Rotordynamic Coefficients for a Tooth-on-Stator Labyrinth Seal at 70 Bar Supply Pressures: Measurements Versus Theory and Comparisons to a Hole-Pattern Stator Seal

2004 ◽  
Vol 127 (4) ◽  
pp. 843-855 ◽  
Author(s):  
Arthur Picardo ◽  
Dara W. Childs
Keyword(s):  
Control Volume ◽  
Labyrinth Seal ◽  
Test Results ◽  
Flow Models ◽  
Rotordynamic Coefficients ◽  
Volume Model ◽  
Supply Pressure ◽  
Theoretical Predictions ◽  
The One ◽  
Rotor Dynamic

Rotor dynamic and leakage coefficients are presented for a labyrinth seal that was tested at a supply pressure of 70 bar-a and speeds up to 20,200 rpm. Tests were conducted at clearances of 0.1 mm and 0.2 mm, pressure ratios of 0.10, 0.31, and 0.52, and three preswirls ratios. Comparisons are made between test data and predictions from one-control-volume and two-control-volume bulk-flow models. Generally, theoretical predictions agree poorly with the test results, with the one-control volume model giving better predictions. The one-control-volume model provides a conservative prediction for effective damping; i.e., this parameter is underestimated. Both models under predict leakage rates. Comparisons are also made between rotordynamic coefficients of labyrinth and hole-pattern seals.

Rotordynamic Coefficients for a Tooth-on-Stator Labyrinth Seal at 70 Bar Supply Pressures — Measurements Versus Theory and Comparisons to a Hole-Pattern Stator Seal

2004 ◽  
Author(s):  
Arthur Picardo ◽  
Dara W. Childs
Keyword(s):  
Test Data ◽  
Control Volume ◽  
Labyrinth Seal ◽  
Test Results ◽  
Flow Models ◽  
Rotordynamic Coefficients ◽  
Volume Model ◽  
Supply Pressure ◽  
Theoretical Predictions ◽  
The One

Rotordynamic and leakage coefficients are presented for a labyrinth seal that was tested at a supply pressure of 70 bar-a and speeds up to 20200 rpm. Tests were conducted at clearances of 0.1mm and 0.2mm, pressure ratios of 0.10, 0.31 and 0.52, and three pre-swirls ratios. Comparisons are made between test data and predictions from one-control-volume and two-control-volume bulk-flow models. Generally, theoretical predictions agree poorly with the test results, with the one-control volume model giving better predictions. The one-control-volume model provides a conservative prediction for effective damping; i.e., this parameter is underestimated. Both models under predict leakage rates. Comparisons are also made between rotordynamic coefficients of labyrinth and hole-pattern seals.

A Comparison of Experimental Results and Theoretical Predictions for the Rotordynamic Coefficients of Short (L/D = 1/6) Labyrinth Seals

1991 ◽  
Author(s):  
Joseph M. Pelletti ◽  
Dara W. Childs
Keyword(s):  
Flow Model ◽  
Control Volume ◽  
Pressure Ratio ◽  
Experimental Results ◽  
Rotor Speed ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Supply Pressure ◽  
Test Conditions ◽  
Theoretical Predictions

Abstract Experimental results for the rotordynamic coefficients of short (L/D = 1/6) teeth-on-stator and teeth-on-rotor labyrinth seals are presented. The effects that pressure ratio (fluid density), rotor speed, fluid pre-swirl and seal clearance have on these coefficients are studied. Tests were run out to speeds of 16000 rpm with a supply pressure of 17.3 bar and seal clearances ranging from 0.229–0.419 mm. The experimental results are compared with theoretical predictions of a two control volume compressible flow model. The experimental results show that decreases in pressure ratio and increases in rotor speed are stabilizing while increases in fluid pre-swirl and seal clearance are destabilizing for both seal configurations. The theoretical model correctly predicts the effects of pressure ratio, rotor speed and fluid pre-swirl on the cross-coupled stiffness. It also predicts reasonable values for direct damping for all test conditions. However, the theory incorrectly predicts the effect of seal clearance on these coefficients. Consequently the theoretical predictions are much better for the large clearance seals.

Experimental Results for Labyrinth Gas Seals With Honeycomb Stators: Comparisons to Smooth-Stator Seals and Theoretical Predictions

1989 ◽  
Vol 111 (1) ◽  
pp. 161-168 ◽  
Author(s):  
Larry Hawkins ◽  
Dara Childs ◽  
Keith Hale
Keyword(s):  
Flow Model ◽  
Control Volume ◽  
Labyrinth Seal ◽  
Experimental Results ◽  
Test Results ◽  
Labyrinth Seals ◽  
Model Predictions ◽  
Theoretical Predictions ◽  
Gas Seals ◽  
Stiffness And Damping

Experimental measurements are presented for the rotordynamic stiffness and damping coefficients of a teeth-on-rotor labyrinth seal with a honeycomb stator. Inlet circumferential velocity, inlet pressure, rotor speed, and seal clearance are primary variables. Results are compared to (a) data for teeth-on-rotor labyrinth seals with smooth stators, and (b) analytical predictions from a two-control-volume compressible flow model. The experimental results show that the honeycomb-stator configuration is more stable than the smooth-stator configuration at low rotor speeds. At high rotor speeds, the stator surface does not affect stability. The theoretical model predicts the cross-coupled stiffness of the honeycomb-stator seal correctly within 25 percent of measured values. The model provides accurate predictions of direct damping for large clearance seals; however, the model predictions and test results diverge with increasing running speed. Overall, the model does not perform as well for low clearance seals as for high clearance seals.

Theory Versus Experiment for the Rotordynamic Coefficients of Labyrinth Gas Seals: Part I—A Two Control Volume Model

1988 ◽  
Vol 110 (3) ◽  
pp. 270-280 ◽  
Author(s):  
Joseph K. Scharrer
Keyword(s):  
Pressure Distribution ◽  
Control Volume ◽  
Reaction Force ◽  
Labyrinth Seal ◽  
Wall Friction ◽  
Small Motion ◽  
First Order ◽  
Rotordynamic Coefficients ◽  
Volume Model ◽  
Gas Seals

The basic equations are derived for a two-control-volume model for compressible flow in a labyrinth seal. The recirculation velocity in the cavity is incorporated into the model for the first time. The flow is assumed to be completely turbulent and isoenergetic. The wall friction factors are determined using the Blasius formula. Jet flow theory is used for the calculation of the recirculation velocity in the cavity. Linearized zeroth and first-order perturbation equations are developed for small motion about a centered position by an expansion in the eccentricity ratio. The zeroth-order pressure distribution is found by satisfying the leakage equation while the circumferential velocity distribution is determined by satisfying the momentum equations. The first-order equations are solved by a separation of variable solution. Integration of the resultant pressure distribution along and around the seal defines the reaction force developed by the seal and the corresponding dynamic coefficients.

Rotordynamic Coefficients of Labseals for Turbines: Comparing CFD Results With Experimental Data on a Comb-Grooved Labyrinth

2005 ◽  
Author(s):  
Joachim Schettel ◽  
Martin Deckner ◽  
Klaus Kwanka ◽  
Bernd Lu¨neburg ◽  
Rainer Nordmann
Keyword(s):  
Stokes Equations ◽  
Labyrinth Seal ◽  
Navier Stokes ◽  
Test Rig ◽  
Navier Stokes Equations ◽  
Detailed Model ◽  
Identification Methods ◽  
Rotating Speed ◽  
Flow Models ◽  
Rotordynamic Coefficients

The main goal of this paper is to improve identification methods for rotordynamic coefficients of labseals for turbines. This aim was achieved in joint effort of the Technische Universita¨t Mu¨nchen, working on experimental identification methods for rotordynamic coefficients, the University of Technology, Darmstadt, working on prediction methods, and Siemens AG, realizing the results. The paper focuses on a short comb-grooved labyrinth seal. Short labseals, amongst others the above mentioned comb-grooved labyrinth, were examined. by means of a very accurately measuring test rig. The rotor was brought into statically eccentric positions relative to the stator, in order to measure the circumferential pressure distribution as a function of pressure, rotating speed and entrance swirl. The data collected were used to validate results obtained with a numerical method. The theoretical approach is based on a commercial CFD tool, which solves the Navier Stokes equations using numerical methods. As a result, a detailed model of the flow within the test rig is produced. The efforts of computation here are greater than when compared with the likewise wide-spread Bulk flow models, however improved accuracy and flexibility is expected. As the validation of the model is successful, it could then be used to gain further insight in the flow within the seal, and to understand the results better. This showed that rotordynamic coefficients of labseals gained from different test rigs are not necessarily comparable.

Impact of Frequency Dependence of Gas Labyrinth Seal Rotordynamic Coefficients on Centrifugal Compressor Stability

2010 ◽  
Author(s):  
Giuseppe Vannini ◽  
Manish R. Thorat ◽  
Dara W. Childs ◽  
Mirko Libraschi
Keyword(s):  
Molecular Weight ◽  
Numerical Model ◽  
Control Volume ◽  
Labyrinth Seal ◽  
Labyrinth Seals ◽  
Frequency Dependent ◽  
Rotordynamic Coefficients ◽  
Frequency Independent ◽  
Rotor Surface ◽  
Independent Model

A numerical model developed by Thorat & Childs [1] has indicated that the conventional frequency independent model for labyrinth seals is invalid for rotor surface velocities reaching a significant fraction of Mach 1. A theoretical one-control-volume (1CV) model based on a leakage equation that yields a reasonably good comparison with experimental results is considered in the present analysis. The numerical model yields frequency-dependent rotordynamic coefficients for the seal. Three real centrifugal compressors are analyzed to compare stability predictions with and without frequency-dependent labyrinth seal model. Three different compressor services are selected to have a comprehensive scenario in terms of pressure and molecular weight (MW). The molecular weight is very important for Mach number calculation and consequently for the frequency dependent nature of the coefficients. A hydrogen recycle application with MW around 8, a natural gas application with MW around 18, and finally a propane application with molecular weight around 44 are selected for this comparison. Useful indications on the applicability range of frequency dependent coefficients are given.

scholarly journals Annular Honeycomb Seals: Test Results for Leakage and Rotordynamic Coefficients; Comparisons to Labyrinth and Smooth Configurations

1989 ◽  
Vol 111 (2) ◽  
pp. 293-300 ◽  
Author(s):  
D. Childs ◽  
D. Elrod ◽  
K. Hale
Keyword(s):  
Labyrinth Seal ◽  
Test Results ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Stiffness Coefficients ◽  
Shaft Rotation ◽  
Honeycomb Seal ◽  
Cell Dimensions ◽  
Honeycomb Seals ◽  
Rotordynamic Coefficient

Test results are presented for leakage and rotordynamic coefficients for seven honeycomb seals. All seals have the same radius, length, and clearance; however, the cell depths and diameters are varied. Rotordynamic data, which are presented, consist of the direct and cross-coupled stiffness coefficients and the direct damping coefficients. The rotordynamic-coefficient data show a considerable sensitivity to changes in cell dimensions; however, no clear trends are identifiable. Comparisons of test data for the honeycomb seals with labyrinth and smooth annular seals shows the honeycomb seal had the best sealing (minimum leakage) performance, followed in order by the labyrinth and smooth seals. For prerotated fluids entering the seal, in the direction of shaft rotation, the honeycomb seal has the best rotordynamic stability followed in order by the labyrinth and smooth. For no prerotation, or fluid prerotation against shaft rotation, the labyrinth seal has the best rotordynamic stability followed in order by the smooth and honeycomb seals.

scholarly journals Validation of the generalized model of two-phase thermosyphon loop based on experimental measurements of volumetric flow rate

2016 ◽  
Vol 37 (3) ◽  
pp. 109-138 ◽  
Author(s):  
Henryk Bieliński
Keyword(s):  
Steady State ◽  
Flow Rate ◽  
Vertical Section ◽  
Volumetric Flow Rate ◽  
Working Fluid ◽  
Two Phase ◽  
Generalized Model ◽  
Flow Models ◽  
Theoretical Predictions ◽  
The One

AbstractThe current paper presents the experimental validation of the generalized model of the two-phase thermosyphon loop. The generalized model is based on mass, momentum, and energy balances in the evaporators, rising tube, condensers and the falling tube. The theoretical analysis and the experimental data have been obtained for a new designed variant. The variant refers to a thermosyphon loop with both minichannels and conventional tubes. The thermosyphon loop consists of an evaporator on the lower vertical section and a condenser on the upper vertical section. The one-dimensional homogeneous and separated two-phase flow models were used in calculations. The latest minichannel heat transfer correlations available in literature were applied. A numerical analysis of the volumetric flow rate in the steady-state has been done. The experiment was conducted on a specially designed test apparatus. Ultrapure water was used as a working fluid. The results show that the theoretical predictions are in good agreement with the measured volumetric flow rate at steady-state.

scholarly journals Rotordynamic Coefficient and Leakage Test Results for Interlock and Tooth-on-Stator Labyrinth Seals

1988 ◽  
Author(s):  
Dara W. Childs ◽  
David A. Elrod ◽  
Keith Hale
Keyword(s):  
Labyrinth Seal ◽  
Damping Coefficient ◽  
Test Results ◽  
Labyrinth Seals ◽  
Rotordynamic Coefficients ◽  
Damping Coefficients ◽  
Leakage Test ◽  
Stiffness And Damping ◽  
Rotordynamic Coefficient

Test results (leakage and rotordynamic coefficients) are presented for an interlock and tooth-on-stator labyrinth seals. Tests were carried out with air at speeds out to 16,000 cpm and supply pressures up to 7.5 bars. The rotordynamic coefficients consist of direct and cross-coupled stiffness and damping coefficients. Damping-coefficient data have not previously been presented for interlock seals. The test results support the following conclusions: (a) The interlock seal leaks substantially less than labyrinth seals. (b) Destabilizing forces are lower for the interlock seal. (c) The labyrinth seal has substantially greater direct damping values than the interlock seal. A complete rotordynamics analysis is needed to determine which type of seal would yield the best stability predictions for a given turbomachinery unit.

Verification of a One-Dimensional Two-Phase Flow Model of the Frontal Gap in Electrochemical Machining

1976 ◽  
Vol 98 (2) ◽  
pp. 431-437 ◽  
Author(s):  
F. Fluerenbrock ◽  
R. D. Zerkle ◽  
J. F. Thorpe
Keyword(s):  
Flow Model ◽  
Radial Flow ◽  
Electrochemical Machining ◽  
Equilibrium Conditions ◽  
Two Phase ◽  
One Dimensional ◽  
Supply Pressure ◽  
Theoretical Predictions ◽  
The One ◽  
Experimental Pressure

A set of six equations, which are based on the ECM model developed by Thorpe and Zerkle, can be solved numerically to yield the one-dimensional distributions of pressure, temperature, gas density, gap thickness, void fraction, and electrolyte velocity in the rectilinear ECM frontal gap under equilibrium conditions. The validity of the model, which also applies to radial flow geometries, is confirmed by comparing experimental pressure and gap profiles with theoretical predictions. It is shown that for a given set of operating parameters there is a minimum supply pressure below which no machining is possible. When machining steel with an aqueous NaCl electrolyte the deposition of a black smut (Fe(OH)2) occurs beyond a certain smut-free entrance length, which was experimentally found to be proportional to the inlet gap thickness.

Sign in / Sign up

Export Citation Format

Share Document