Dynamic stall of an airfoil with different mounting angle of gurney flap

2020 ◽  
Vol 92 (7) ◽  
pp. 1037-1048
Author(s):  
Mehran Masdari ◽  
Milad Mousavi ◽  
Mojtaba Tahani
Keyword(s):  
Lift Coefficient ◽  
Oscillation Amplitude ◽  
Vertical Axis ◽  
Aerodynamic Performance ◽  
Dynamic Stall ◽  
Content Type ◽  
Naca0012 Airfoil ◽  
Gurney Flap ◽  
Stall Angle ◽  
Axis Length

Purpose One of the best methods to improve wind turbine aerodynamic performance is modification of the blade’s airfoil. The purpose of this paper is to investigate the effects of gurney flap geometry and its oscillation parameters on the pitching NACA0012 airfoil. Design/methodology/approach This numerical solution has been carried out for different cases of gurney flap mounting angles, heights, reduced frequencies and oscillation amplitudes, then the results were compared to each other. The finite volume method was used for the discretization of the governing equations, and the PISO algorithm was used to solve the equations. Also, the “SST” was adopted as the turbulence model in the simulation. Findings In this paper, the different parameters of gurney flap were investigated. The results showed that the best range of gurney flap height are between 1 and 3.2% of chord and the best ratio of lifting to drag coefficient is achieved in gurney flap with an angle of 90° relative to the chord direction. The dynamic stall angle of the airfoil with gurney flap decreases were compared to without gurney flap. Earlier LEV formation can be one of the main reasons for decreasing the dynamic stall angle of the airfoil with gurney flap. Increasing the reduced frequency and oscillation amplitude causes rising of maximum lift coefficient and consequently lift curve slope. Moreover, gurney flap with mounting angle has a lower hinge moment than the gurney flap without mounting angle but with the same vertical axis length. So, there is more complexity in structural design concerning the gurney flap without mounting angle. Practical implications Improving aerodynamic efficiency of airfoils is vital for obtaining more output power in VAWTs. Gurney flaps are one of the best mechanisms to increase the aerodynamic performance of the airfoil and increases the efficiency of VAWTs. Originality/value Investigating the hinge moment on the connection point of the airfoil, gurney flap and try to compare the gurney flap with and without angle.

Dynamic Stall Simulation of Flow Over NACA0012 Airfoil at 1 Million Reynolds Number

2015 ◽  
Author(s):  
Venkata Ravishankar Kasibhotla ◽  
Danesh Tafti
Keyword(s):  
Reynolds Number ◽  
Flow Field ◽  
Lift Coefficient ◽  
Three Dimensional ◽  
Dynamic Stall ◽  
Sharp Drop ◽  
Airfoil Surface ◽  
Naca0012 Airfoil ◽  
Reduced Frequency ◽  
Edge Vortex

The paper is concerned with the prediction and analysis of dynamic stall of flow past a pitching NACA0012 airfoil at 1 million Reynolds number based on the chord length of the airfoil and at reduced frequency of 0.25 in a three dimensional flow field. The turbulence in the flow field is resolved using large eddy simulations with the dynamic Smagorinsky model at the sub grid scale. The development of dynamic stall vortex, shedding and reattachment as predicted by the present study are discussed in detail. This study has shown that the downstroke phase of the pitching motion is strongly three dimensional and is highly complex, whereas the flow is practically two dimensional during the upstroke. The lift coefficient agrees well with the measurements during the upstroke. However, there are differences during the downstroke. The computed lift coefficient undergoes a sharp drop during the start of the downstroke as the convected leading edge vortex moves away from the airfoil surface. This is followed by a recovery of the lift coefficient with the formation of a secondary trailing edge vortex. While these dynamics are clearly reflected in the predicted lift coefficient, the experimental evolution of lift during the downstroke maintains a fairly smooth and monotonic decrease in the lift coefficient with no lift recovery. The simulations also show that the reattachment process of the stalled airfoil is completed before the start of the upstroke in the subsequent cycle due to the high reduced frequency of the pitching cycle.

scholarly journals Double multiple stream tube theory coupled with dynamic stall and wake correction for aerodynamic investigation of vertical axis wind turbine

2020 ◽  
Vol 23 (4) ◽  
pp. 771-780
Author(s):  
Anh Ngoc VU ◽  
Ngoc Son Pham
Keyword(s):  
Wind Turbine ◽  
Shape Function ◽  
Vertical Axis ◽  
Transformation Method ◽  
Aerodynamic Performance ◽  
Dynamic Stall ◽  
Power Coefficient ◽  
Vertical Axis Wind Turbine ◽  
Stream Tube ◽  
Aerodynamic Investigation

This study describes an effectively analytic methodology to investigate the aerodynamic performance of H vertical axis wind turbine (H-VAWT). An in-house code based on double multiple stream tube theory (DMST) coupled with dynamic stall and wake correction is implemented to estimate the power coefficient. Design optimization of airfoil shape is conducted to study the influences of the dynamic stall and turbulent wakes. Airfoil shape is universally investigated by using the Class/Shape function transformation method. The airfoil study shows that the upper curve tends to be less convex than the lower curve in order to extract more energy of the wind upstream and generate less drag of the blade downstream. The optimal results show that the power coefficient increases by 6.5% with the new airfoil shape.

Experimental analysis of cell pattern on grid fin aerodynamics in subsonic flow

2019 ◽  
Vol 234 (3) ◽  
pp. 537-562
Author(s):  
Manish Tripathi ◽  
Mahesh M Sucheendran ◽  
Ajay Misra
Keyword(s):  
Subsonic Flow ◽  
Lift Coefficient ◽  
Aerodynamic Performance ◽  
Aerodynamic Efficiency ◽  
Grid Fin ◽  
Stall Angle ◽  
The Individual ◽  
The Impact ◽  
Control Surfaces

Grid fins consisting of a lattice of high aspect ratio planar members encompassed by an outer frame are unconventional control surfaces used on numerous missiles and bombs due to their enhanced lifting characteristics at high angles of attack and across wider Mach number regimes. The current paper accomplishes and compares the effect of different grid fin patterns on subsonic flow aerodynamics of grid fins by virtue of the determination of their respective aerodynamic forces. Furthermore, this study deliberates the impact of gap variation on aerodynamics of different patterns. Results enunciate enhanced aerodynamic efficiency, and lift slope for web-fin cells and single diamond patterns compared to the baseline model. Moreover, the study indicates improved aerodynamic performance for diamond patterns with higher gaps by providing elevated maximum lift coefficient, delayed stall angle, and comparable drag at lower angles. The study established the presence of an additional effect termed as the inclination effect alongside the cascade effect leading to deviations with respect to lift, stall, and aerodynamic efficiency amongst different gap variants of the individual patterns. Thus, optimization based on the aerodynamic efficiency, stall angle requirements, and construction cost by optimum pattern and gap selection can be carried out through this analysis, which can lead to elevated aerodynamic performance for grid fins.

scholarly journals Investigation of High Lift Force Generation of Dragonfly Wing by a Novel Advanced Mode in Hover

Fluids ◽  
2020 ◽  
Vol 5 (2) ◽  
pp. 59
Author(s):  
Xiaohui Su ◽  
Kaixuan Zhang ◽  
Juan Zheng ◽  
Yong Zhao ◽  
Ruiqi Han ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Energy Expenditure ◽  
Lift Force ◽  
Lift Coefficient ◽  
Aerodynamic Performance ◽  
Dynamic Stall ◽  
Force Generation ◽  
High Lift ◽  
Dragonfly Wing ◽  
Symmetrical Mode

In the paper, a novel flapping mode is presented that can generate high lift force by a dragonfly wing in hover. The new mode, named partial advanced mode (PAM), starts pitching earlier than symmetric rotation during the downstroke cycle of the hovering motion. As a result, high lift force can be generated due to rapid pitching coupling with high flapping velocity in the stroke plane. Aerodynamic performance of the new mode is investigated thoroughly using numerical simulation. The results obtained show that the period-averaged lift coefficient, CL, increases up to 16% compared with that of the traditional symmetrical mode when an earlier pitching time is set to 8% of the flapping period. The reason for the high lift force generation mechanism is explained in detail using not only force investigation, but also by analyzing vortices produced around the wing. The proposed PAM is believed to lengthen the dynamic stall mechanism and enhance the LEV generated during the downstroke. The improvement of lift force could be considered as a result of a combination of the dynamic stall mechanism and rapid pitch mechanism. Finally, the energy expenditure of the new mode is also analyzed.

scholarly journals Gurney Flap Implementation on a DU91W250 Airfoil

Proceedings ◽  
2018 ◽  
Vol 2 (23) ◽  
pp. 1448 ◽  
Author(s):  
Iñigo Aramendia ◽  
Aitor Saenz-Aguirre ◽  
Unai Fernandez-Gamiz ◽  
Ekaitz Zulueta ◽  
Jose Manuel Lopez-Guede ◽  
...  
Keyword(s):  
Flow Control ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Optimization Technique ◽  
Electrical Power ◽  
Aerodynamic Performance ◽  
Control Element ◽  
Mechanical Fatigue ◽  
Gurney Flap ◽  
Fatigue Loads

The increasing capability of Wind Turbine (WT) based power generation systems has derived in an increment of the WT rotor diameter, i.e., longer rotor blades. This results in an increase of the electrical power generated but also in instabilities in the operation of the WT, especially due to the mechanical fatigue loads generated in its elements. In this context, flow control has appeared as a solution to improve the aerodynamic performance of the blades. These devices not only increase lift coefficient but also reduce mechanical fatigue loads. This paper presents a detailed numerical analysis of the effects of placing a passive flow control element, a Gurney Flap (GF), in a DU91W250 airfoil. Moreover, a numerical study of the influence of the GF length on the aerodynamic performance of the blade has been carried out. This study is considered as a basis for the development of an optimization technique of the GF length for long WT blades.

scholarly journals Numerical Simulation of a Pitching Airfoil Under Dynamic Stall of Low Reynolds Number Flow

2019 ◽  
Author(s):  
Mojtaba Honarmand ◽  
Mohammad Hassan Djavareshkian ◽  
Behzad Forouzi Feshalami ◽  
Esmaeil Esmaeilifar
Keyword(s):  
Reynolds Number ◽  
Stokes Equations ◽  
Aerodynamic Force ◽  
Low Reynolds Number ◽  
Oscillation Amplitude ◽  
Dynamic Stall ◽  
Aerodynamic Forces ◽  
Naca0012 Airfoil ◽  
Reduced Frequency ◽  
Low Reynolds

In this research, viscous, unsteady and turbulent fluid flow is simulated numerically around a pitching NACA0012 airfoil in the dynamic stall area. The Navier-Stokes equations are discretized based on the finite volume method and are solved by the PIMPLE algorithm in the open source software, namely OpenFOAM. The SST k - ω model is used as the turbulence model for Low Reynolds Number flows in the order of 105. A homogenous dynamic mesh is used to reduce cell skewness of mesh to prevent non-physical oscillations in aerodynamic forces unlike previous studies. In this paper, the effects of Reynolds number, reduced frequency, oscillation amplitude and airfoil thickness on aerodynamic force coefficients and dynamic stall delay are investigated. These parameters have a significant impact on the maximum lift, drag, the ratio of aerodynamic forces and the location of dynamic stall. The most important parameters that affect the maximum lift to drag coefficient ratio and cause dynamic stall delaying are airfoil thickness and reduced frequency, respectively.

Power performance enhancement of vertical axis wind turbines by a novel gurney flap design

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Milad Mousavi ◽  
Mehran Masdari ◽  
Mojtaba Tahani
Keyword(s):  
Wind Turbines ◽  
Vertical Axis ◽  
Dynamics Simulation ◽  
Power Coefficient ◽  
Lower Amount ◽  
Speed Ratio ◽  
Power Performance ◽  
Content Type ◽  
Vertical Axis Wind Turbines ◽  
Gurney Flap

Purpose Nowadays flaps and winglets are one of the main mechanisms to increase airfoil efficiency. This study aims to investigate the power performance of vertical axis wind turbines (VAWT) that are equipped with diverse gurney flaps. This study could play a crucial role in the design of the VAWT in the future. Design/methodology/approach In this paper, the two-dimensional computational fluid dynamics simulation is used. The second-order finite volume method is used for the discretization of the governing equations. Findings The results show that the gurney flap enhances the power coefficient at the low range of tip speed ratio (TSR). When an angled and standard gurney flap case has the same aerodynamic performance, an angled gurney flap case has a lower hinge moment on the junction of airfoil and gurney flap which shows the structural excellence of this case. In all gurney flap cases, the power coefficient increases by an average of 20% at the TSR range of 0.6 to 1.8. The gurney flap cases do not perform well at the high TSR range and the results show a lower amount of power coefficient compare to the clean airfoil. Originality/value The angled gurney flap which has the structural advantage and is deployed to the pressure side of the airfoil improves the efficiency of VAWT at the low and medium range of TSR. This study recommends using a controllable gurney flap which could be deployed at a certain amount of TSR.

Selection of Airfoils for Straight-Bladed Vertical Axis Wind Turbines Based on Desirable Aerodynamic Characteristics

2008 ◽  
Author(s):  
Mazharul Islam ◽  
M. Ruhul Amin ◽  
David S.-K. Ting ◽  
Amir Fartaj
Keyword(s):  
Urban Areas ◽  
Lift Coefficient ◽  
Vertical Axis ◽  
Aerodynamic Characteristics ◽  
Performance Indices ◽  
Niche Markets ◽  
Design Changes ◽  
Stall Angle ◽  
Lift And Drag ◽  
Selection Of

Selection of the airfoil is crucial for better aerodynamic performance and dimensions of a smaller-capacity SB-VAWT which can compete with conventional energy sources in niche markets like urban areas and off-grid remote applications for diversified applications. Airfoil related design changes also have the potential for increasing the cost effectiveness of VAWTs. Recently, Islam et. al [1] have identified the desirable features of an ideal airfoil for smaller capacity SB-VAWT to improve its starting characteristics and overall performance. They have shortlisted several aerodynamic characteristics of the desirable airfoil. Based on these desirable aerodynamic characteristics, an attempt has been made in this paper to shortlist ten prospective candidate airfoils for smaller-capacity SB-VAWT. This is done using both experimental and analytical characteristics. Nine performance indices have been defined in this paper in light of desirable aerodynamic characteristics to select best performing airfoil. These performance indices are utilized for considering the following desirable aerodynamic characteristics: (i) stall angle at low Reynolds number, (ii) width of the drag bucket, (iii) zero-lift-drag coefficient, (iv) Cl/Cd ratio, (v) maximum lift-coefficient, (vi) deep-stall angle, (vii) roughness sensitivity, (viii) trailing edge noise generation, and (ix) pitching moment. Here, Cl and Cd are coefficients of lift and drag respectively. After determining the value of the performance indices and rating of the candidate airfoils, the most promising airfoil is selected. Among the ten candidate airfoils, overall rating of NASA LS(1)-0417 has been found to be the best.

Experimental investigations on the application of lift enhancement devices to forward-swept aircraft model

2006 ◽  
Vol 110 (1108) ◽  
pp. 361-367 ◽  
Author(s):  
W. Zhang ◽  
J. J. Wang ◽  
Z. Wu
Keyword(s):  
Lift Coefficient ◽  
Experimental Investigations ◽  
Aircraft Model ◽  
High Side ◽  
Gurney Flap ◽  
Lift Enhancement ◽  
Stall Angle ◽  
Lift And Drag ◽  
Low Speed Wind Tunnel ◽  
Wing Tip

Abstract The force measurements were conducted in low speed wind tunnel to investigate the effects of the scale, shape and the installation type of Gurney flap on a forward-swept aircraft model. The results indicated that both rectangular and triangular Gurney flaps can enhance the lift coefficient of the model tested, but with a little decrease of stall angle from 38° to 36°. The lift and drag coefficients increased with the Gurney flap scales. Meanwhile, the triangular Gurney flap can improve the aerodynamic performance more effectively when its high side is located near the wing root than the reverse installation with the low side near the wing root and the high side near the wing tip. Additionally, for the same Gurney flap, the model with smaller forward-swept angle can generate higher lift-enhancement in comparison with the larger forward-swept angle model.

scholarly journals Improving the aerodynamic performance of a cycloidal rotor through active compliant morphing

2017 ◽  
Vol 121 (1241) ◽  
pp. 901-915
Author(s):  
L. Ferrier ◽  
M. Vezza ◽  
H. Zare-Behtash
Keyword(s):  
Negative Impact ◽  
Lift Coefficient ◽  
Leading Edge ◽  
Micro Air Vehicles ◽  
Aerodynamic Performance ◽  
Dynamic Stall ◽  
Marine Vehicles ◽  
Aerospace Applications ◽  
Naca 0015 ◽  
Air Vehicles

ABSTRACTCycloidal rotors are a novel form of propulsion system that can be adapted to various forms of transport such as air and marine vehicles, with a geometrical design differing significantly from the conventional screw propeller. Research on cycloidal rotor design began in the early 1930s and has developed throughout the years to the point where such devices now operate as propulsion systems for various aerospace applications such as micro air vehicles, unmanned air vehicles and compound helicopters. The majority of research conducted on the cycloidal rotor’s aerodynamic performance have not assessed mitigating the dynamic stall effect, which can have a negative impact on the rotor performance when the blades operate in the rotor retreating side. A solution has been proposed to mitigate the dynamic stall effect through employment of active, compliant leading-edge morphing. A review of the current state of the art in this area is presented. A two-dimensional, implicit unsteady numerical analysis was conducted using the commercial computational fluid dynamics software package STAR CCM+, on a two-bladed cycloidal rotor. An overset mesh technique, otherwise known as a chimera mesh, was used to apply complex transient motions to the simulations. Active, compliant leading-edge morphing is applied to an oscillating NACA 0015 aerofoil to attempt to mitigate the dynamic stall whilst maintaining the positive dynamic lift coefficient (Cl) contributions. It was verified that by applying a pulsed input leading-edge rotational morphing schedule, the leading-edge vortex does not fully form and the large flow separation is prevented. Further work in this investigation will focus on coupling the active, leading-edge motion to the cycloidal rotor model with the aim to maximise aerodynamic performance.

Sign in / Sign up

Export Citation Format

Share Document