Research on the Reflection Characteristic of Flying Electromagnetic Toroid Pulses on an Inclined Air-metal Interface

2019 ◽  
Author(s):  
Sheng Liu ◽  
Ren Wang ◽  
Mo-Ran Zhang ◽  
Bing-Zhong Wang
Keyword(s):  
Metal Interface ◽  
Reflection Characteristic

The oxidation of Inconel alloy MA754 at low oxidation potential

1983 ◽  
Vol 41 ◽  
pp. 218-219
Author(s):  
D. N. Braski ◽  
P. D. Goodell ◽  
J. V. Cathcart ◽  
R. H. Kane
Keyword(s):  
Surface Layer ◽  
Oxidation Potential ◽  
Metal Interface ◽  
Elevated Temperature Strength ◽  
Surface Conditions ◽  
Inconel Alloy ◽  
Inco Alloy ◽  
Resistance To Oxidation ◽  
Oxide Particles ◽  
Cold Worked

It has been known for some time that the addition of small oxide particles to an 80 Ni—20 Cr alloy not only increases its elevated-temperature strength, but also markedly improves its resistance to oxidation. The mechanism by which the oxide dispersoid enhances the oxidation resistance is being studied collaboratively by ORNL and INCO Alloy Products Company.Initial experiments were performed using INCONEL alloy MA754, which is nominally: 78 Ni, 20 Cr, 0.05 C, 0.3 Al, 0.5 Ti, 1.0 Fe, and 0.6 Y2O3 (wt %).Small disks (3 mm diam × 0.38 mm thick) were cut from MA754 plate stock and prepared with two different surface conditions. The first was prepared by mechanically polishing one side of a disk through 0.5 μm diamond on a syntron polisher while the second used an additional sulfuric acid-methanol electropolishing treatment to remove the cold-worked surface layer. Disks having both surface treatments were oxidized in a radiantly heated furnace for 30 s at 1000°C. Three different environments were investigated: hydrogen with nominal dew points of 0°C, —25°C, and —55°C. The oxide particles and films were examined in TEM by using extraction replicas (carbon) and by backpolishing to the oxide/metal interface. The particles were analyzed by EDS and SAD.

Preparation of cross-sectional samples for near-surface TEM studies

1987 ◽  
Vol 45 ◽  
pp. 380-381
Author(s):  
R.C. Dickenson ◽  
K.R. Lawless
Keyword(s):  
Standard Sample ◽  
Surface Region ◽  
Specimen Preparation ◽  
Thick Sheet ◽  
Drill Bit ◽  
Sample Holder ◽  
Metal Interface ◽  
Cross Sectional ◽  
Near Surface ◽  
Cold Worked

In thermal oxidation studies, the structure of the oxide-metal interface and the near-surface region is of great importance. A technique has been developed for constructing cross-sectional samples of oxidized aluminum alloys, which reveal these regions. The specimen preparation procedure is as follows: An ultra-sonic drill is used to cut a 3mm diameter disc from a 1.0mm thick sheet of the material. The disc is mounted on a brass block with low-melting wax, and a 1.0mm hole is drilled in the disc using a #60 drill bit. The drill is positioned so that the edge of the hole is tangent to the center of the disc (Fig. 1) . The disc is removed from the mount and cleaned with acetone to remove any traces of wax. To remove the cold-worked layer from the surface of the hole, the disc is placed in a standard sample holder for a Tenupol electropolisher so that the hole is in the center of the area to be polished.

A microscopic marker experiment study on high temperature oxidation of Ni-Al alloy

1986 ◽  
Vol 44 ◽  
pp. 514-515
Author(s):  
Shou-kong Fan
Keyword(s):  
Transport Mechanism ◽  
High Temperature Oxidation ◽  
Transverse Section ◽  
Al Alloy ◽  
Metal Interface ◽  
Electron Microscopic ◽  
Temperature Oxidation ◽  
Analytical Electron ◽  
Microscopic Studies ◽  
First Time

Transmission and analytical electron microscopic studies of scale microstructures and microscopic marker experiments have been carried out in order to determine the transport mechanism in the oxidation of Ni-Al alloy. According to the classical theory, the oxidation of nickel takes place by transport of Ni cations across the scale forming new oxide at the scale/gas interface. Any markers deposited on the Ni surface are expected to remain at the scale/metal interface after oxidation. This investigation using TEM transverse section techniques and deposited microscopic markers shows a different result,which indicates that a considerable amount of oxygen was transported inward. This is the first time that such fine-scale markers have been coupled with high resolution characterization instruments such as TEM/STEM to provide detailed information about evolution of oxide scale microstructure.

Development of New Apparatus to Evaluate Ultrasonic Reflection Characteristic for Wrinkling in Press Forming

2017 ◽  
Vol 10 (02) ◽  
pp. 170-174 ◽  
Author(s):  
YUJI SEGAWA ◽  
TAKUYA KURIYAMA ◽  
YASUO MARUMO ◽  
TAEKYUNG LEE ◽  
YASUHIRO IMAMURA ◽  
...  
Keyword(s):  
Reflection Characteristic ◽  
Press Forming ◽  
New Apparatus

Spectroscopy of boson excitations in a nanoscale vicinity of a doped-manganite-metal interface

2009 ◽  
Vol 35 (3) ◽  
pp. 243-246 ◽  
Author(s):  
V. M. Svistunov ◽  
V. N. Leonova ◽  
M. A. Belogolovskii ◽  
M. A. Obolensky ◽  
T. Endo ◽  
...  
Keyword(s):  
Metal Interface

scholarly journals Numerical Simulation Analysis of Ag Crystallite Effects on Interface of Front Metal and Silicon in the PERC Solar Cell

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 592
Author(s):  
Myeong Sang Jeong ◽  
Yonghwan Lee ◽  
Ka-Hyun Kim ◽  
Sungjin Choi ◽  
Min Gu Kang ◽  
...  
Keyword(s):  
Solar Cells ◽  
Solar Cell ◽  
High Efficiency ◽  
Open Circuit Voltage ◽  
Surface Recombination ◽  
Open Circuit ◽  
Surface Recombination Velocity ◽  
Metal Interface ◽  
Ag Crystallites ◽  
Recombination Velocity

In the fabrication of crystalline silicon solar cells, the contact properties between the front metal electrode and silicon are one of the most important parameters for achieving high-efficiency, as it is an integral element in the formation of solar cell electrodes. This entails an increase in the surface recombination velocity and a drop in the open-circuit voltage of the solar cell; hence, controlling the recombination velocity at the metal-silicon interface becomes a critical factor in the process. In this study, the distribution of Ag crystallites formed on the silicon-metal interface, the surface recombination velocity in the silicon-metal interface and the resulting changes in the performance of the Passivated Emitter and Rear Contact (PERC) solar cells were analyzed by controlling the firing temperature. The Ag crystallite distribution gradually increased corresponding to a firing temperature increase from 850 ∘C to 950 ∘C. The surface recombination velocity at the silicon-metal interface increased from 353 to 599 cm/s and the open-circuit voltage of the PERC solar cell decreased from 659.7 to 647 mV. Technology Computer-Aided Design (TCAD) simulation was used for detailed analysis on the effect of the surface recombination velocity at the silicon-metal interface on the PERC solar cell performance. Simulations showed that the increase in the distribution of Ag crystallites and surface recombination velocity at the silicon-metal interface played an important role in the decrease of open-circuit voltage of the PERC solar cell at temperatures of 850–900 ∘C, whereas the damage caused by the emitter over fire was determined as the main cause of the voltage drop at 950 ∘C. These results are expected to serve as a steppingstone for further research on improvement in the silicon-metal interface properties of silicon-based solar cells and investigation on high-efficiency solar cells.

Insight into the strengthening mechanism of α-Al2O3/γ-Fe ceramic-metal interface doped with Cr, Ni, Mg, and Ti

2021 ◽  
Author(s):  
Renwei Li ◽  
Qicheng Chen ◽  
Liang Ouyang ◽  
Yingjin Zhang ◽  
Binjian Nie ◽  
...  
Keyword(s):  
Strengthening Mechanism ◽  
Metal Interface ◽  
Α Al2o3 ◽  
Insight Into
Sign in / Sign up

Export Citation Format

Share Document