scholarly journals Evaluation of Structural Behavior of Reinforced Concrete Exterior Beam-Column Joints with High-Strength Concrete

2014 ◽  
Vol 18 (6) ◽  
pp. 72-81 ◽  
Author(s):  
Bum-Sik Lee ◽  
Kyung-Duk Kim ◽  
Sang-Woo Kim ◽  
Kil-Hee Kim ◽  
Jung-Yoon Lee
Keyword(s):  
Reinforced Concrete ◽  
High Strength Concrete ◽  
High Strength ◽  
Structural Behavior ◽  
Strength Concrete

Structural Behavior of RC Cylinders Confined with High Strength Transverse Reinforcement

2010 ◽  
Vol 163-167 ◽  
pp. 1321-1324
Author(s):  
Sang A. Cha ◽  
Cho Hwa Moon ◽  
Sang Woo Kim ◽  
Kil Hee Kim ◽  
Jung Yoon Lee
Keyword(s):  
Compressive Strength ◽  
Reinforced Concrete ◽  
Yield Strength ◽  
High Strength Concrete ◽  
High Strength ◽  
Structural Behavior ◽  
Transverse Reinforcement ◽  
Strength Concrete ◽  
High Rise ◽  
Compressive Strength Of Concrete

The number of high-rise reinforced concrete (RC) buildings is steadily increasing since 1980’s. The use of high strength concrete is indispensible for high-rise RC construction to ensure sufficient strength of the structure. The effect of high strength concrete can be significantly improved by the use of high strength and large size reinforcing bars. The yield strength of transverse reinforcement is limited in the current design codes to prevent possible sudden concrete failure due to over reinforcement. This paper presents the effects of the yield strength of transverse reinforcement and compressive strength of concrete on the structural behavior of reinforced concrete cylinders. Two parameters were considered in this investigation: compressive strength of concrete and the yield strength of transverse reinforcement (472MPa, 880MPa, and 1,430 MPa). Analytical and experimental results indicated that the structural behavior of RC cylinders confined with high strength transverse reinforcement is strongly influenced by compressive strength of concrete.

Seismic Performance of High Titanium Heavy Slag High Strength Concrete Columns

2012 ◽  
Vol 174-177 ◽  
pp. 455-459 ◽  
Author(s):  
Xiao Wei Li ◽  
Xue Wei Li ◽  
Xin Yuan
Keyword(s):  
Reinforced Concrete ◽  
Seismic Performance ◽  
High Strength Concrete ◽  
Load Ratio ◽  
High Strength ◽  
Scale Model ◽  
Transverse Reinforcement ◽  
Reinforced Concrete Column ◽  
Displacement Ductility ◽  
Strength Concrete

For expedite the development of high titanium heavy slag concrete, eight high titanium heavy slag high strength reinforced concrete (HTHS-HSRC) scale model column are studied. The eight HTHS-HSRC model columns are tested under reversed horizontal force. Primary experimental parameters include axial load ratio varying from 0.3 to 0.5, volumetric ratios of transverse reinforcement ranging from 1.38% to 1.56%, strength of high titanium heavy slag high strength concrete varying from 55.9 to 61.6 N/mm2 and configurations of transverse reinforcement. It is found from the test result that HTHS-HSRC model columns provides comparable seismic performance to those usually used reinforced concrete column in terms of member ductility, hysteretic and energy dissipation capacity. Primary Factors of Displacement Ductility of Model Columns are also discussed.

Mechanical Properties of HPC and Numerical Simulation of Mine Shaft under 3D Load

2015 ◽  
Vol 777 ◽  
pp. 48-51
Author(s):  
Hui Cao ◽  
Lin Lin Jiang
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
High Strength Concrete ◽  
Effective Strain ◽  
Earth Pressure ◽  
High Strength ◽  
Wall Structure ◽  
Concrete Wall ◽  
Mine Shaft ◽  
Strength Concrete

The mechanical properties of high-strength concrete was studied in the laboratory, and obtained a high strength concrete uniaxial compressive strength changes with curing period, found that low temperature curing C100 Poisson's ratio of concrete is 0.24, and elastic modulus reached about 52.5GPa. The test results are applied to the numerical calculation, established a separate type reinforced concrete wall, and the multiaxial loading the stress state is simulated, the research shows that it is applied to C100 reinforced concrete shaft lining under its own gravity and the surrounding soil earth pressure, the maximum effective stress are respectively 25MPa , and effective strain is 4E-4mm, structure of shaft wall failure caused by shear wall structure. Under the three state of compression, the strength of concrete is improved.

Experimental Studies on High Strength Concrete Beams Reinforced with Steel and GFRP Rebars

2012 ◽  
Vol 238 ◽  
pp. 669-673 ◽  
Author(s):  
Ying Hao Liu ◽  
Yong Yuan
Keyword(s):  
High Strength Concrete ◽  
Experimental Studies ◽  
High Strength ◽  
Fiber Reinforced Polymer ◽  
Structural Behavior ◽  
Strength Concrete ◽  
Reinforced Polymer ◽  
Glass Fiber Reinforced ◽  
Steel Rebars ◽  
Gfrp Rebars

The paper analyzes the structural behavior of high strength concrete (HSC) beams reinforced with hybrid glass fiber reinforced polymer (GFRP) and steel reinforcements. The analysis refers to HSC beams reinforced with GFRP rebars and steel rebars placed in different layers. Results of the experimental and theoretical investigation are represented and discussed. Significant features of the structural behavior regarding flexural strength, deflection, are pointed out.

Sign in / Sign up

Export Citation Format

Share Document