Investigating the Effects of Fibrous Material Compression on the Acoustical Behavior of Absorption and Barrier Materials

2006 ◽  
Vol 129 (2) ◽  
pp. 133-140 ◽  
Author(s):  
A. R. Ohadi ◽  
M. Moghaddami
Keyword(s):  
Absorption Coefficient ◽  
Fibrous Material ◽  
Transmission Loss ◽  
Element Model ◽  
Physical Parameters ◽  
Fibrous Materials ◽  
Barrier Materials ◽  
Rigid Frame ◽  
Absorbing Materials ◽  
The Galerkin Method

This paper discusses the effects of compression on acoustical performance of fibrous materials. A finite element model is used to predict the absorption coefficient and transmission loss of absorbing and barrier materials. This model is developed based on the Galerkin method and includes the equation of wave propagation in rigid frame porous material. The compression of fibrous material is entered to the model with relations that explain modifications of physical properties used in the wave equation. Acoustical behavior of absorption and barrier materials with and without compression is studied. It is shown that compression of the material leads to reduction of the transmission loss of the barrier materials and absorption coefficient of absorbing materials. In this regard, “thickness reduction” and “variations of physical parameters” due to compression are investigated.

Investigating the Effects of Porous Material Compression on the Acoustical Behavior of Absorption and Barrier Materials

2005 ◽  
Author(s):  
A. R. Ohadi ◽  
M. Moghaddami
Keyword(s):  
Wave Equation ◽  
Porous Material ◽  
Absorption Coefficient ◽  
Transmission Loss ◽  
Element Model ◽  
Barrier Materials ◽  
Rigid Frame ◽  
Absorbing Materials ◽  
The Galerkin Method ◽  
Coefficient Reduction

The paper discusses the effects of compression on acoustical performance of porous materials. A finite element model is used to predict the absorption coefficient and transmission loss of absorbing and barrier materials. This model is developed based on the Galerkin method and includes the equation of wave propagation in rigid frame porous material. The compression of porous material is entered to the model with relations that explain modifications of physical properties used in wave equation. Acoustical behavior of absorption and barrier materials with and without compression is studied. It is shown in this paper that compression of the material leads to improvement of the transmission loss of the barrier materials, whereas absorption coefficient reduction has been obtained for absorbing materials.

Research of Possibilities of Using the Recycled Materials Based on Rubber and Textiles Combined with Vermiculite Material in the Area of ​​Noise Reduction

2014 ◽  
Vol 1001 ◽  
pp. 171-176 ◽  
Author(s):  
Pavol Liptai ◽  
Marek Moravec ◽  
Miroslav Badida
Keyword(s):  
Absorption Coefficient ◽  
Standing Wave ◽  
Sound Pressure Level ◽  
Sound Absorption ◽  
Sound Pressure ◽  
Sound Level ◽  
Pressure Level ◽  
Sound Absorption Coefficient ◽  
Physical Parameters ◽  
Materials Research

This paper describes possibilities in the use of recycled rubber granules and textile materials combined with vermiculite panel. The aim of the research is the application of materials that will be absorbing or reflecting sound energy. This objective is based on fundamental physical principles of materials research and acoustics. Method of measurement of sound absorption coefficient is based on the principle of standing wave in the impedance tube. With a sound level meter is measured maximum and minimum sound pressure level of standing wave. From the maximum and minimum sound pressure level of standing wave is calculated sound absorption coefficient αn, which can take values from 0 to 1. Determination of the sound absorption coefficient has been set in 1/3 octave band and in the frequency range from 50 Hz to 2000 Hz. In conclusion are proposed possibilities of application of these materials in terms of their mechanical and physical parameters.

Updating Finite Element Model of Combined Structures on the Basis of Dynamic Test Results

1996 ◽  
Author(s):  
Chen Xin ◽  
Qin Ye ◽  
Yuan Xiguang ◽  
Zhang Ping ◽  
Sun Jian
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Test Data ◽  
Dynamic Test ◽  
Element Model ◽  
Physical Parameters ◽  
Structural Joint ◽  
Combined Structure ◽  
Joint Parameters ◽  
Two Stages

Abstract According to the real situation, a new method of updating the finite element model (FEM) of a combined structure step by step is proposed in this paper. It is assumed that there are two types of error when establishing the FEMs. One of them results from the simplifications, in fact, it is severe for complicated structures, which usually assume many simplifications; the other is from the process of identifying structural joint parameters. For this reason, it is recommended that the FEM should be established in two stages. At the first stage, the local physical parameters relating with the simplifications are corrected by using the dynamic test data of the corresponding substructures. Then, the structural joint parameters that link the substructures are corrected by the dynamic test data of the combined structure as a whole. The updating formula is presented and proved, and its algorithm is also described. And the experimental results show that the efficiency and accuracy of the proposed method are quite satisfactory.

scholarly journals Tailoring Plate Thickness of a Helmholtz Resonator for Improved Sound Attenuation

2016 ◽  
Author(s):  
Mohammad Kurdi ◽  
Shahin Nudehi ◽  
Gregory Scott Duncan
Keyword(s):  
Transmission Loss ◽  
Plate Thickness ◽  
Helmholtz Resonator ◽  
Element Model ◽  
Flexible Plate ◽  
End Plate ◽  
Receptance Coupling ◽  
Coupling Techniques ◽  
Gradient Based ◽  
Optimization Search

A Helmholtz resonator with flexible plate attenuates noise in exhaust ducts, and the transmission loss function quantifies the amount of filtered noise at a desired frequency. In this work the transmission loss is maximized (optimized) by allowing the resonator end plate thickness to vary for two cases: 1) a non-optimized baseline resonator, and 2) a resonator with a uniform flexible endplate that was previously optimized for transmission loss and resonator size. To accomplish this, receptance coupling techniques were used to couple a finite element model of a varying thickness resonator end plate to a mass-spring-damper model of the vibrating air mass in the resonator. Sequential quadratic programming was employed to complete a gradient based optimization search. By allowing the end plate thickness to vary, the transmission loss of the non-optimized baseline resonator was improved significantly, 28 percent. However, the transmission loss of the previously optimized resonator for transmission loss and resonator size showed minimal improvement.

Analysis of Effective Pre-Stress of Continuous Rigid Frame Bridge in Service Based on Inversion Theory

2013 ◽  
Vol 671-674 ◽  
pp. 1012-1015
Author(s):  
Zhao Ning Zhang ◽  
Ke Xing Li
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Inversion Method ◽  
Vertical Deflection ◽  
Continuous Rigid Frame Bridge ◽  
Rigid Frame ◽  
Inversion Theory ◽  
Rigid Frame Bridge ◽  
The Finite Element Model

Due to the environment, climate, loads and other factors, the pre-stress applied to the beam is not a constant. It is important for engineers to track the state of the pre-stress in order to ensure security of the bridge in service. To solve the problem mentioned above, the paper puts forward a new way to analyze the effective pre-stress using the displacement inversion method based on the inversion theory according to the measured vertical deflection of the bridge in service at different time. The method is a feasible way to predict the effective pre-stress of the bridge in service. Lastly, taking the pre-stressed concrete continuous rigid frame bridge for example, the effective pre-stress is analyzed by establishing the finite element model.

scholarly journals Non-Wovens as Sound Reducers

2018 ◽  
Vol 55 (2) ◽  
pp. 64-76
Author(s):  
D. Belakova ◽  
A. Seile ◽  
S. Kukle ◽  
T. Plamus
Keyword(s):  
Absorption Coefficient ◽  
Surface Density ◽  
Sound Absorption ◽  
Transmission Loss ◽  
Sound Transmission ◽  
Sound Insulation ◽  
Material Structure ◽  
Sound Transmission Loss ◽  
Sound Waves ◽  
Frequency Range

Abstract Within the present study, the effect of hemp (40 wt%) and polyactide (60 wt%), non-woven surface density, thickness and number of fibre web layers on the sound absorption coefficient and the sound transmission loss in the frequency range from 50 to 5000 Hz is analysed. The sound insulation properties of the experimental samples have been determined, compared to the ones in practical use, and the possible use of material has been defined. Non-woven materials are ideally suited for use in acoustic insulation products because the arrangement of fibres produces a porous material structure, which leads to a greater interaction between sound waves and fibre structure. Of all the tested samples (A, B and D), the non-woven variant B exceeded the surface density of sample A by 1.22 times and 1.15 times that of sample D. By placing non-wovens one above the other in 2 layers, it is possible to increase the absorption coefficient of the material, which depending on the frequency corresponds to C, D, and E sound absorption classes. Sample A demonstrates the best sound absorption of all the three samples in the frequency range from 250 to 2000 Hz. In the test frequency range from 50 to 5000 Hz, the sound transmission loss varies from 0.76 (Sample D at 63 Hz) to 3.90 (Sample B at 5000 Hz).

scholarly journals Kajian Eksperimental Koefisien Redaman Akustik Bahan Pelapis Plat Dek Kapal

2018 ◽  
Vol 3 (1) ◽  
pp. 41
Author(s):  
Wibowo Harso Nugroho ◽  
Nanang J.H. Purnomo ◽  
Hardi Zen ◽  
Andi Rahmadiansah
Keyword(s):  
Absorption Coefficient ◽  
High Frequency ◽  
Transmission Loss ◽  
Base Material ◽  
Sound Insulation ◽  
Insulation Material ◽  
Base Materials ◽  
Specimen Material ◽  
Ship Classification ◽  
Technical Assessment

With the increasingly strict requirements of the ship classification bureau for permissible noise limits to allow passengers and crew to be more comfortable and secure a technical assessment is required to address the characteristics of the noise. A noise beyond the standard allowed in the vessel can be a problem to the ship operators. This noise problem will greatly affects the crews' comfort and passengers. One method to reduce the noise on a ship is to use sound insulation. This paper describes the method for determining the absorption coefficient α and the transmission loss (TL) through an acoustic test of a concrete insulation in the laboratory. The test was conducted by using the method of impedance tube where a speciment response measured by a microphone. In general, the properties of this insulation material remains as the main base material which is concrete. it has been found that the transmission loss value (TL) is in the range of 10 - 50 dB whereas for the base material the concrete is around 22 - 49 dB but the absorption coefficient α of the specimen material is much higher than the material of the base material especially in high frequency, which ranges from 0.15 to 0.97, whereas for concrete base materials have absorbent coefficient α ranges from 0.01 to 0.02.

scholarly journals The 3D structure of fibrous material is fully restorable from its X-ray diffraction pattern

IUCrJ ◽  
2021 ◽  
Vol 8 (4) ◽  
Author(s):  
Hiroyuki Iwamoto
Keyword(s):  
Diffraction Pattern ◽  
Fibrous Material ◽  
3D Structure ◽  
Wide Field ◽  
Fibrous Materials ◽  
X Ray Diffraction ◽  
X Ray ◽  
Fiber Diffraction ◽  
Puzzle Solving ◽  
Diffraction Patterns

X-ray fiber diffraction is potentially a powerful technique to study the structure of fibrous materials, such as DNA and synthetic polymers. However, only rotationally averaged diffraction patterns can be recorded and it is difficult to correctly interpret them without the knowledge of esoteric diffraction theories. Here we demonstrate that, in principle, the non-rotationally averaged 3D structure of a fibrous material can be restored from its fiber diffraction pattern. The method is a simple puzzle-solving process and in ideal cases it does not require any prior knowledge about the structure, such as helical symmetry. We believe that the proposed method has a potential to transform the fiber diffraction to a 3D imaging technique, and will be useful for a wide field of life and materials sciences.

Sign in / Sign up

Export Citation Format

Share Document