Regression Model for the Specific Contact Resistance of SiC Ohmic Contacts

2021 ◽  
pp. 1-1
Author(s):  
Jordan R. Nicholls ◽  
Sima Dimitrijev
Keyword(s):  
Contact Resistance ◽  
Regression Model ◽  
Ohmic Contacts ◽  
Specific Contact Resistance ◽  
Specific Contact

Improvement of the Specific Contact Resistance on P-Type 4H-SiC by Using a Highly P-Typed Doped 4H-SiC Layer Selectively Grown by VLS Transport

2014 ◽  
Vol 806 ◽  
pp. 57-60
Author(s):  
Nicolas Thierry-Jebali ◽  
Arthur Vo-Ha ◽  
Davy Carole ◽  
Mihai Lazar ◽  
Gabriel Ferro ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Schottky Barrier Height ◽  
Annealing Temperature ◽  
Process Condition ◽  
Specific Contact Resistance ◽  
High Doping Level ◽  
Annealing Temperatures ◽  
Specific Contact ◽  
P Type

This work reports on the improvement of ohmic contacts made on heavily p-type doped 4H-SiC epitaxial layer selectively grown by Vapor-Liquid-Solid (VLS) transport. Even before any annealing process, the contact is ohmic. This behavior can be explained by the high doping level of the VLS layer (Al concentration > 1020 cm-3) as characterized by SIMS profiling. Upon variation of annealing temperatures, a minimum value of the Specific Contact Resistance (SCR) down to 1.3x10-6 Ω.cm2 has been obtained for both 500 °C and 800 °C annealing temperature. However, a large variation of the SCR was observed for a same process condition. This variation is mainly attributed to a variation of the Schottky Barrier Height.

Current Transport in Ti/Al/Ni/Au Ohmic Contacts to GaN and AlGaN

2007 ◽  
Vol 556-557 ◽  
pp. 1027-1030 ◽  
Author(s):  
Ferdinando Iucolano ◽  
Fabrizio Roccaforte ◽  
Filippo Giannazzo ◽  
A. Alberti ◽  
Vito Raineri
Keyword(s):  
Contact Resistance ◽  
Field Emission ◽  
Ohmic Contacts ◽  
Theoretical Models ◽  
Specific Contact Resistance ◽  
Strong Increase ◽  
Current Transport ◽  
Electrical Characteristics ◽  
Structural And Electrical Properties ◽  
Specific Contact

In this work, the structural and electrical properties of Ti/Al/Ni/Au contacts on n-type Gallium Nitride were studied. An ohmic behaviour was observed after annealing above 700°C. The structural analysis showed the formation of an interfacial TiN layer and different phases in the reacted layer (AlNi, AlAu4, Al2Au) upon annealing. The temperature dependence of the specific contact resistance demonstrated that the current transport occurs through thermoionic field emission in the contacts annealed at 600°C, and field emission after annealing at higher temperatures. By fitting the data with theoretical models, a reduction of the Schottky barrier from 1.21eV after annealing at 600°C to 0.81eV at 800°C was demonstrated, together with a strong increase of the carrier concentration at the interface. The reduction of the contact resistance upon annealing was discussed by correlating the structural and electrical characteristics of the contacts.

Modelling Geometrical Effects of Parasitic and Contact Resistance of FET Devices

1996 ◽  
Vol 427 ◽  
Author(s):  
Geoffrey K. Reeves ◽  
H. Barry Harrison ◽  
Patrick W. Leech
Keyword(s):  
Contact Resistance ◽  
Material Properties ◽  
Ohmic Contacts ◽  
Difficult Problem ◽  
Specific Contact Resistance ◽  
Metal Silicide ◽  
Transmission Line Model ◽  
Specific Contact ◽  
Geometrical Effects ◽  
Contact Parameters

AbstractThe continual trend in decreasing the dimensions of semiconductor devices results in a number of technological problems. One of the more significant of these is the increase in contact resistance, Rc. In order to understand and counteract this increase, Rc needs to be quantitatively modelled as a function of the geometrical and material properties of the contact. However the use of multiple semiconductor layers for ohmic contacts makes the modelling and calculation of Rc a more difficult problem. In this paper, a Tri-Layer Transmission Line Model (TLTLM) is used to analyse a MOSFET ohmic contact and gatedrain region. A quantitative assessment of the influence on Rc of important contact parameters such as the metal-silicide specific contact resistance, the silicide-silicon specific contact resistance and the gate-drain length can thus be made. The paper further describes some of the problems that may be encountered in defining Rc when the dimensions of certain types of contact found in planar devices decrease.

Ohmic Contacts to p-Type InGaAs/InP with a Graded Bandgap Heterobarrier

1993 ◽  
Vol 318 ◽  
Author(s):  
Patrick W. Leech ◽  
Geoffrey K. Reeves
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Rutherford Backscattering Spectrometry ◽  
Specific Contact Resistance ◽  
Superlattice Structure ◽  
Specific Contact ◽  
P Type ◽  
Metal Layers ◽  
Anneal Temperature ◽  
Graded Bandgap

ABSTRACTOhmic contacts to p-type InP with an In0.47Ga0.53As buffer layer and an interposed superlattice of 50 Å In0.47Ga0.53As/ 50 Å InP have been investigated. Initial studies of contacts to In0.47Ga0.53As/ InP without the superlattice structure have shown that Pd/Zn/Pd/Au metallization produced a lower specific contact resistance (pc = 1.1 × 10−4 Ω cm2) than Pd/Ge/Au, and over a wider range of anneal temperature than Au/Zn/Au. The incorporation of the superlattice in the p-In0.47Ga0.53As/ InP structure resulted in Pd/Zn/Pd/Au contacts with pc of 3.2 × 10−5 Ω cm2 as-deposited and 7.5 × 10−6 Ω.cm2 after a 500 °C anneal. The presence of Pd/Zn in the metallization was shown as important in reducing pc. Significant intermixing of the metal layers and In0.47Ga0.53As occured at ≥ 350 °C, as revealed by Rutherford backscattering spectrometry.

Ni-Al-Ti Ohmic Contacts with Preserved Form Factor and Few 10- 4 Ωcm2 Specific Resistance on 0.1-1 Ωcm p-Type 4H-SiC

2018 ◽  
Vol 924 ◽  
pp. 385-388 ◽  
Author(s):  
Roberta Nipoti ◽  
Maurizio Puzzanghera ◽  
Maria Concetta Canino ◽  
Giovanna Sozzi ◽  
Paolo Fedeli
Keyword(s):  
Form Factor ◽  
Contact Resistance ◽  
Contact Area ◽  
Room Temperature ◽  
Ohmic Contacts ◽  
Specific Resistance ◽  
Thickness Ratio ◽  
Specific Contact Resistance ◽  
Specific Contact ◽  
P Type

This study shows that a thin Ni film on Al/Ti/4H-SiC metal pads allows to preserve the pad form factor during a 1000 °C/2 min treatment, provided that the Al and Ti film thicknesses are sufficiently thin. Moreover, by reducing the Al to Ti thickness ratio, droplet formation in the contact area is avoided and a mirror-like appearance is obtained. This optimal contact morphology corresponds to a specific contact resistance of few 10-4Ωcm2at room temperature on p-type 4H-SiC with resistivity in the range 0.1 – 1 Ωcm.

Influence of Ni and Nb thickness on low specific contact resistance and high-temperature reliability of ohmic contacts to 4H-SiC

2019 ◽  
Vol 58 (11) ◽  
pp. 116501 ◽  
Author(s):  
Vuong Van Cuong ◽  
Seiji Ishikawa ◽  
Tomonori Maeda ◽  
Hiroshi Sezaki ◽  
Satoshi Yasuno ◽  
...  
Keyword(s):  
High Temperature ◽  
Contact Resistance ◽  
Ohmic Contacts ◽  
Specific Contact Resistance ◽  
Specific Contact

Al/Ni And Al/Ti Ohmic Contact To P-type SiC Diffused Layer

2000 ◽  
Vol 640 ◽  
Author(s):  
Xaiobin Wang ◽  
Stanislav Soloviev ◽  
Ying Gao ◽  
G. Straty ◽  
Tangali Sudarshan ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Specific Contact Resistance ◽  
Metal Contacts ◽  
Transfer Length ◽  
Type Layer ◽  
Transmission Line Method ◽  
Specific Contact ◽  
Background Doping ◽  
P Type

ABSTRACTOhmic contacts to p-type SiC were fabricated by depositing Al/Ni and Al/Ti followed by high temperature annealing. A p-type layer was fabricated by Al or B diffusion from vapor phase into both p-type and n-type substrates. The thickness of the diffused layer was about 0.1–0.2 μm with surface carrier concentration of about 1.0×1019cm−3. Metal contacts to a p-type substrate with a background doping concentration of 1.2×1018cm−3, without a diffusion layer, were also formed. The values of specific contact resistance obtained by Circular Transmission Line Method (CTLM) and Transfer Length Method (TLM) for the n-type substrate, and by Cox & Strack method for p-type substrate, respectively, varied from 1.3×10−4Ωcm2 to 8.8×10−3 Ωcm2. The results indicate that the specific contact resistance could be significantly reduced by creating a highly doped diffused surface layer.

scholarly journals Ohmic contacts to Si-implanted and un-implanted n-type GaN

1995 ◽  
Vol 395 ◽  
Author(s):  
J. Brown ◽  
J Ramer ◽  
K. ZHeng ◽  
L.F. Lester ◽  
S.D. Hersee ◽  
...  
Keyword(s):  
Contact Resistance ◽  
Ohmic Contacts ◽  
Annealing Temperature ◽  
Contact Resistivity ◽  
Contact Structures ◽  
Specific Contact Resistance ◽  
Resistance Variation ◽  
Specific Contact ◽  
Metal Layers ◽  
Nitrogen Vacancies

ABSTRACTWe report on ohmic contacts to Si-implanted and un-implanted n-type GaN on sapphire. A ring shaped contact design avoids the need to isolate the contact structures by additional implantation or etching. Metal layers of Al and Ti/Al were investigated. On un-implanted GaN, post metalization annealing was performed in an RTA for 30 seconds in N2 at temperatures of 700, 800, and 900°C, A minimum specific contact resistance (rc) of 1.4×10−5 Ω-cm2 was measured for Ti/Al at an annealing temperature of 800°C. Although these values are reasonably low, variations of 95% in specific contact resistance were measured within a 500 µm distance on the wafer. These results are most likely caused by the presence of compensating hydrogen. Specific contact resistance variation was reduced from 95% to 10% by annealing at 900°C prior to metalization. On Si-implanted GaN, un-annealed ohmic contacts were formed with Ti/Al metalization. The implant activation anneal of 1120°C generates nitrogen vacancies that leave the surface heavily n-type, which makes un-annealed ohmic contacts with low contact resistivity possible.

TiW/TiWN/Pt Ohmic Contacts to n-Type 3C-SiC

2006 ◽  
Vol 911 ◽  
Author(s):  
Kirk Hofeling ◽  
Loren Rieth ◽  
Florian Solzbacher
Keyword(s):  
Contact Resistance ◽  
Room Temperature ◽  
Ohmic Contacts ◽  
Specific Contact Resistance ◽  
Test Duration ◽  
Capping Layer ◽  
Interface Reactions ◽  
Transmission Line Method ◽  
Specific Contact

AbstractTiW(40 nm)/TiWN(80 nm)/Pt(500nm) was investigated as a new high-temperature compatible contact stack to 3C-SiC for harsh environment applications. Performance of TiW/TiWN/Pt contacts deposited on unintentionally doped (8.85×1018 cm-3) 3C-SiC grown by LPCVD to a thickness of ~1μm on (100) Si are reported. The linear transmission line method was used to determine specific contact resistance (ρc) at room temperature and for long-term tests at 300 °C. As deposited contacts were Ohmic with a ρc range of 1×10-4 to 1×10-3 cm2. These contacts were annealed for five minutes in forming gas (8% H2 92% Ar), at temperatures from 450 to 950 °C and all retained Ohmic character. Annealing samples at 450, 550 and 950 °C decreased ρc while anneling between 650 and 850 °C generally increased ρc.Auger Electron Spectroscopy (AES) analysis was performed on a sample annealed at 750 °C. The as-received surface was composed of Si and O; after a brief sputter etch a characteristic Pt peak became visible and the O peak decreased substantially. Depth profiles detected Si throughout the Pt capping layer but not in the TiW layers. We suspect that Si diffuses from the SiC substrate into the Pt capping layer and surface Si also reacts with O2 to from an oxide. These reactions, in combination with incomplete SiC/TiW interface reactions, are suspected to cause the increase of ρc for samples annealed between 650 and 850 °C. Annealing at 950 °C gave the lowest contact resistance of 2.3×10-5. Long-term testing at 300 °C for 190 hours, in atmosphere, was performed on contacts annealed at 450 °C. When heated, the contacts initial ρc of 2.1×10-4 cm2 increased to ~4×10-3 cm2 which remained stable for the test duration. After long-term testing the sample ρc measured at room temperature decreased to 9.8×10-5 cm2.

Sign in / Sign up

Export Citation Format

Share Document