Oil film thickness analysis of the sealing surface for hydraulic rotary rectangular vane actuator

2018 ◽  
Vol 70 (8) ◽  
pp. 1494-1499
Author(s):  
Han Qing ◽  
LiangXi Xie ◽  
Lu Li ◽  
Chuang Jia
Keyword(s):  
Numerical Model ◽  
Film Thickness ◽  
Contact Pressure ◽  
Reynolds Equation ◽  
Distribution Curve ◽  
Contact Pressure Distribution ◽  
Content Type ◽  
Oil Film ◽  
Rotary Actuator ◽  
The Relationship

Purpose This paper aims to establish a numerical model to calculate contact pressure for rectangular vane sealing surface of hydraulic rotary actuator. Numerical model can be applied to solve the steady-state Reynolds equation after the oil film thickness and the contact pressure distribution curve of the vane sealing surface are obtained. Design/methodology/approach The authors established the numerical model of contact pressure base on the theory of elastic after, the Reynolds equation is solved by the inverse solution. Findings The relationship between the oil film thickness of vane sealing surface and the contact pressure on different sealing location for hydraulic rotary actuator is obtained. At the same time, the lubrication state on the surface of seal is also found when the hydraulic rotary actuator runs stably. Originality/value The study shows that the lubricating state of the vane sealing surface is mixed lubrication, when the rotor of the hydraulic rotary actuator is running stably at a certain speed. Meanwhile, this research will provide a theory basis for later experiment for the hydraulic rotary vane actuator.

Lubrication characteristics of the worn slipper in the slipper-swashplate pair

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Haiji Wang ◽  
Guanglin Shi
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Design Methodology ◽  
Reynolds Equation ◽  
Thickness Distribution ◽  
Operating Conditions ◽  
Test Rig ◽  
Content Type ◽  
Oil Film ◽  
Lubrication Characteristics

Purpose This paper proposes the lubrication characteristics of the worn slipper in the slipper–swashplate pair. The mathematical analysis of lubrication characteristics of slipper with the measured surface roughness distribution is introduced. Based on the results from the test rig, it carries out the result compassion in different operating conditions. Design/methodology/approach This paper introduces the measured surface roughness distribution of new and used slippers and generates the oil film thickness distribution with it. An average flow Reynolds equation of the pressure distribution is introduced too. The experimental results are carried out on a novel adjustable oil film thickness test rig. Findings The surface roughness of the worn slipper enlarges the reacting force and torque only if the oil film thickness is small. When the ratio of oil film thickness to the root mean square of surface roughness is much smaller than 3, the influence of it on torque is obvious. Originality/value Different surface roughness of worn slipper proposed in this paper has an influence on the lubrication characteristics. As the slipper is worn after a period of use, the changed lubrication characteristics should be considered in the slipper design.

Analysis on sealing performance of VL seals based on mixed lubrication theory

2019 ◽  
Vol 71 (1) ◽  
pp. 54-60 ◽  
Author(s):  
Shixian Xu ◽  
Zhengtao Su ◽  
Jian Wu
Keyword(s):  
Finite Element ◽  
Film Thickness ◽  
Finite Element Model ◽  
Friction Factor ◽  
Contact Pressure ◽  
Element Model ◽  
Mixed Lubrication ◽  
Content Type ◽  
Deformation Mechanics ◽  
The Finite Element Model

Purpose This paper aims to research the influence of pressure, friction factors, roughness and actuating speed to the mixed lubrication models of outstroke and instroke. Design/methodology/approach Mixed lubrication model is solved by finite volume method, which consists of coupled fluid mechanics, deformation mechanics and contact mechanics analyses. The influence of friction factor on the finite element model is also considered. Then, contact pressure, film thickness, friction and leakage have been studied. Findings It was found that the amount of leakage is sensitive to the film thickness. The larger the film thickness is, the greater the influence received from the friction factor, however, the effect of oil film on the friction is negligible. The friction is determined mainly by the contact pressure. The trend of friction and leakage influenced by actuating velocity and roughness is also obtained. Originality/value The influence of friction factor on the finite element model is considered. This can make the calculation more accurate.

Dynamic transmission of oil film in soft-start process of HVD considering surface roughness

2018 ◽  
Vol 70 (3) ◽  
pp. 463-473 ◽  
Author(s):  
Fangwei Xie ◽  
Jie Zhu ◽  
Jianzhong Cui ◽  
Xudong Zheng ◽  
Xinjian Guo ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Friction Pair ◽  
Maximum Temperature ◽  
Force Model ◽  
Content Type ◽  
Oil Film ◽  
Soft Start ◽  
Viscous Torque ◽  
Start Process

Purpose The purpose of this paper is to study the dynamic transmission of the oil film in soft start process of hydro-viscous drive (HVD) between the friction pairs with consideration of surface roughness, and obtain the distribution law of temperature, velocity, pressure, shear stress and viscous torque of the oil film. Design/methodology/approach The revised soft-start models of HVD were derived and calculated, including average Reynolds equation, asperity contact model, load force model and total torque model. Meanwhile, a 2D model of the oil film between friction pair was built and solved numerically using computational fluid dynamics (CFD) technique in FLUENT. Findings The results show that the maximum temperature gradually reduces from the intermediate range (z = 0.5 h) to the inner side of the friction pair along the direction of oil film thickness. As the soft-start process continues, pressure gradient along the direction of the oil film thickness gradually changes to zero. In addition, tangential velocity increases and yet radial velocity decreases with the increase of the radius. Originality/value In this paper, it was found that the viscous torque calculated by the numerical method is smaller than that by the CFD model, but their overall trend is almost the same. This also demonstrates the effectiveness of the numerical simulation.

Measurement and calculation of oil film thickness in a ball bearing

2018 ◽  
Vol 70 (8) ◽  
pp. 1500-1508 ◽  
Author(s):  
Baogang Wen ◽  
Hongjun Ren ◽  
Pengfei Dang ◽  
Xu Hao ◽  
Qingkai Han
Keyword(s):  
Film Thickness ◽  
Ball Bearing ◽  
Performance Indicator ◽  
Thickness Distribution ◽  
Content Type ◽  
Oil Film ◽  
Capacitance Method ◽  
Lubrication Condition ◽  
Series Of Experiments ◽  
External Loads

PurposeThe oil film thickness provides a key performance indicator of a ball bearing lubrication condition. This paper aims to propose an approach to calculate and measure the oil film thickness of the bearing.Design/methodology/approachOn a specially designed test rig, measurement of the capacitance is used to monitor the oil film thickness of ball bearing. A corrected film thickness formula taking account of the influences of non-Newtonian shear thinning and thermal is introduced to predict the oil film thickness of ball bearing. And then the film thickness distribution and the corresponding capacitances are calculated.FindingsMeasurement and calculation of oil film thickness in a ball bearing are carried out under various rotating speeds and external loads. By comparing the calculated capacitances with measured results, it can be concluded that the calculated results obtained by the amended film thickness formula are much closer to the test findings than the classical computed values according to Hamrock–Dowson.Originality/valueA new corrected film thickness formula is introduced in predicting oil film thickness of ball bearing and verified by the series of experiments according to capacitance method.

Experimental study on line-contact elastohydrodynamic grease lubrication properties of surface-textured rollers

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Fuqin Yang ◽  
Dexing Hu ◽  
Qianhao Xiao ◽  
Shun Zhao
Keyword(s):  
Film Thickness ◽  
Surface Texture ◽  
Inhibitory Effect ◽  
Lubricating Oil ◽  
Line Contact ◽  
Grease Lubrication ◽  
Content Type ◽  
Oil Film ◽  
Crown Width ◽  
Lubrication Properties

Purpose This paper aims to study line-contact elastohydrodynamic grease lubrication properties of surface-textured rollers as well as the effect of different crown widths (dw) on oil film thickness under textured conditions. Design/methodology/approach The laser processing method was used to make the micro-texture on the surface of GCr15 steel rollers; lithium grease was used as the lubricant, and line-contact elastohydrodynamic grease lubrication experiments under pure sliding conditions were performed on light interference elastohydrodynamic-lubricated experimental table. Findings The results show that the line-contact elastohydrodynamic grease lubrication is closely related to the textured crown width of steel rollers. At low speeds and light loads, texturing has an inevitable inhibitory effect on the formation of the lubricating oil film, and the smaller the width of the crown area, the more obvious the inhibitory effect, which is not conducive to the improvement of the lubrication condition. At high speeds and high loads, the textured roller with dw = 1 mm has the largest oil film thickness and shows better lubrication performance. Originality/value At present, there is little research on the surface texture of line-contact friction pairs. This work explores the effect of different textured crown width on the lubricating properties of line-contact elastohydrodynamic grease lubrication by experiment. It provides a new theoretical basis for the subsequent practical application of surface texture technology.

Numerical analysis of the transient wear and lubrication behaviors of misaligned journal bearings caused by linear shaft misalignment

2021 ◽  
pp. 1-17
Author(s):  
Tianyou Yang ◽  
Yanfeng Han ◽  
Yijia Wang ◽  
Guo Xiang
Keyword(s):  
Numerical Model ◽  
Film Thickness ◽  
Contact Pressure ◽  
Elastic Deformation ◽  
Journal Bearing ◽  
Fluid Pressure ◽  
Axial Direction ◽  
Wear Depth ◽  
Wear Process ◽  
Journal Misalignment

Abstract The purpose of this study is to investigate the role of the misalignment journal, caused by journal elastic deformation, on the transient wear and mixed lubrication performances using a numerical model. In the numerical model, the transient geometry lubrication clearance considering the journal misalignment, the transient elastic deformation and the transient wear depth are incorporated to evaluate the transient film thickness during wear process. The evolutions, under different external loads, of the wear depth, wear rate, elastic deformation, film thickness, fluid pressure and contact pressure are calculated by the numerical model. Furthermore, the calculated results of the misaligned journal bearing are compared with those of the aligned journal bearing. The results show that the distributions of the wear depth, film pressure and elastic deformation are asymmetric along the axial direction and the peak values of them shift toward the back end when the journal misalignment is considered. The maximum wear depth, maximum fluid pressure, maximum contact pressure and maximum elastic deformation of the misaligned journal condition are significantly larger than those of the aligned journal condition.

Size effect on thermal elastohydrodynamic lubrication of industrial chain bush-pin hinge pair

2019 ◽  
Vol 71 (9) ◽  
pp. 1080-1085 ◽  
Author(s):  
Mingyu Zhang ◽  
Jing Wang ◽  
Yi Liu ◽  
Longjie Dai ◽  
Zhaohua Shang
Keyword(s):  
Friction Coefficient ◽  
Film Thickness ◽  
Temperature Rise ◽  
Elastohydrodynamic Lubrication ◽  
Curvature Radius ◽  
Line Contact ◽  
Content Type ◽  
Oil Film ◽  
Industrial Chain ◽  
Infinite Line

Purpose The purpose of this paper is to use elastohydrodynamic lubrication (EHL) theory to study the variation of the equivalent curvature radius “R” on the change of oil film thickness, pressure, temperature rise and friction coefficient in the contact zone between bush-pin in industrial chain drive. Design/methodology/approach In this paper, the contact between bush and pin is simplified as infinitely long line contact. The lubrication state is studied by numerical simulation using steady-state line contact thermal EHL. The two constitutive equations, namely, Newton fluid and Ree–Eyring fluid are used in the calculations. Findings It is found that with the increase of equivalent curvature radius, the thickness of oil film decreases and the temperature rise increases. Under the same condition, the friction coefficient of Newton fluid is higher than that of Ree–Eyring fluid. When the load increases, the oil film thickness decreases, the temperature rise increases and the friction coefficient decreases; and the film thickness increases with the increase of the entraining speed under the condition “R < 1,000 mm”. Research limitations/implications The infinite line contact assumption is only an approximation. For example, the distances between the two inner plates are 5.72 mm, by considering the two parts assembled into the inner plates, the total length of the bush is less than 6 mm. The diameter of the pin and the bore diameter of the bush are 3.28 and 3.33 mm. However, the infinite line contact is also helpful in understanding the general variation of oil film characteristics and provides a reference for the future study of finite line contact of chain problems. Originality/value The change of the equivalent radius R on the variation of the oil film in the contact of the bush and the pin in industrial chain drive was investigated. The size effect influences the lubrication characteristic greatly in the bush-pin pair.

A thermal EHL investigation for size effect of finite line contact on bush-pin hinge pairs in industrial chains

2020 ◽  
Vol 72 (5) ◽  
pp. 695-701
Author(s):  
Mingyu Zhang ◽  
Jing Wang ◽  
Peiran Yang ◽  
Zhaohua Shang ◽  
Yi Liu ◽  
...  
Keyword(s):  
Film Thickness ◽  
Peer Review ◽  
Contact Zone ◽  
Line Contact ◽  
Equivalent Radius ◽  
Content Type ◽  
Oil Film ◽  
Finite Line Contact ◽  
Finite Line ◽  
Thermal Ehl

Purpose This paper aims to study the influence of the dimension change of bush-pin on the pressure, oil film thickness, temperature rise and traction coefficient in contact zone by using a thermal elastohydrodynamic lubrication (EHL) model for finite line contact. Concretely, the effects of the equivalent curvature radius of the bush and the pin, and the length of the bush are investigated. Design/methodology/approach In this paper, the contact between the bush and pin is simplified as finite line contact. The lubrication state is studied by numerical simulation using steady-state line contact thermal EHL. A constitutive equation Ree–Eyring fluid is used in the calculations. Findings It is found that by selecting an optimal equivalent radius of curvature and prolonging the bush length can improve the lubrication state effectively. Originality/value Under specific working conditions, there exists an optimal equivalent radius to maximize the minimum oil film thickness in the contact zone. The increase of generatrix length will weaken the stress concentration effect in the rounded corner area at both ends of the bush, which can improve the wear resistance of chain. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-10-2019-0448.

An adjustable oil film thickness test rig for detecting lubrication characteristics of slipper/swash-pair in piston pumps

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Haiji Wang ◽  
Guanglin Shi
Keyword(s):  
Film Thickness ◽  
Peer Review ◽  
Relative Error ◽  
Mathematical Analysis ◽  
Test Rig ◽  
Content Type ◽  
Oil Film ◽  
Displacement Sensors ◽  
Measuring Machine ◽  
Lubrication Characteristics

Purpose The purpose of this paper is to propose an adjustable oil film thickness test rig for detecting lubrication characteristics of the slipper. The mathematical analysis of lubrication is introduced. Based on the results from the test rig, the results comparison from test rig and mathematical analysis is carried out. Design/methodology/approach This paper introduces a mechanism which can adjust the oil film thickness between the slipper and swash-plate. Feasibility is ensured, and the accuracy of test rig is guaranteed by the three-coordinate measuring machine. Three displacement sensors show the oil film thickness and its shape. The reacting force and torque resulting from oil film can be achieved by three S-type force sensors and a torque sensor, respectively. Findings The relative error of the reacting force is small. The relative error reduces and is acceptable when the deformation of retainer is taken into account. The thickness and tilt angle of oil film have less effect on the reacting force. However, they are significantly impact on torque. Originality/value The test rig proposed in this paper is able to adjust the oil film thickness, which is used to detecting the lubrication characteristics in pump design. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2020-0166/

Sign in / Sign up

Export Citation Format

Share Document