An Experience of Ageing on XLPE Insulation

2013 ◽  
Vol 64 (4) ◽  
Author(s):  
W. G. Ariastina ◽  
A. I. Weking ◽  
I. N. S. Kumara ◽  
I. A. D. Giriantari ◽  
I. N. Sugiarta
Keyword(s):  
Surface Temperature ◽  
Insulation Degradation ◽  
Maintenance Work ◽  
Conductor Temperature ◽  
Potential Losses ◽  
Distribution Feeder ◽  
The Difference ◽  
Post Insulator ◽  
Xlpe Insulation

A case study of ageing on XLPE conductor insulation of 20kV primary distribution feeder is presented in this paper. The insulation degradation mainly occurred around conductor tie where the conductor is attached to the post insulator. A section of distribution feeder with defects on the conductor insulation has been examined for this study. Potential losses due to presence of discharges have been investigated by measuring the difference current at locations of the affected conductor. Temperature measurements of the insulation surface have also been carried out. Provisional maintenance procedures were introduced to eliminate the discharges. Measurements of current and surface temperature were repeated nine months after completion of the maintenance work. Results indicated that the discharges have been completely disappeared.

EVALUASI PROYEKSI DEMAND BARANG DAN PENUMPANG PELABUHAN DI PROVINSI MALUKU

2019 ◽  
Vol 19 (2) ◽  
pp. 101-110
Author(s):  
Adrian Firdaus ◽  
M. Dwi Yoga Sutanto ◽  
Rajin Sihombing ◽  
M. Weldy Hermawan
Keyword(s):  
Time Series ◽  
Projection Method ◽  
Development Plan ◽  
Master Plan ◽  
Port Development ◽  
Loading And Unloading ◽  
The Difference ◽  
Existing Data

Abstract Every port in Indonesia must have a Port Master Plan that contains an integrated port development plan. This study discusses one important aspect in the preparation of the Port Master Plan, namely the projected movement of goods and passengers, which can be used as a reference in determining the need for facilities at each stage of port development. The case study was conducted at a port located in a district in Maluku Province and aims to evaluate the analysis of projected demand for goods and passengers occurring at the port. The projection method used is time series and econometric projection. The projection results are then compared with the existing data in 2018. The results of this study show that the econometric projection gives adequate results in predicting loading and unloading activities as well as the number of passenger arrival and departure in 2018. This is indicated by the difference in the percentage of projection results towards the existing data, which is smaller than 10%. Whereas for loading and unloading activities, time series projections with logarithmic trends give better results than econometric projections. Keywords: port, port master plan, port development, unloading activities  Abstrak Setiap pelabuhan di Indonesia harus memiliki sebuah Rencana Induk Pelabuhan yang memuat rencana pengem-bangan pelabuhan secara terpadu. Studi ini membahas salah satu aspek penting dalam penyusunan Rencana Induk Pelabuhan, yaitu proyeksi pergerakan barang dan penumpang, yang dapat dipakai sebagai acuan dalam penentuan kebutuhan fasilitas di setiap tahap pengembangan pelabuhan. Studi kasus dilakukan pada sebuah pelabuhan yang terletak di sebuah kabupaten di Provinsi Maluku dan bertujuan untuk melakukan evaluasi ter-hadap analisis proyeksi demand barang dan penumpang yang terjadi di pelabuhan tersebut. Metode proyeksi yang dipakai adalah proyeksi deret waktu dan ekonometrik. Hasil proyeksi selanjutnya dibandingkan dengan data eksisting tahun 2018. Hasil studi ini menunjukkan bahwa proyeksi ekonometrik memberikan hasil yang cukup baik dalam memprediksi aktivitas bongkar barang serta jumlah penumpang naik dan turun di tahun 2018. Hal ini diindikasikan dengan selisih persentase hasil proyeksi terhadap data eksisting yang lebih kecil dari 10%. Sedangkan untuk aktivitas muat barang, proyeksi deret waktu dengan tren logaritmik memberikan hasil yang lebih baik daripada proyeksi ekonometrik. Kata-kata kunci: pelabuhan, rencana induk pelabuhan, pengembangan pelauhan, aktivitas bongkar barang

scholarly journals Using a Process Approach to Pandemic Planning: A Case Study

2021 ◽  
Vol 11 (9) ◽  
pp. 4121
Author(s):  
Hana Tomaskova ◽  
Erfan Babaee Tirkolaee
Keyword(s):  
Process Model ◽  
Process Mining ◽  
Process Approach ◽  
Research Topic ◽  
Future Research ◽  
Critical Situation ◽  
Pandemic Planning ◽  
The Difference ◽  
Smart Technologies

The purpose of this article was to demonstrate the difference between a pandemic plan’s textual prescription and its effective processing using graphical notation. Before creating a case study of the Business Process Model and Notation (BPMN) of the Czech Republic’s pandemic plan, we conducted a systematic review of the process approach in pandemic planning and a document analysis of relevant public documents. The authors emphasized the opacity of hundreds of pages of text records in an explanatory case study and demonstrated the effectiveness of the process approach in reengineering and improving the response to such a critical situation. A potential extension to the automation and involvement of SMART technologies or process optimization through process mining techniques is presented as a future research topic.

Ocular surface temperature differences in glaucoma

2021 ◽  
pp. 112067212110237
Author(s):  
Ari Leshno ◽  
Ori Stern ◽  
Yaniv Barkana ◽  
Noa Kapelushnik ◽  
Reut Singer ◽  
...  
Keyword(s):  
Surface Temperature ◽  
Thermal Imaging ◽  
Ocular Surface ◽  
Open Angle Glaucoma ◽  
Tissue Temperature ◽  
Body Temperatures ◽  
Current Thinking ◽  
Imaging Camera ◽  
The Mean ◽  
The Difference

Purpose: Accumulating evidence suggests that neuroinflammation and immune response are part of the sequence of pathological events leading to optic nerve damage in glaucoma. Changes in tissue temperature due to inflammation can be measured by thermographic imaging. We investigated the ocular surface temperature (OST) profile of glaucomatous eyes to better understand the pathophysiology of these conditions. Methods: Subjects diagnosed with glaucoma (primary open angle glaucoma [POAG] or pseudo exfoliation glaucoma [PXFG]) treated at the Sam Rothberg Glaucoma Center (11/2019–11/2020.) were recruited. Healthy subjects with no ocular disease served as controls. The Therm-App thermal imaging camera was used for OST acquisition. Room and body temperatures were recorded, and the mean temperatures of the medial cantus, lateral cantus, and cornea were calculated with image processing software. Results: Thermographic images were obtained from 52 subjects (52 eyes: 25 POAG and 27 PXFG) and 66 controls (66 eyes). Eyes with glaucoma had a significantly higher OST compared to controls (mean 0.9 ± 0.3°C, p < 0.005). The difference between the two groups remained significant after adjustment for age, sex, intraocular pressure (IOP) and room and body temperatures. Lens status and topical IOP-lowering medication did not significantly affect OST. A subgroup analysis revealed that the OST was higher among eyes with POAG compared to eyes with PXFG, but not significantly. Conclusions: Differences in the OST between glaucomatous and normal eyes strengthens current thinking that inflammation affects the pathophysiology of glaucoma. Longitudinal studies are warranted to establish the prognostic value of thermographic evaluations in these patients.

scholarly journals The Value of a Decrease in Temperature by One Degree Celsius of the Regional Microclimate—The Cooling Effect of the Paddy Field

Atmosphere ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 353
Author(s):  
Ya-Wen Chiueh ◽  
Chih-Hung Tan ◽  
Hsiang-Yi Hsu
Keyword(s):  
Land Use ◽  
Surface Temperature ◽  
Paddy Field ◽  
Research Area ◽  
Paddy Fields ◽  
Cooling Effect ◽  
Field Temperature ◽  
Bare Land ◽  
The Face ◽  
The Difference

In the face of climate change, extreme climates are becoming more frequent. There were severe droughts in Taiwan in 2020, 2014–2015, and 2002. In these years, the paddy fields were kept fallow to save water and transfer agricultural water to non-agricultural use. On the other hand, with global warming, the existence of paddy fields may be one of the natural solutions to regional temperature mitigation. This study used remote sensing to quantify the difference in temperature between paddy fields and urban areas. The result of overall surface temperature deductive analysis revealed that the temperature in the whole Taoyuan research area was 1.2 °C higher in 2002 than in 2003 because of fallowing of the paddy field, while in the Hsinchu research area, it was 1.5 °C higher in 2002 than in 2003, due to the same reason described above. In terms of the difference in land use, for the Hsinchu research area, the surface temperature deductive result showed that the average paddy field temperature in 2002 was 22.3 °C (sample area average), which was 7.7 °C lower than that of the building and road point and 4.3 °C lower than that of the bare land point. The average paddy field temperature in 2003 was 19.2 °C (sample area average), which was 10.1 °C lower than that of the building and road point and 8.3 °C lower than that of the bare land point. Then this study evaluated the economic valuation of the paddy field cooling effect using the contingent valuation method. Through the paddy field cooling effect and in the face of worsening extreme global climate, the willingness to pay (WTP) of the respondents in Taiwan for a decrease of 1 °C with regard to the regional microclimate was evaluated. It was found that people in Taiwan are willing to pay an extra 8.89 USD/per kg rice/year for the paddy for a decrease in temperature by 1 °C in the regional microclimate due to the paddy field. Furthermore, this study applied the benefits transfer method to evaluate the value of a decrease of 1 °C in the regional microclimate in Taiwan. The value of a decrease of 1 °C in the regional microclimate in Taiwan is 9,693,144,279 USD/year. In this regard, the economic value of 1 °C must not be underestimated. In conclusion, more caution is needed while making decisions to change the land use of paddy fields to other land uses.

scholarly journals E-learning-Oriented Software Architecture Design and Case Study

2015 ◽  
Vol 10 (4) ◽  
pp. 59
Author(s):  
Peng Lu ◽  
Xiao Cong ◽  
Dongdai Zhou
Keyword(s):  
Software Architecture ◽  
Building Blocks ◽  
Domain Model ◽  
Learning System ◽  
Application Framework ◽  
Component Library ◽  
E Learning ◽  
The Difference ◽  
High Level

Nowadays, E-learning system has been widely applied to practical teaching. It was favored by people for its characterized course arrangement and flexible learning schedule. However, the system does have some problems in the process of application such as the functions of single software are not diversified enough to satisfy the requirements in teaching completely. In order to cater more applications in the teaching process, it is necessary to integrate functions from different systems. But the difference in developing techniques and the inflexibility in design makes it difficult to implement. The major reason of these problems is the lack of fine software architecture. In this article, we build domain model and component model of E-learning system and components integration method on the basis of WebService. And we proposed an abstract framework of E-learning which could express the semantic relationship among components and realize high level reusable on the basis of informationized teaching mode. On this foundation, we form an E-learning oriented layering software architecture contain component library layer, application framework layer and application layer. Moreover, the system contains layer division multiplexing and was not built upon developing language and tools. Under the help of the software architecture, we could build characterized E-learning system flexibly like building blocks through framework selection, component assembling and replacement. In addition, we exemplify how to build concrete E-learning system on the basis of this software architecture.

Magnetotelluric static shift: Estimation and removal using the cokriging method

Geophysics ◽  
2007 ◽  
Vol 72 (1) ◽  
pp. F25-F34 ◽  
Author(s):  
Benoit Tournerie ◽  
Michel Chouteau ◽  
Denis Marcotte
Keyword(s):  
Apparent Resistivity ◽  
A Priori ◽  
Shift Factor ◽  
Static Shift ◽  
Geostatistical Model ◽  
Data Set ◽  
Resistivity Sounding ◽  
The Difference ◽  
Cross Variogram

We present and test a new method to correct for the static shift affecting magnetotelluric (MT) apparent resistivity sounding curves. We use geostatistical analysis of apparent resistivity and phase data for selected periods. For each period, we first estimate and model the experimental variograms and cross variogram between phase and apparent resistivity. We then use the geostatistical model to estimate, by cokriging, the corrected apparent resistivities using the measured phases and apparent resistivities. The static shift factor is obtained as the difference between the logarithm of the corrected and measured apparent resistivities. We retain as final static shift estimates the ones for the period displaying the best correlation with the estimates at all periods. We present a 3D synthetic case study showing that the static shift is retrieved quite precisely when the static shift factors are uniformly distributed around zero. If the static shift distribution has a nonzero mean, we obtained best results when an apparent resistivity data subset can be identified a priori as unaffected by static shift and cokriging is done using only this subset. The method has been successfully tested on the synthetic COPROD-2S2 2D MT data set and on a 3D-survey data set from Las Cañadas Caldera (Tenerife, Canary Islands) severely affected by static shift.

scholarly journals Structure of Urban Landscape and Surface Temperature: a Case Study in Philadelphia, PA

2020 ◽  
Author(s):  
Erik Mitz ◽  
Peleg Kremer ◽  
Neele Larondelle ◽  
Justin Stewart
Keyword(s):  
Surface Temperature ◽  
Urban Landscape

Identification of asset life cycle stage: case study in heavy-duty truck fleet

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Oscar Daniel Rivera Baena ◽  
Maria Valentina Clavijo Mesa ◽  
Carmen Elena Patino Rodriguez ◽  
Fernando Jesus Guevara Carazas
Keyword(s):  
Life Cycle ◽  
Design Methodology ◽  
Life Cycle Stage ◽  
Waste Collection ◽  
Content Type ◽  
Heavy Duty Truck ◽  
Maintenance Work ◽  
Operational Decision Making ◽  
The Moment

PurposeThis paper aims to determine the stage of the life cycle where the trucks of a waste collection fleet from a Colombian city are located through a reliability approach. The reliability analysis and the evaluation of curve of operational costs allow to know the moment in which it is necessary to make decisions regarding an asset, its maintenance or possible replacement.Design/methodology/approachFor a dataset presented as maintenance work orders, the time to failures (TTFs) for each vehicle in the fleet were calculated. Then, a probability density function for those TTFs was fitted to locate each vehicle in a region of the bathtub curve and to calculate the reliability of the whole fleet. A general functional analysis was also developed to understand the function of the vehicles.FindingsIt was possible to determine that the largest proportion of the fleet was in the final stage of the life cycle, in this sense, the entire fleet represent critical assets which in most of cases could be worth replacement or overhaul.Originality/valueIn this study, an address is exposed for the identification of critical equipment by reliability and statistical analysis. This analysis is also integrated with the maintenance management process. This is a broadly interested topic since it allows to support the maintenance and operational decision-making process, indicating the focus of resource allocation all over the entire asset life cycle.

Sign in / Sign up

Export Citation Format

Share Document