Hybrid Vibration Absorption by Zero/Pole-Assignment

1999 ◽  
Vol 122 (4) ◽  
pp. 466-469 ◽  
Author(s):  
Jing Yuan
Keyword(s):  
Transfer Function ◽  
Closed Loop ◽  
Pole Assignment ◽  
Relative Degree ◽  
Vibration Absorber ◽  
Primary System ◽  
Minimum Phase ◽  
Dynamic Vibration Absorber ◽  
Vibration Absorption ◽  
System A

This paper presents a hybrid dynamic vibration absorber (HDVA) that is able to assign tunable zeros and poles to a closed-loop primary system. A detailed procedure is presented to design the HDVA and match closed-loop response of a primary system to a prototype transfer function, subject to a modest constraint that the prototype is minimum-phase with relative degree 2. [S0739-3717(00)00103-3]

scholarly journals Attenuation of Motorcycle Handle Vibration Using Dynamic Vibration Absorber

2018 ◽  
Vol 217 ◽  
pp. 01006
Author(s):  
Muhammad Iyad Al-Maliki Saifudin ◽  
Nabil Mohamad Usamah ◽  
Zaidi Mohd Ripin
Keyword(s):  
Vibration Absorber ◽  
Primary System ◽  
Additional Source ◽  
Dynamic Vibration Absorber ◽  
Vibration Absorption ◽  
The Road ◽  
Dynamic Vibration ◽  
Attenuation Level ◽  
Road Surface Roughness ◽  
Extended Exposure

Motorcycle riders are exposed to hand-transmitted vibration of the hand-arm system due to the vibration of the handle and extended exposure can result in numbness and trembling. One feasible solution to attenuate the handle vibration is by using a dynamic vibration absorber (DVA). In this work a DVA is designed and mounted on the motorcycle handle in order to reduce the vibration at the handle by transferring the vibration from the primary system handle to the secondary mass. Removal of elastomeric material at the DVA mounting locations, symmetry of secondary mass and the direction of DVA attachment influence the vibration absorption. A series of tests conducted show that the vibration on the handle is mainly induced by the engine and there is additional source of vibration from the road surface roughness. Installation of DVA at different locations on the handle resulted in various attenuation levels at different speed in the x and z directions. the attenuation level is between 59-68 % in the biodynamic x-directions for speed at 30-50 kmh-1.

Optimal design of inerter-based isolators minimizing the compliance and mobility transfer function versus harmonic and random ground acceleration excitation

2020 ◽  
pp. 107754632094017
Author(s):  
Marcial Baduidana ◽  
Aurelien Kenfack-Jiotsa
Keyword(s):  
Transfer Function ◽  
Vibration Absorber ◽  
Engineering Practice ◽  
Primary System ◽  
Optimal Parameters ◽  
Dynamic Vibration Absorber ◽  
Ground Acceleration ◽  
Dynamic Vibration ◽  
Optimum Parameters ◽  
Peak Value

This study is concerned with the problem of analysis and optimization of inerter-based systems. A main inerter system is generally composed of an inerter, a spring, and viscous damper. Series – parallel inerter system s and series inerter system s are two commonly used configurations of inerter-based system s . First , in this study , the H∞ optimum parameters of inerter-based isolators are derived to minimize the compliance and mobility transfer function of a single-degree -of-freedom system under a harmonic ground acceleration excitation. Under the optimum tuning condition, it is shown that the proposed inerter-based isolators when compared with the traditional dynamic vibration absorber provide larger suppression of the peak value of the magnitude of compliance and mobility transfer function s of the primary system. For the studied cases, more than 40% and 45% improvement can be attained in terms of minimizing the compliance and mobility transfer function s , respectively, as compared with the traditional dynamic vibration absorber for the series – parallel inerter system and 15% and 11% improvement can be attained respectively , for the series inerter system . Finally, further comparison between the inerter-based isolators and traditional dynamic vibration absorber under white noise excitation also shows that the series – parallel inerter system and series inerter system s are superior to the traditional dynamic vibration absorber . The results of the studied systems show that m ore than 23% and 16% improvement are attained in terms of minimizing the compliance and mobility transfer function s respectively , as compared with the traditional dynamic vibration absorber for the series – parallel inerter system and 26% and 13% improvement can be attained respectively , for the series inerter system . The optimal parameters for different cases are obtained. It is shown that the optimal parameters obtained using the minimized mobility transfer function are smaller than those using the compliance transfer function at all mass ratios or inertance-to-mass ratio. The results of this study can provide theoretical basis for design of the optimal inerter-based isolators in engineering practice.

The Influence Region Analysis for the Delayed Resonator Vibration Absorber

2001 ◽  
Author(s):  
Giulio Grillo ◽  
Nejat Olgac
Keyword(s):  
Vibration Suppression ◽  
Vibration Absorber ◽  
Primary System ◽  
Frequency Interval ◽  
Vibration Absorption ◽  
Region Analysis ◽  
The Common ◽  
Resonator Vibration ◽  
Three Degree Of Freedom ◽  
Tuned Vibration Absorber

Abstract This paper presents an influence region analysis for an actively tuned vibration absorber, the Delayed Resonator (DR). DR is shown to respond to tonal excitations with time varying frequencies [1–3]. The vibration suppression is most effective at the point of attachment of the absorber to the primary structure. In this study we show that proper feedback control on the absorber can yield successful vibration suppression at points away from this point of attachment. The form and the size of such “influence region” strongly depend on the structural properties of the absorber and the primary system. There are a number of questions addressed in this paper: a) Stability of vibration absorption, considering that a single absorber is used to suppress oscillations at different locations. b) Possible common operating frequency intervals in which the suppression can be switched from one point on the structure to the others. A three-degree-of-freedom system is taken for as example case. One single DR absorber is demonstrated to suppress the oscillations at one of the three masses at a given time. Instead of an “influence region” a set of “influence points” is introduced. An analysis method is presented to find the common frequency interval in which the DR absorber operates at all three influence points.

Vibration Isolation of the Quarter Car Model of Road Vehicle System using Dynamic Vibration Absorber

2020 ◽  
Vol 12 (5) ◽  
Author(s):  
Sakshi Sharma ◽  
Rakesh Chandmal Sharma ◽  
Sunil Kumar Sharma ◽  
Neeraj Sharma ◽  
Srihari Palli ◽  
...  
Keyword(s):  
Transfer Function ◽  
Vibration Isolation ◽  
Vibration Absorber ◽  
Dynamic Vibration Absorber ◽  
Road Vehicle ◽  
Quarter Car Model ◽  
Car Model ◽  
Dynamic Vibration ◽  
Vehicle System ◽  
Quarter Car

In cases where the natural frequencies of vibrations of a vehicle system are closed to the excitation frequencies from the road surface, dynamic vibration absorber provides the vibration isolation by shifting the resonant frequencies of the system. In the present work, the performance of a dynamic vibration absorber is evaluated with two degrees of freedom quarter car model of a road vehicle system when excited with deterministic inputs. The transmissibility of vibrations from the track to the sprung mass, the transfer function of sprung mass acceleration, the transfer function of suspension deflection and the transfer function of tire deflection is determined.

scholarly journals A PROCEDURE FOR OPTIMAL DESIGN OF A DYNAMIC VIBRATION ABSORBER INSTALLED IN THE DAMPED PRIMARY SYSTEM BASED ON TAGUCHI’S METHOD

2018 ◽  
Vol 56 (5) ◽  
Author(s):  
Nguyen Van Khang
Keyword(s):  
Optimal Design ◽  
Vibration Absorber ◽  
Primary System ◽  
Taguchi’S Method ◽  
Optimal Parameters ◽  
Dynamic Vibration Absorber ◽  
Dynamic Vibration ◽  
Comparison Results

The dynamic vibration absorber (DVA) has been widely applied in various technical fields. This paper presents a  procedure for designing the optimal parameters of  a dynamic vibration absorber attached to a damped primary system. The values of the optimal parameters of the DVA obtained by the Taguchi’s method are compared by the results obtained by other methods. The comparison results show the advantages of the procedure presented in this study

scholarly journals Design of a hybrid proportional electromagnetic dynamic vibration absorber for control of idling engine vibration

2019 ◽  
Vol 234 (1) ◽  
pp. 56-70
Author(s):  
Tao Fu ◽  
Subhash Rakheja ◽  
Wen-Bin Shangguan
Keyword(s):  
Magnetic Force ◽  
Element Model ◽  
Geometric Parameters ◽  
Vibration Absorber ◽  
Electromagnetic Actuator ◽  
Primary System ◽  
Frequency Range ◽  
Dynamic Vibration Absorber ◽  
Dynamic Vibration ◽  
Engine Vibration

A hybrid proportional electromagnetic dynamic vibration absorber consisting of an electromagnetic actuator and an elastic element is proposed for control of engine vibration during idling. The design of the proportional electromagnetic actuator is realized considering the geometric parameters of the core to achieve nearly constant magnetic force over a broad range of its dynamic displacement but proportional to square of the current. The dynamic characteristics of the electromagnetic dynamic vibration absorber are analyzed analytically and experimentally. The effects of various geometric parameters of the actuator such as the slopes and width/height, and the air gaps on the resulting magnetic force characteristics are evaluated using a finite element model and verified experimentally. A methodology is proposed to achieve magnetic force proportional to current and consistent with the disturbance frequency. The hybrid proportional electromagnetic dynamic vibration absorber is subsequently applied to a single-degree-of-freedom primary system with an acceleration feedback control algorithm for attenuation of primary system vibration in a frequency band around the typical idling vibration frequencies. The effectiveness of the hybrid proportional electromagnetic dynamic vibration absorber is evaluated through simulations and laboratory experiments under harmonic excitations in the 20–30 Hz frequency range. Both the simulation and measurements show that the hybrid proportional electromagnetic dynamic vibration absorber can yield effective attenuation of periodic idling vibration in the frequency range considered.

Optimal Design of an Inerter-Based Dynamic Vibration Absorber Connected to Ground

2019 ◽  
Vol 141 (5) ◽  
Author(s):  
Shaoyi Zhou ◽  
Claire Jean-Mistral ◽  
Simon Chesne
Keyword(s):  
Fixed Point ◽  
Optimal Design ◽  
Transient Response ◽  
Damping Ratio ◽  
Vibration Absorber ◽  
Practical Implementation ◽  
Primary System ◽  
Dynamic Vibration Absorber ◽  
Dynamic Vibration ◽  
The Stability

Abstract This paper addresses the optimal design of a novel nontraditional inerter-based dynamic vibration absorber (NTIDVA) installed on an undamped primary system of single degree-of-freedom under harmonic and transient excitations. Our NTIDVA is based on the traditional dynamic vibration absorber (TDVA) with the damper replaced by a grounded inerter-based mechanical network. Closed-form expressions of optimal parameters of NTIDVA are derived according to an extended version of fixed point theory developed in the literature and the stability maximization criterion. The transient response of the primary system is optimized when the coupled system becomes defective, namely having three pairs of coalesced conjugate poles, the proof of which is also spelt out in this paper. Moreover, the analogous relationship between NTIDVA and electromagnetic dynamic vibration absorber is highlighted, facilitating the practical implementation of the proposed absorber. Finally, numerical studies suggest that compared with TDVA, NTIDVA can decrease the peak vibration amplitude of the primary system and enlarge the frequency bandwidth of vibration suppression when optimized by the extended fixed point technique, while the stability maximization criterion shows an improved transient response in terms of larger modal damping ratio and accelerated attenuation rate.

Damping of vibration of the car suspension at resonance

2021 ◽  
pp. 3-8
Author(s):  
Keyword(s):  
Mathematical Model ◽  
Block Diagram ◽  
Vibration Absorber ◽  
Optimal Parameters ◽  
Dynamic Vibration Absorber ◽  
Vibration Absorption ◽  
Dynamic Vibration ◽  
Car Suspension ◽  
Dynamic Damping ◽  
Dynamic Absorber

A block diagram of the device has been developed, which is based on the principle of dynamic vibration absorption. The design of a dynamic absorber of car suspension vibrations is considered. A mathematical model of a car suspension with a dynamic vibration absorber and the results of its numerical simulation are presented. The analysis of the results obtained makes it possible to determine the optimal parameters of the device for a dynamic vibration absorber. Keywords: suspension, car, dynamic, damping, vibration, mathematical, model, analysis, parameters

Sign in / Sign up

Export Citation Format

Share Document