Evaluation of the insertion torque, implant stability quotient and drilled hole quality for different drill design: an in vitro Investigation

2016 ◽  
Vol 29 (6) ◽  
pp. 656-662 ◽  
Author(s):  
Sergio Alexandre Gehrke ◽  
José Luis Calvo Guirado ◽  
Raphaël Bettach ◽  
Massimo Del Fabbro ◽  
Carlos Pérez-Albacete Martínez ◽  
...  
Keyword(s):  
Insertion Torque ◽  
Implant Stability ◽  
Hole Quality ◽  
Implant Stability Quotient ◽  
In Vitro Investigation ◽  
Drill Design

Effect of Rotating Osteotomes on Primary Implant Stability—An In Vitro Investigation

2013 ◽  
Vol 39 (1) ◽  
pp. 52-57
Author(s):  
Philipp Kreißel ◽  
Felix Kölpin ◽  
Friedrich Graef ◽  
Manfred Wichmann ◽  
Matthias Karl
Keyword(s):  
Bone Density ◽  
Primary Stability ◽  
Surrogate Models ◽  
Poor Quality ◽  
Cortical Layer ◽  
Implant Stability ◽  
Implant Stability Quotient ◽  
Primary Implant ◽  
In Vitro Investigation

Achieving sufficient primary implant stability in poor-quality bone is difficult. Other than for conventional osteotomes, little is known about the effectiveness of screw-shaped spreaders in condensing bone and increasing primary stability. Therefore, implant stability quotient (ISQ) measurements of implants placed in bone surrogate models were conducted. Whereas bony microarchitecture had no effect on implant stability, initial bone density, presence of a cortical layer, and the use of screw-shaped spreaders significantly increased ISQ levels.

Primary Stability of Short Implants Inserted Using Piezoelectric or Drilling Systems: An In Vitro Comparison

2019 ◽  
Vol 45 (4) ◽  
pp. 259-266
Author(s):  
Claudio Stacchi ◽  
Matteo De Biasi ◽  
Lucio Torelli ◽  
Massimo Robiony ◽  
Roberto Di Lenarda ◽  
...  
Keyword(s):  
Cancellous Bone ◽  
Operative Time ◽  
Primary Stability ◽  
Site Preparation ◽  
Preparation Technique ◽  
Implant Stability ◽  
Implant Stability Quotient ◽  
Custom Made ◽  
Implant Site Preparation

The primary objective of the present in vitro study was to evaluate the influence of implant site preparation technique (drills vs ultrasonic instrumentation) on the primary stability of short dental implants with two different designs inserted in simulated low-quality cancellous bone. Eighty implant sites were prepared in custom-made solid rigid polyurethane blocks with two different low cancellous bone densities (5 or 15 pounds per cubic foot [PCF]), equally distributed between piezoelectric (Surgysonic Moto, Esacrom, Italy) and conventional drilling techniques. Two short implant systems (Prama and Syra, Sweden & Martina) were tested by inserting 40 fixtures of each system (both 6.0 mm length and 5.0 mm diameter), divided in the four subgroups (drills/5 PCF density; drills/15 PCF density; piezo/5 PCF density; piezo/15 PCF density). Insertion torque (Ncm), implant stability quotient values, removal torque (Ncm), and surgical time were recorded. Data were analyzed by 3-way ANOVA and Scheffé's test (α = 0.05). With slight variations among the considered dependent variables, overall high primary implant stability was observed across all subgroups. Piezoelectric instrumentation allowed for comparable or slightly superior primary stability in comparison with the drilling procedures in both implant systems. The Prama implants group showed the highest mean reverse torque and Syra implants the highest implant stability quotient values. Piezoelectric implant site preparation took prolonged operative time compared to conventional preparation with drills; among the drilling procedures, Syra system required fewer surgical steps and shorter operative time.

scholarly journals Osseodensification Drilling vs. Standard Protocol of Implant Site Preparation: An In Vitro Study on Polyurethane Foam Sheets

Prosthesis ◽  
2020 ◽  
Vol 2 (2) ◽  
pp. 76-86
Author(s):  
Luca Comuzzi ◽  
Margherita Tumedei ◽  
Adriano Piattelli ◽  
Giovanna Iezzi
Keyword(s):  
Polyurethane Foam ◽  
Cortical Layer ◽  
Polyurethane Foams ◽  
Insertion Torque ◽  
Standard Type ◽  
Removal Torque ◽  
In Vitro Investigation ◽  
Posterior Maxilla ◽  
And Control

(1) Background: The aim of the present in vitro investigation was to evaluate, on polyurethane sheets, two different drilling techniques for dental implant positioning using osteocondensing burs compared to a standard type protocol. (2) Methods: Three different implant designs (Implacil De Bortoli UN III 4 × 10 mm, Restore RBM 4 (HEX) × 10 mm; Implacil De Bortoli UN II 4 × 10 mm) were evaluated (test implant (osteocondensing drills) and control implant (standard drills)). The insertion torque (IT), the removal torque (RT) and the resonance frequency analysis (RFA) values of test and control implants inserted in different size and different density polyurethane foam models were compared for 120 experimental sites. Accordingly, 120 experimental holes were produced in different PCF polyurethane foams: 60 sites were produced in 10 PCF sheets and 60 sites in 10 PCF sheets with an additional 1 mm layer of 30 PCF. (3) Results: The IT, removal torque and RFA values were significantly higher for both of the evaluated implants, in the sites prepared with the osteocondenser drills when compared to sites prepared with standard drills (p < 0.05). The UNII and UN III showed significantly higher stability compared to the HEX implant; these differences increased drastically in the 10 PCF Polyurethane Block with the additional 1 mm cortical layer (p < 0.05). (4) Conclusions: The outcome of this investigation suggested a possible clinical application of osteocondensing burs in case of reduced bone quality and quantity in the posterior maxilla.

scholarly journals Effects of Different Undersizing Site Preparations on Implant Stability

2020 ◽  
Vol 17 (23) ◽  
pp. 8965
Author(s):  
Bernardo Ferreira Lemos ◽  
Paula Lopez-Jarana ◽  
Carlos Falcao ◽  
Blanca Ríos-Carrasco ◽  
Javier Gil ◽  
...  
Keyword(s):  
Primary Stability ◽  
Immediate Loading ◽  
Insertion Torque ◽  
Bovine Bone ◽  
Preparation Technique ◽  
Standard Protocol ◽  
Implant Stability ◽  
Implant Stability Quotient ◽  
Surgical Preparation ◽  
Implant System

As immediate loading protocols are becoming more frequent, the primary stability of implants has become an essential criterion for the osseointegration of dental implants. Based on this, the objective of this study was to understand the influence of different undersized surgical preparation sites on the insertion torque (IT) and implant stability quotient (ISQ). Four different site-preparation protocols were performed on fresh humid type III bovine bone: one control, the standard protocol recommended by the manufacturer (P1), and three variations of undersized techniques (P2, P3 and P4). The implant used was VEGA by Klockner Implant System. The sample size was n = 40 for each of the four groups. A torquemeter was used to measure the IT, and the ISQ was measured with a Penguin RFA. Both variables showed a tendency to increase as the preparation technique was reduced, although not all the values were statistically significant (p < 0.05) when comparing with the standard preparation. The preparations without a cortical drill, P2 and P4, showed better results than those with a cortical drill. Given the limitations of this study, it can be concluded that reducing the implant preparation can increase both the IT and ISQ. Removing the cortical drill is an effective method for increasing implant stability, although it should be used carefully.

An in vitro evaluation on polyurethane foam sheets of the insertion torque, removal torque values, and resonance frequency analysis (RFA) of a self-tapping threads and round apex implant

2020 ◽  
pp. 026248932097179
Author(s):  
Margherita Tumedei ◽  
Adriano Piattelli ◽  
Antonello Falco ◽  
Francesco De Angelis ◽  
Felice Lorusso ◽  
...  
Keyword(s):  
Resonance Frequency ◽  
Dental Implant ◽  
Frequency Analysis ◽  
Insertion Torque ◽  
Resonance Frequency Analysis ◽  
Removal Torque ◽  
In Vitro Investigation ◽  
Posterior Maxilla ◽  
Torque Values

The dental implant primary stability and micromovement absence represent critical factor for dental implant osseointegration. The aim of the present in vitro investigation was to simulate the bone response on different polyurethane densities the effect of self-tapping threads and round apex implant geometry. A total of 40 implants were positioned in D1, D2, D3 and D4 polyurethane block densities following a calibrated drilling protocol. The Insertion, removal Torque and resonance frequency analysis (RFA) means were calculated. All experimental conditions showed insertion torque values >30 Ncm. A significant higher insertion torque, removal and RFA was present in D1 polyurethane. Similar evidences were evidenced for D3 and D4. The effectiveness of the present study suggested a valuable clinical advantage for self-tapping threads and round apex implant using, such as in case of reduced bone density in the posterior maxilla

scholarly journals Does the Osseodensification Technique Allow for the use of a Healing Chamber with Primary Stability in Low-Density Bone? An in Vivo Study

2021 ◽  
Author(s):  
Rafael Coutinho Mello-Machado ◽  
Suelen Cristina Sartoretto ◽  
Jose Mauro Granjeiro ◽  
José Albuquerque Calasans-Maia ◽  
Marcelo Jose Guedes Pinheiro Uzeda ◽  
...  
Keyword(s):  
Bone Remodeling ◽  
Bone Growth ◽  
Primary Stability ◽  
Insertion Torque ◽  
Low Density ◽  
Implant Stability ◽  
Bone Implant ◽  
Implant Stability Quotient ◽  
Implant Bed

Abstract This study aimed to investigate in vivo the hypothesis that the osseodensification technique, through a wider osteotomy, produce healing chambers at the implant-bone interface with no impact on primary stability osseointegration in low-density bone. Twenty implants (3.5 x 10 mm) presenting nanohydroxyapatite (nHA) surface were inserted in the ilium of ten sheep, after preparation of a 2.7-mm wide implant bed with conventional subtractive drilling (SCD) or a 3.8-mm wide implant bed with an osseodensification bur system (OBS) (n = 5/group/period). The final insertion torque (IT) and implant stability quotient (ISQ) evaluated the primary implant stability. After 14 and 28 days, the bone samples containing the implants were processed for histological and histomorphometric evaluation of bone implant contact (BIC) and bone area fraction occupancy (BAFO). No significant differences occurred between the implant bed preparations regarding IT and ISQ (P > 0.05). Histological analysis showed bone remodeling, and bone growth in all samples with no inflammatory infiltrate. BIC values were higher for SCD after 14 and 28 days (p < 0.05), however BAFO values were similar on both groups (p > 0.05). It was possible to conclude that the osseodensification technique allowed a wider implant bed preparation with no prejudice on primary stability and bone remodeling.

scholarly journals Correlation between Insertion Torque and Implant Stability Quotient in Tapered Implants with Knife-Edge Thread Design

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Domenico Baldi ◽  
Teresa Lombardi ◽  
Jacopo Colombo ◽  
Gabriele Cervino ◽  
Giuseppe Perinetti ◽  
...  
Keyword(s):  
Torque Control ◽  
Pairwise Comparisons ◽  
Insertion Torque ◽  
Knife Edge ◽  
Implant Stability ◽  
Implant Stability Quotient ◽  
Significant Difference ◽  
High Torque ◽  
Low Torque ◽  
Implant System

Aim. To evaluate the correlation between insertion torque (IT) and implant stability quotient (ISQ) in tapered implants with knife-edge threads.Methods. Seventy-five identical implants (Anyridge, Megagen) were inserted by using a surgical drilling unit with torque control and an integrated resonance frequency analysis module (Implantmed, W&H). IT (N/cm) and ISQ were recorded and implants were divided into three groups (n=25) according to the IT: low (<30), medium (30 < IT < 50), and high torque (>50). ISQ difference among groups was assessed by Kruskal-Wallis test, followed by Bonferroni-corrected Mann–WhitneyU-test for pairwise comparisons. The strength of the association between IT and ISQ was assessed by Spearman Rho correlation coefficient (α=0.05).Results. At the pairwise comparisons, a significant difference of ISQ values was demonstrated only between low torque and high torque groups. The strength of the association between IT and ISQ value was significant for both the entire sample and the medium torque group, while it was not significant in low and high torque groups.Conclusions. For the investigated implant, ISQ and IT showed a positive correlation up to values around 50 N/cm: higher torques subject the bone-implant system to unnecessary biological and mechanical stress without additional benefits in terms of implant stability. This trial is registered withNCT03222219.

Sign in / Sign up

Export Citation Format

Share Document