Internal curing of blended cement pastes with ultra‐low water‐to‐cement ratio: absorption/desorption kinetics of SAP

2021 ◽  
Author(s):  
Jianhui Liu ◽  
Xianwei Ma ◽  
Caijun Shi ◽  
Sarra Drissi
Keyword(s):  
Blended Cement ◽  
Internal Curing ◽  
Desorption Kinetics ◽  
Cement Pastes ◽  
Cement Ratio ◽  
Water To Cement Ratio ◽  
Kinetics Of

Relative Humidity of Blended Cement Pastes in Sealed during Hydration

2013 ◽  
Vol 539 ◽  
pp. 60-63
Author(s):  
Dan Jin ◽  
Wu Yao ◽  
Yi Chen
Keyword(s):  
Relative Humidity ◽  
Blended Cement ◽  
Mineral Admixture ◽  
Mineral Admixtures ◽  
Cement Pastes ◽  
Cement Ratio ◽  
Water To Cement Ratio ◽  
Cement Based Materials ◽  
Different Ages ◽  
Key Factor

As an important part of cement-based materials，water plays an important role during hydration and self-desiccation so the measurement of relative humidity or internal moisture in the research of cement-based materials is vital. In this paper, the measurement samples are blended cement pastes in sealed with different water to cement ratios and different kind of mineral admixtures. The measurement was taken at different ages during hydration to investigate the changes of relative humidity. The result showed that the water to cement ratio was the key factor of affecting the change of relative humidity, and the effect of mineral admixture kind was not very obvious in this experiment.

Chloride Ingress Control and Promotion of Internal Curing in Concrete Using Superabsorbent Polymer

2021 ◽  
Vol 888 ◽  
pp. 67-75
Author(s):  
Ariel Verzosa Melendres ◽  
Napoleon Solo Dela Cruz ◽  
Araceli Magsino Monsada ◽  
Rolan Pepito Vera Cruz
Keyword(s):  
Compressive Strength ◽  
Cementitious Materials ◽  
Internal Curing ◽  
Mix Design ◽  
Chloride Ingress ◽  
Superabsorbent Polymer ◽  
Cement Slurry ◽  
Chloride Permeability ◽  
Cement Ratio ◽  
Water To Cement Ratio

Chloride ingress into concrete from the surrounding environment can result in the corrosion of the embedded steel reinforcement and cause damage to the concrete. Superabsorbent polymer (SAP) with fine particle size was incorporated into the structure of concrete for controlling the chloride ingress and improving its compressive strength via promotion of internal curing. The SAP used in this study was evaluated for its absorbency property when exposed to cementitious environment such as aqueous solution of Ca (OH)2 and cement slurry. The results were compared to that in sodium chloride solution, the environment where absorbency of most of the SAP found in the market are well studied. Results showed that although SAP absorbency decreased with increasing concentration of Ca (OH)2 and cement, the results suggest that water containing cementitious materials are able to be absorbed by SAP. Chloride ingress into 28-day cured concrete specimens were determined using Rapid Chloride Penetration Test (RCPT) method employing 60V DC driving force. Concrete samples with size of 50 mm height x 100 mm diameter were prepared using a M25 mix design with 0.4 and 0.45 water to cement ratios and different percentages of SAP such as 0.05%, 0.1% and 0.15% with respect to cement mass. Results showed that concrete with 0.15% SAP gave the best result with 14% less chloride permeability than concrete with no SAP for a 0.4 water to cement ratio. Concrete samples for compressive strength tests with size of 200 mm height x 100 mm diameter were prepared using the same mix design and percentages of SAP and cured for 28 days. Results showed that the best results for compressive strength was found at 0.1% SAP at a 0.4 water to cement ratio which can be attributed to internal curing provided by SAP.

scholarly journals Surface Roughness and Porosity of Hydrated Cement Pastes

10.14311/1374 ◽  
2011 ◽  
Vol 51 (3) ◽  
Author(s):  
T. Ficker ◽  
D. Martišek ◽  
H. M. Jennings
Keyword(s):  
The Other ◽  
Porous Solids ◽  
Surface Irregularity ◽  
Hydrated Cement ◽  
Cement Pastes ◽  
Cement Ratio ◽  
Fracture Surfaces ◽  
Water To Cement Ratio ◽  
The One ◽  
Highly Porous

. Seventy-eight graphs were plotted to describe and analyze the dependences of the height and roughness irregularities on the water-to-cement ratio and on the porosity of the cement hydrates. The results showed unambiguously that the water-to-cement ratio or equivalently the porosity of the specimens has a decisive influence on the irregularities of the fracture surfaces of this material. The experimental results indicated the possibility that the porosity or the value of the water-to-cement ratio might be inferred from the height irregularities of the fracture surfaces. It was hypothesized that there may be a similarly strong correlation between porosity and surface irregularity, on the one hand, and some other highly porous solids, on the other, and thus the same possibility to infer porosity from the surfaces of their fracture remnants.

scholarly journals CO2 Curing Efficiency for Cement Paste and Mortars Produced by a Low Water-to-Cement Ratio

Materials ◽  
2020 ◽  
Vol 13 (17) ◽  
pp. 3883
Author(s):  
Seong Ho Han ◽  
Yubin Jun ◽  
Tae Yong Shin ◽  
Jae Hong Kim
Keyword(s):  
Cement Paste ◽  
Pressure Vessel ◽  
Gas Pressure ◽  
Strength Development ◽  
Co2 Uptake ◽  
Cement Pastes ◽  
Co2 Gas ◽  
Cement Ratio ◽  
Mix Proportion ◽  
Water To Cement Ratio

Curing by CO2 is a way to utilize CO2 to reduce greenhouse gas emissions. Placing early-age cement paste in a CO2 chamber or pressure vessel accelerates its strength development. Cement carbonation is attributed to the quickened strength development, and CO2 uptake can be quantitatively evaluated by measuring CO2 gas pressure loss in the pressure vessel. A decrease in CO2 gas pressure is observed with all cement pastes and mortar samples regardless of the mix proportion and the casting method; one method involves compacting a low water-to-cement ratio mix, and the other method comprises a normal mix consolidated in a mold. The efficiency of the CO2 curing is superior when a 20% concentration of CO2 gas is supplied at a relative humidity of 75%. CO2 uptake in specimens with the same CO2 curing condition is different for each specimen size. As the specimen scale is larger, the depth of carbonation is smaller. Incorporating colloidal silica enhances the carbonation as well as the hydration of cement, which results in contributing to the increase in the 28-day strength.

scholarly journals Hydration processes of cement paste-an EPR study

2010 ◽  
Vol 7 (1) ◽  
pp. 215-219
Author(s):  
R. Gopalakrishnan ◽  
D. Govindarajan
Keyword(s):  
Setting Time ◽  
Electron Paramagnetic Resonance Study ◽  
Hydration Time ◽  
Time Intervals ◽  
Paramagnetic Resonance ◽  
Cement Pastes ◽  
Cement Ratio ◽  
Final Setting Time ◽  
Water To Cement Ratio ◽  
Electron Paramagnetic

The present works reports the hydration processes of Portland cement through Electron paramagnetic resonance study. Cement pastes in a Water to cement ratio (W/C) of 0.4 at different hydration time intervals have been prepared. The g-factor of Fe(III) and Mn(II) impurities at different hydration ages has been related to changes in setting time of cement. Both gFe and gMn values are reach a maximum values at final setting time of OPC paste.

Effect of Fly Ash Incorporation on Rheology of Cement Pastes

1986 ◽  
Vol 86 ◽  
Author(s):  
M. Rattanussorn ◽  
D. M. Roy ◽  
R. I. A. Malek
Keyword(s):  
Fly Ash ◽  
Chemical Composition ◽  
Zeta Potential ◽  
Spherical Shape ◽  
Ash Content ◽  
Type I ◽  
Special Effect ◽  
Cement Pastes ◽  
Cement Ratio ◽  
Water To Cement Ratio

ABSTRACTThe predominant spherical shape of fly ash particles combined with mainly glassy composition and texture of its surfaces have a special effect on rheology of cement pastes containing fly ash. The early ages rheological behavior of cement pastes (ASTM Type I) incorporating 30% low-calcium fly ash was monitored by measuring viscosity of the fresh pastes prior to initial hardening and stiffening (up to −2 hours) as a function of time. The viscosities were determined using a co-axial rotoviscometer (HAAKE). The effects of fly ash content, water to cement ratio, and presence and concentration of superplasticizer, were evaluated. In addition, the dispersivity of fly ash spheres was evaluated by determining the zeta-potential of fly ash suspensions in water using a microelectrophoresis technique and the results were correlated to the chemical composition of fly ash as well as the viscosities of fresh pastes.

Use of recycled fine clay brick aggregate as internal curing agent for low water to cement ratio mortar

2020 ◽  
Vol 264 ◽  
pp. 120280
Author(s):  
Zhi Ge ◽  
Yujie Feng ◽  
Hongzhi Zhang ◽  
Jianzhuang Xiao ◽  
Renjuan Sun ◽  
...  
Keyword(s):  
Internal Curing ◽  
Curing Agent ◽  
Clay Brick ◽  
Cement Ratio ◽  
Water To Cement Ratio ◽  
Fine Clay
Sign in / Sign up

Export Citation Format

Share Document