Riffat Saffa ◽  
Ure Zafer ◽  
...  
Keyword(s):  
Lattice Boltzmann ◽  
Contact Time ◽  
Hydrophobic Surface ◽  
Impact Angle ◽  
Oblique Impact ◽  
Building Structures ◽  
Pinning Effect ◽  
Lattice Boltzmann Simulation ◽  
Boltzmann Method ◽  
The Impact

Abstract In this paper, oblique impact of a single rain droplet on super-hydrophobic surface with randomly distributed rough structures was investigated by lattice Boltzmann method. The effects of the impact angle of the droplet as well as the skewness and kurtosis of rough surface on the bouncing ability of the droplet were in this paper. It was found that the oblique impact can effectively reduce the contact time in the process of droplet bouncing off, because the energy consumption caused by the pinning effect is reduced. Moreover, the contact time most possibly reaches the shortest when the impact angle is 45°. Decreasing the skewness and keeping the kurtosis around 4.0 can enhance the bouncing ability during the droplet oblique impact on randomly distributed rough surfaces. The results are useful for the design of building structures.

scholarly journals Waterfall Algorithm as a tool of investigation the geometrical features of granular porous media

2021 ◽  
Author(s):  
Wojciech Sobieski
Keyword(s):  
Particle Size ◽  
Porous Media ◽  
Lattice Boltzmann ◽  
Granular Media ◽  
Density Ratio ◽  
Geometrical Features ◽  
Granular Porous Media ◽  
Collision Density ◽  
Boltzmann Method ◽  
The Impact

AbstractThe paper describes the so-called Waterfall Algorithm, which may be used to calculate a set of parameters characterising the spatial structure of granular porous media, such as shift ratio, collision density ratio, consolidation ratio, path length and minimum tortuosity. The study is performed for 1800 different two-dimensional random pore structures. In each geometry, 100 individual paths are calculated. The impact of porosity and the particle size on the above-mentioned parameters is investigated. It was stated in the paper, that the minimum tortuosity calculated by the Waterfall Algorithm cannot be used directly as a representative tortuosity of pore channels in the Kozeny or the Carman meaning. However, it may be used indirect by making the assumption that a unambiguous relationship between the representative tortuosity and the minimum tortuosity exists. It was also stated, that the new parameters defined in the present study are sensitive on the porosity and the particle size and may be therefore applied as indicators of the geometry structure of granular media. The Waterfall Algorithm is compared with other methods of determining the tortuosity: A-Star Algorithm, Path Searching Algorithm, Random Walk technique, Path Tracking Method and the methodology of calculating the hydraulic tortuosity based on the Lattice Boltzmann Method. A very short calculation time is the main advantage of the Waterfall Algorithm, what meant, that it may be applied in a very large granular porous media.

scholarly journals Lattice Boltzmann Simulation of Natural Convection in an Annulus between a Hexagonal Cylinder and a Square Enclosure

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
L. El Moutaouakil ◽  
Z. Zrikem ◽  
A. Abdelbaki
Keyword(s):  
Natural Convection ◽  
Rayleigh Number ◽  
Cross Section ◽  
Lattice Boltzmann ◽  
Square Enclosure ◽  
Lattice Boltzmann Simulation ◽  
Laminar Natural Convection ◽  
Heat Transfers ◽  
Boltzmann Method ◽  
Vertical Case

Laminar natural convection in a water filled square enclosure containing at its center a horizontal hexagonal cylinder is studied by the lattice Boltzmann method. The hexagonal cylinder is heated while the walls of the cavity are maintained at the same cold temperature. Two orientations are treated, corresponding to two opposite sides of the hexagonal cross-section which are horizontal (case I) or vertical (case II). For each case, the results are presented in terms of streamlines, isotherms, local and average convective heat transfers as a function of the dimensionless size of the hexagonal cylinder cross-section (0.1≤B≤0.4), and the Rayleigh number (103≤Ra≤106).

scholarly journals Lattice Boltzmann simulation of two-sided lid-driven flow in deep cavities

2015 ◽  
pp. 157-168
Author(s):  
Natasa Lukic ◽  
Predrag Tekic ◽  
Jelena Radjenovic ◽  
Ivana Sijacki
Keyword(s):  
Aspect Ratio ◽  
Flow Pattern ◽  
Lattice Boltzmann ◽  
Reynolds Numbers ◽  
Critical Aspect ◽  
Symmetric Flow ◽  
Primary Vortex ◽  
Lattice Boltzmann Simulation ◽  
Boltzmann Method ◽  
Deep Cavities

The present study is concerned with two-sided lid-driven incompressible flow in rectangular, deep cavities applying lattice Boltzmann method. After validating the code for the square cavity, solutions for cavities with an aspect ratio 1.5 and 4 were obtained for the Reynolds numbers of 100, 400, 1000 and 3200. The influence of the Reynolds number and aspect ratio on the flow pattern and on the characteristics of vortices inside the cavity was studied. Symmetric flow pattern was obtained for all investigated cases. The middle of the cavity is mostly influenced by the increase in the aspect ratio. Critical aspect ratio, at which the birth of a primary vortex in the middle of the cavity takes place, was determined to be between 2.7 and 2.725.

scholarly journals Lattice Boltzmann simulation of liquid falling on horizontal rectangular pillar arrays

2021 ◽  
Vol 321 ◽  
pp. 01014
Author(s):  
Makoto Sugimoto ◽  
Tatsuya Miyazaki ◽  
Zelin Li ◽  
Masayuki Kaneda ◽  
Kazuhiko Suga
Keyword(s):  
Lattice Boltzmann ◽  
Three Dimensional ◽  
Phase Field Model ◽  
Flow Simulation ◽  
High Viscosity ◽  
Two Phase ◽  
Lattice Boltzmann Simulation ◽  
Pillar Arrays ◽  
Boltzmann Method ◽  
Behavior Characteristic

Stator coils of automobiles in operation generate heat and are cooled by a coolant poured from above. Since the behavior characteristic of the coolant poured on the coils is not clarified yet due to its complexity, the three-dimensional two-phase flow simulation is conducted. In this study, as a steppingstone to the simulation of the liquid falling on the actual coils, the coils are modelled with horizontal rectangular pillar arrays whose governing parameters can be easily changed. The two-phase flows are simulated using the lattice Boltzmann method and the phase-field model, and the effects of the governing parameters, such as the physical properties of the cooling liquid, the wettability, and the gap between the pillars, on the wetting area are investigated. The results show that the oil tends to spread across the pillars because of its high viscosity. Moreover, the liquid spreads quickly when the contact angle is small. In the case that the pillars are stacked, the wetting area of the inner pillars is larger than that of the exposed pillars.

scholarly journals Study on droplet nucleation position and jumping on structured hydrophobic surface using the lattice Boltzmann method

2021 ◽  
pp. 149-149
Author(s):  
Gaojie Liang ◽  
Lijun Liu ◽  
Haiqian Zhao ◽  
Cong Li ◽  
Nandi Zhang
Keyword(s):  
Lattice Boltzmann Method ◽  
Significant Influence ◽  
Lattice Boltzmann ◽  
Hydrophobic Surface ◽  
Numerical Results ◽  
Nucleation Mode ◽  
Droplet Nucleation ◽  
Simulation Results ◽  
The Individual ◽  
Boltzmann Method

In this study, droplet nucleation and jumping on the conical microstructure surface is simulated using the Lattice Boltzmann Method (LBM). The nucleation and jumping laws of the droplet on the surface are summarized. The numerical results suggest that the height and the gap of the conical microstructure exhibit a significant influence on the nucleation position of the droplet. When the ratio of height to the gap of the microstructure(H/D) is small, the droplet tends to nucleate at the bottom of the structure. Otherwise, the droplet tends to nucleate towards the side of the structure. The droplet grown in the side nucleation mode possesses better hydrophobicity than that of the droplet grown in the bottom nucleation mode and the droplet jumping becomes easier. Apart from the coalescence of the droplets jumping out of the surface, jumping of individual droplets may also occur under certain conditions. The ratio of the clearance to the width of the conical microstructure(D/F) depends on the jumping mode of the droplet. The simulation results indicate that when the D/F ratio is greater than 1.2, the coalescence jump of droplets is likely to occur. On the contrary, the individual jump of droplets is easy to occur.

Modeling of collapsing cavitation bubble near solid wall by 3D pseudopotential multi-relaxation-time lattice Boltzmann method

2017 ◽  
Vol 232 (3) ◽  
pp. 445-456 ◽  
Author(s):  
Minglei Shan ◽  
Yu Yang ◽  
Hao Peng ◽  
Qingbang Han ◽  
Changping Zhu
Keyword(s):  
Relaxation Time ◽  
Lattice Boltzmann ◽  
Cavitation Bubble ◽  
Solid Wall ◽  
Three Dimensional ◽  
Lattice Boltzmann Model ◽  
Bubble Collapse ◽  
Lattice Boltzmann Simulation ◽  
Boltzmann Method ◽  
Boltzmann Model

Understanding the dynamic characteristic of the cavitation bubble near a solid wall is a fundamental issue for the bubble collapse application and prevention. In the present work, an improved three-dimensional multi-relaxation-time pseudopotential lattice Boltzmann model is adopted to investigate the cavitation bubble collapse near the solid wall. With respect to thermodynamic consistency, Laplace law verification, the three-dimensional pseudopotential multi-relaxation-time lattice Boltzmann model is investigated. By the theoretical analysis, it is proved that the model can be regarded as a solver of the Rayleigh–Plesset equation, and confirmed by comparing the results of the lattice Boltzmann simulation and the Rayleigh–Plesset equation calculation for the case of cavitation bubble collapse in the infinite medium field. The bubble collapse near the solid wall is modeled using the improved pseudopotential multi-relaxation-time lattice Boltzmann model. We find the lattice Boltzmann simulation and the experimental results have the same dynamic process by comparing the bubble profiles evolution. Form the pressure field and the velocity field evolution it is found that the tapered higher pressure region formed near the top of the bubble is a crucial driving force inducing the bubble collapse. This exploratory research demonstrates that the lattice Boltzmann method is an alternative tool for the study of the interaction between collapsing cavitation bubble and matter.

The Impact of the Conical Indenter on a Plate Laying on a Winkler Foundation

2018 ◽  
Vol 931 ◽  
pp. 84-90 ◽  
Author(s):  
Aleksey N. Beskopylny ◽  
Andrey A. Veremeenko ◽  
Elena E. Kadomtseva ◽  
Natalia I. Beskopylnaia
Keyword(s):  
Contact Time ◽  
Mechanical Characteristics ◽  
Strength Characteristics ◽  
Winkler Foundation ◽  
Building Structures ◽  
Dynamic Impact ◽  
Conical Indenter ◽  
Elastic Plastic ◽  
Plastic Indentation ◽  
The Impact

In the practice of civil engineering, the methods of impact diagnostics of materials find their application, allowing quickly and accurately measure the required strength characteristics at any point in the structure. Impact methods offer many advantages, for example, at smaller dimensions can be developed big the contact force, it can be recorded more information about the response of the material to dynamic impact and others. This approach is widely used in determining the hardness of materials and makes it possible to determine the complex mechanical characteristics: yield strength, ultimate strength, and elongation. In the paper we consider the axisymmetric problem of the impact of the conical indenter on the plate, laying on Winkler Foundation under elastic-plastic deformation. The solution is based on the phenomenological model of elastic-plastic indentation in a quasistatic formulation. The general deformations of the plate are considered elastic, and the local, in the contact zone, are elastoplastic. The main characteristics of the impact are determined: the force of the contact interaction, the local indentation, the contact time. The device and methods of determining the strength characteristics of plates under specified conditions of impact were developed on the basis of obtained solutions. The proposed method has been tested on many building structures: bridges, trusses, structural structures of artificial structures, reinforcement bars, welded joints.

Simulation of Heat Transfer With LBM and Lagrangian Methods for Microfluidic Applications

2005 ◽  
Author(s):  
Nishitha Thummala ◽  
Dimitrios V. Papavassiliou
Keyword(s):  
Heat Transfer ◽  
Flow Field ◽  
Lattice Boltzmann ◽  
Constant Heat Flux ◽  
Fully Developed Flow ◽  
Thermal Boundary Conditions ◽  
Lattice Boltzmann Simulation ◽  
Lagrangian Tracking ◽  
Boltzmann Method ◽  
Single Flow

This work presents a Lagrangian approach to simulate convective heat transfer in small scales. The fully developed flow field, simulated by a Lattice Boltzmann Method, is combined with Lagrangian tracking of thermal markers to determine the behavior of an instantaneous scalar line source located at the wall of a channel. The resulting probability density functions are used to calculate the behavior of continuous line sources of heat at the wall of the channel, as well as the temperature for the case of constant temperature or constant heat flux from the wall. This method is resourceful in terms of computational efficiency, in that it can be used to simulate various thermal boundary conditions and Prandtl number fluids with a single flow field resulting from a Lattice Boltzmann simulation.

Evaluation of Local Damage to Reinforced Concrete Panels Subjected to Oblique Impact of Rigid and Soft Missiles

2018 ◽  
Author(s):  
Akemi Nishida ◽  
Minoru Nagai ◽  
Haruji Tsubota ◽  
Yinsheng Li
Keyword(s):  
Reinforced Concrete ◽  
Simulation Method ◽  
Impact Angle ◽  
Oblique Impact ◽  
Local Damage ◽  
Empirical Formulas ◽  
Rc Structures ◽  
Impact Tests ◽  
Oblique Impacts ◽  
The Impact

Many empirical formulas have been proposed for evaluating local damage to reinforced concrete (RC) structures caused by impacts of rigid missiles. Most of these formulas have been derived based on impact tests normal to the target structures. Up to now, few impact tests oblique to the target structures have been carried out. This study has been conducted with the purpose of proposing a new formula for evaluating the local damage caused by oblique impacts based on previous experimental and simulation results. In this paper, the results of simulation analyses for evaluating the local damage to a RC panel subjected to normal and oblique impacts by rigid and soft missiles, by using the simulation method that was validated using the results of previous impact experiments. Based on the results of these simulation analyses, the effects of the rigidity of the missile as well as the impact angle on the local damage to the target structures are clarified.

Lattice Boltzmann Simulation of Flow and Heat Transfer Characteristics in a Symmetrically Bifurcated Microchannel

2004 ◽  
Author(s):  
Keqiang Xing ◽  
Yong Tao
Keyword(s):  
Heat Transfer ◽  
Lattice Boltzmann ◽  
Constant Heat Flux ◽  
Lattice Boltzmann Model ◽  
Straight Tube ◽  
Lattice Boltzmann Simulation ◽  
Flux Boundary Conditions ◽  
Boltzmann Method ◽  
Thermal Lattice Boltzmann ◽  
Transfer Problems

The lattice Boltzmann method (LBM) as a relatively new numerical scheme has recently achieved considerable success in simulating fluid flows and associated transport phenomena. However, application of this method to heat transfer problems has been at a stage of infancy. In this work, a thermal lattice Boltzmann model is employed to simulate a two-dimensional, steady flow in a symmetric bifurcation under constant temperature and constant heat flux boundary conditions. The bifurcation effects on the heat transfer and fluid flow are investigated and comparisons are made with the straight tube. Also, different bifurcation angles are simulated and the results are compared with the work of the other researchers.

Sign in / Sign up

Export Citation Format

Share Document