Improved Matlab Simulink Two-diode Model of PV Module and Method of Fast Large-Scale PV System Simulation

2018 ◽  
Author(s):  
Tai Le ◽  
Herve Colin ◽  
Franck Al Shakarchi ◽  
Tuan Tran Quoc
Keyword(s):  
Large Scale ◽  
System Simulation ◽  
Pv System ◽  
Matlab Simulink ◽  
Pv Module

scholarly journals MPPT of PV System Under Partial Shading Conditions Based on Bio-inspired Swarm Intelligence Technique

2021 ◽  
Vol 297 ◽  
pp. 01051
Author(s):  
Mohammed Agdam ◽  
Abdallah Asbayou ◽  
Mustapha Elyaqouti ◽  
Ahmed Ihlal ◽  
Khaled Assalaou
Keyword(s):  
Swarm Intelligence ◽  
Electrical Energy ◽  
Pv System ◽  
Partial Shading ◽  
Matlab Simulink ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Maximum Current ◽  
Maximum Voltage ◽  
Intelligence Technique

To respond to the increase in demand for electricity, the use of photovoltaics is growing considerably as it produces electrical energy without polluting the environment. In addition, to enhance the efficiency of photovoltaic modules, an MPPT algorithm is required to follow the maximum voltage and maximum current in the IV curve. This technique can be achieved by using a DC-DC converter. For this purpose, various MPPT techniques have been developed. The combination of MPPT and DC-DC converter is implemented using Matlab/Simulink and connected to a modelled PV module to validate the simulation.

scholarly journals Behavioral Characteristics of Photovoltaic Cell with Different Irradiation in Matlab/Simuling/Simscape Environment

2014 ◽  
Vol 36 ◽  
pp. 316-326 ◽  
Author(s):  
Hamisu Usman ◽  
S.M. Lawal ◽  
R.S. Shehu
Keyword(s):  
Mathematical Modeling ◽  
Carbon Dioxide ◽  
Electricity Generation ◽  
System Simulation ◽  
Photovoltaic Cell ◽  
Behavioral Characteristics ◽  
Pv System ◽  
Matlab Simulink ◽  
Proposed Model ◽  
Simulation Results

Photovoltaic technology is one of the fastest growing energy among the different type of renewable energies that are available for electricity generation. This is due to the availability of the natural sun rise, and the non polluted energy that is free from emission of carbon dioxide (CO2). This paper presents a typical modeling of photovoltaic cell under different irradiations level, in order to monitor the behavior of the (Voltage-Current) V-I and (Power-Voltage) P-V characteristics. The simulation of the proposed model was performed in MATLAB/SIMULINK and Simscape environment. Single diode model of the PV system was presented in the mathematical modeling of the proposed system. Simulation results of different I-V and P-V characteristics were also presented.

scholarly journals An Experimental and Comparative Performance Evaluation of a Hybrid Photovoltaic-Thermoelectric System

2021 ◽  
Vol 9 ◽  
Author(s):  
Muhammad Ahsan Iqbal Khan ◽  
Muhammad Irfan Khan ◽  
Ali Hussain Kazim ◽  
Aqsa Shabir ◽  
Fahid Riaz ◽  
...  
Keyword(s):  
Output Power ◽  
Conversion Efficiency ◽  
Hybrid System ◽  
Large Scale ◽  
Total Output ◽  
Photovoltaic Module ◽  
Rear Side ◽  
Pv System ◽  
Thermoelectric Modules ◽  
Pv Module

The majority of incident solar irradiance causes thermalization in photovoltaic (PV) cells, attenuating their efficiency. In order to use solar energy on a large scale and reduce carbon emissions, their efficiency must be enhanced. Effective thermal management can be utilized to generate additional electrical power while simultaneously improving photovoltaic efficiency. In this work, an experimental model of a hybrid photovoltaic-thermoelectric generation (PV-TEG) system is developed. Ten bismuth telluride-based thermoelectric modules are attached to the rear side of a 10 W polycrystalline silicon-based photovoltaic module in order to recover and transform waste thermal energy to usable electrical energy, ultimately cooling the PV cells. The experiment was then carried out for 10 days in Lahore, Pakistan, on both a simple PV module and a hybrid PV-TEG system. The findings revealed that a hybrid system has boosted PV module output power and conversion efficiency. The operating temperature of the PV module in the hybrid system is reduced by 5.5%, from 55°C to 52°C. Due to a drop in temperature and the addition of some recovered energy by thermoelectric modules, the total output power and conversion efficiency of the system increased. The hybrid system’s cumulative output power increased by 19% from 8.78 to 10.84 W, compared to the simple PV system. Also, the efficiency of the hybrid PV-TEG system increased from 11.6 to 14%, which is an increase of 17% overall. The results of this research could provide consideration for designing commercial hybrid PV-TEG systems.

scholarly journals Modeling and Simulation of a PV Module Based Power System Using MATLAB/Simulink

2015 ◽  
Vol 62 (2) ◽  
pp. 127-132 ◽  
Author(s):  
Protap Kumar Mahanta ◽  
Khokan Debnath ◽  
Md Habibur Rahman
Keyword(s):  
Solar Irradiance ◽  
Maximum Power ◽  
Solar Pv ◽  
Pv System ◽  
Matlab Simulink ◽  
Pv Module ◽  
Power Stage ◽  
In Series ◽  
Natural Variable ◽  
And Performance

Due to the variation of solar irradiance, temperature and shading conditions, the power generated by a photovoltaic (PV) module and hence the power delivered to the load changes drastically, which imposes the need for analysis of a complete PV system to get the maximum power under these natural variable conditions. In this paper, a complete off-grid PV module based power generation system has been designed and simulated using MATLAB/Simulink and performance has been scrutinized using the value of standard solar irradiance about 1 KW/m-2 for Bangladesh. The simulation model includes solar PV module, the converter power stage with MPPT control and charge controlling functions and here performance of each block has been examined conspicuously. Eventually, it has been found that the model is quite competent to simulate both the I-V and P-V characteristics of a PV module and based on the result it has been predicted that the performance of several modules or even PV array connected in series and/or in parallel with the delivery of maximum power can be tested under different solar irradiance and temperature conditions. DOI: http://dx.doi.org/10.3329/dujs.v62i2.21977 Dhaka Univ. J. Sci. 62(2): 127-132, 2014 (July)

Performance assessment of free standing and building integrated grid connected photovoltaic system for southern part of India

2020 ◽  
pp. 014362442097774
Author(s):  
VS Chandrika ◽  
M Mohamed Thalib ◽  
Alagar Karthick ◽  
Ravishankar Sathyamurthy ◽  
A Muthu Manokar ◽  
...  
Keyword(s):  
Geographical Location ◽  
Photovoltaic System ◽  
Building Structures ◽  
System Efficiency ◽  
Pv System ◽  
Free Standing ◽  
Pv Module ◽  
Building Integrated Photovoltaic ◽  
Community Buildings ◽  
Equatorial Climate

Photovoltaic (PV) system efficiency depends on the geographical location and the orientation of the building. Until installing the building structures, the integration of the PV module must be evaluated with ventilation and without ventilation effects. This work optimises the performance of the 250 kWp grid-connected photovoltaic (GPV) for community buildings in the southern part of India. This simulation is carried out to evaluate the system efficiency of the GPV system under various ventilation conditions, such as free-standing PV (FSPV), building integrated photovoltaic ventilated (BIPV_V) and Building Integrated Photovoltaic without ventilation (BIPV). The PVsyst simulation tool is used to simulate and optimise the performance of the system with FSPV, BIPV and BIPV_V for the region of Chennai (13.2789° N, 80.2623° E), Tamilnadu, India. An annual system energy production is 446 MWh, 409 MWh and 428 MWh of FSPV, BIPV and BIPV_V system respectively. while electrical efficiency for the FSPV, BIPV_V, BIPV system is 15.45%. 15.25% and 14.75% respectively. Practical application: Integrating the grid connected photovoltaic system on the building reduces the energy consumption in the building. The integration of the PV on the roof or semi integrated on the roof is need to be investigated before installing on the buildings. The need for installation of the BIPV with ventilation is explored. This study will assist architects and wider community to design buildings roofs with GPV system which are more aesthetic and account for noise protection and thermal insulation in the region of equatorial climate zones.

scholarly journals Influence of Parasitic Parameters on DC–DC Converters and Their Method of Suppression in High Frequency Link 35 kV PV Systems

Energies ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3743
Author(s):  
Rui Li ◽  
Fangyuan Shi ◽  
Xu Cai ◽  
Haibo Xu
Keyword(s):  
High Frequency ◽  
Large Scale ◽  
Pv System ◽  
Zero Voltage Switching ◽  
Pv Systems ◽  
Magnetic Inductance ◽  
Parasitic Parameters ◽  
Saturable Inductor ◽  
Secondary Side ◽  
Pv Power Generation

Photovoltaic (PV) power generation has shown a trend towards large-scale medium- or high-voltage integration in recent years. The development of high-frequency link PV systems is necessary for the further improvement of system efficiency and the reduction of system cost. In the system, high-frequency high-step-up ratio LLC converters are one of the most important parts. However, the parasitic parameters of devices lead to a loss of zero-voltage switching (ZVS) in the LLC converter, greatly reducing the efficiency of the system, especially in such a high-frequency application. In this paper, a high-frequency link 35 kV PV system is presented. To suppress the influences of parasitic parameters in the LLC converter in the 35 kV PV system, the influence of parasitic parameters on ZVS is analyzed and expounded. Then, a suppression method is proposed to promote the realization of ZVS. This method adds a saturable inductor on the secondary side to achieve ZVS. The saturable inductor can effectively prevent the parasitic elements of the secondary side from participating in the resonance of the primary side. The experimental results show that this method achieves a higher efficiency than the traditional method by reducing the magnetic inductance.

scholarly journals Design of a Building-Integrated Photovoltaic System with a Novel Bi-Reflector PV System (BRPVS) and Optimal Control Mechanism: An Experimental Study

Electronics ◽  
2018 ◽  
Vol 7 (7) ◽  
pp. 119 ◽  
Author(s):  
Muhammad Khan ◽  
Kamran Zeb ◽  
Waqar Uddin ◽  
P. Sathishkumar ◽  
Muhammad Ali ◽  
...  
Keyword(s):  
Low Cost ◽  
Input Voltage ◽  
Photovoltaic System ◽  
Solar Pv ◽  
Pv System ◽  
Building Integrated Photovoltaics ◽  
Pv Module ◽  
Solar Pv System ◽  
Zero Carbon ◽  
The Cost

Environment protection and energy saving are the most attractive trends in zero-carbon buildings. The most promising and environmentally friendly technique is building integrated photovoltaics (BIPV), which can also replace conventional buildings based on non-renewable energy. Despite the recent advances in technology, the cost of BIPV systems is still very high. Hence, reducing the cost is a major challenge. This paper examines and validates the effectiveness of low-cost aluminum (Al) foil as a reflector. The design and the performance of planer-reflector for BIPV systems are analyzed in detail. A Bi-reflector solar PV system (BRPVS) with thin film Al-foil reflector and an LLC converter for a BIPV system is proposed and experimented with a 400-W prototype. A cadmium–sulfide (CdS) photo-resistor sensor and an Arduino-based algorithm was developed to control the working of the reflectors. Furthermore, the effect of Al-foil reflectors on the temperature of PV module has been examined. The developed LLC converter confirmed stable output voltage despite large variation in input voltage proving its effectiveness for the proposed BRPVS. The experimental results of the proposed BRPVS with an Al-reflector of the same size as that of the solar PV module offered an enhancement of 28.47% in the output power.

Sign in / Sign up

Export Citation Format

Share Document