Analysis and Design of Buried Pipelines for Ice Gouging Hazard: A Probabilistic Approach

2006 ◽  
Vol 129 (3) ◽  
pp. 219-228 ◽  
Author(s):  
Arash Nobahar ◽  
Shawn Kenny ◽  
Tony King ◽  
Richard McKenna ◽  
Ryan Phillips
Keyword(s):  
Probabilistic Approach ◽  
Three Dimensional ◽  
Local Buckling ◽  
Burial Depth ◽  
The Finite Element Method ◽  
Buried Pipelines ◽  
Analysis And Design ◽  
Cold Environments ◽  
Beam Elements ◽  
Environmental Actions

In cold environments, marine pipelines may be at risk from ice keels that gouge the seabed. Large quantities of material are displaced and soil deformations beneath a gouge may be substantial. To meet safety criteria, excessive strains are avoided by burying pipelines to a sufficient depth. In this paper, a probabilistic approach for the analysis and design of buried pipelines is outlined. Environmental actions are applied through distributions of gouge width, gouge depth, subgouge soil deformations, and bearing pressure. Three-dimensional pipe/soil interaction problem is modeled using nonlinear soil springs and special beam elements using the finite element method to estimate pipe response for statistically possible ranges of gouge depths, gouge widths, and burial depths. Relevant failure mechanisms have been considered, including local buckling and a variety of strain and stress based criteria. The methodology presented in the paper was developed and successfully used for several pipeline and electrical cable projects in ice gouge environments. Significantly reduced burial depth requirements have been demonstrated through the application of the probabilistic approach and through the use of strain-based design criteria. Because ice actions are applied through displacements of the soil, more ductile pipes are often necessary to meet reliability targets.

Engineering Analysis of Shoulder Dystocia in the Human Birth Process by the Finite Element Method

1992 ◽  
Vol 206 (4) ◽  
pp. 243-250 ◽  
Author(s):  
A Meghdari ◽  
R Davoodi ◽  
F Mesbah
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Shoulder Dystocia ◽  
Point Of View ◽  
Engineering Analysis ◽  
The Finite Element Method ◽  
Birth Process ◽  
Beam Elements ◽  
Finite Element Package ◽  
Human Birth

This paper presents an engineering analysis of shoulder dystocia (SD) in the human birth process which usually results in damaging the brachial plexus nerves and the humerus and/or clavicle bones of the baby. The goal is to study these injuries from the mechanical engineering point of view. Two separate finite element models of the neonatal neck and the clavicle bone have been simulated using eight-node three-dimensional elements and beam elements respectively. Simulated models have been analysed under suitable boundary conditions using the ‘SAP80’ finite element package. Finally, results obtained have been verified by comparing them with published clinical and experimental observations.

scholarly journals Significance of geotechnical loads on local buckling response of buried pipelines with respect to conventional practice

2013 ◽  
Vol 50 (1) ◽  
pp. 68-80 ◽  
Author(s):  
Hiva Mahdavi ◽  
Shawn Kenny ◽  
Ryan Phillips ◽  
Radu Popescu
Keyword(s):  
Load Transfer ◽  
Mechanical Performance ◽  
Three Dimensional ◽  
Local Buckling ◽  
Element Model ◽  
Combined Loading ◽  
Buried Pipelines ◽  
Buried Pipe ◽  
Limit States ◽  
New Criterion

Long-term large deformation geohazards can impose excessive deformation on a buried pipeline. The ground displacement field may initiate pipeline deformation mechanisms that exceed design acceptance criteria with respect to serviceability requirements or ultimate limit states. The conventional engineering approach to define the mechanical performance of pipelines has been based on combined loading events for in-air conditions. This methodology may be conservative, as it ignores the soil effect that imposes geotechnical loads, and also provides restraint, on buried pipelines. The importance of pipeline–soil interaction and load-transfer mechanisms that may affect local buckling of buried pipelines is not well understood. A three-dimensional continuum finite element model, simulating the local buckling response of a buried pipe, using the software package ABAQUS/Standard was developed and calibrated. A comprehensive parametric study was previously conducted to investigate the effect of several parameters on local buckling response of pipelines buried in firm clay. A new strain criterion for local buckling of buried pipelines in firm clay through response surface methodology was developed. In this paper, the new criterion is compared with several existing in-air criteria to study the effect of soil restraint on the local buckling response of buried pipelines. The criterion developed in this study predicts greater characteristic critical strain capacity than in-air based criteria that highlights the influence of soil restraint.

Fracture and Deformation Behaviors of Tee Pipe With Local Wall Thinning Under Monotonic Bending

2004 ◽  
Author(s):  
Koji Takahashi ◽  
Kotoji Ando ◽  
Masakazu Hisatsune ◽  
Kunio Hasegawa
Keyword(s):  
Three Dimensional ◽  
Local Buckling ◽  
Metal Loss ◽  
The Finite Element Method ◽  
Bending Tests ◽  
Four Point Bending ◽  
Wall Thinning ◽  
Fracture Behaviors ◽  
Deformation Behaviors ◽  
Local Wall Thinning

Monotonic four-point bending tests were conducted using tee pipe specimens having local wall thinning. The effects of local wall thinning on the fracture behaviors of tee pipes were investigated. Local wall thinning was machined on the inside of pipes in order to simulate erosion/corrosion metal loss. The configurations of the eroded area were l = 100 mm in eroded axial length, d/t = 0.5 and 0.8 in eroded ratio, and 2θ = 90° in eroded angle. The area undergoing local wall thinning was subjected to either tensile or compressive stress. Fracture behaviors of the tee pipes were compared with those of straight pipes. It was found that fracture type could be classified into ovalization, local buckling, and crack initiation, depending on pipe shape, eroded ratio, and stress at the eroded area. Three-dimensional elasto-plastic analyses were also carried out using the finite element method, which is able to accurately simulate fracture behaviors.

Comparison of Conventional and Pontic Fixed Partial Dentures Over Implants Using the Finite Element Method: Three-Dimensional Analysis of Cortical and Medullary Bone Stress

2020 ◽  
Vol 46 (3) ◽  
pp. 175-181
Author(s):  
Marcelo Bighetti Toniollo ◽  
Mikaelly dos Santos Sá ◽  
Fernanda Pereira Silva ◽  
Giselle Rodrigues Reis ◽  
Ana Paula Macedo ◽  
...  
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Medullary Bone ◽  
Principal Stresses ◽  
Bone Stress ◽  
Bone Damage ◽  
Rehabilitation System ◽  
Minimum Requirements

Rehabilitation with implant prostheses in posterior areas requires the maximum number of possible implants due to the greater masticatory load of the region. However, the necessary minimum requirements are not always present in full. This project analyzed the minimum principal stresses (TMiP, representative of the compressive stress) to the friable structures, specifically the vestibular face of the cortical bone and the vestibular and internal/lingual face of the medullary bone. The experimental groups were as follows: the regular splinted group (GR), with a conventional infrastructure on 3 regular-length Morse taper implants (4 × 11 mm); and the regular pontic group (GP), with a pontic infrastructure on 2 regular-length Morse taper implants (4 × 11 mm). The results showed that the TMiP of the cortical and medullary bones were greater for the GP in regions surrounding the implants (especially in the cervical and apical areas of the same region) but they did not reach bone damage levels, at least under the loads applied in this study. It was concluded that greater stress observed in the GP demonstrates greater fragility with this modality of rehabilitation; this should draw the professional's attention to possible biomechanical implications. Whenever possible, professionals should give preference to use of a greater number of implants in the rehabilitation system, with a focus on preserving the supporting tissue with the generation of less intense stresses.

Towards Predicting Relative Belt Edge Endurance With the Finite Element Method

1990 ◽  
Vol 18 (4) ◽  
pp. 216-235 ◽  
Author(s):  
J. De Eskinazi ◽  
K. Ishihara ◽  
H. Volk ◽  
T. C. Warholic
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Shear Deformations ◽  
Element Analysis ◽  
Vertical Loading ◽  
Predicted Values ◽  
Element Method

Abstract The paper describes the intention of the authors to determine whether it is possible to predict relative belt edge endurance for radial passenger car tires using the finite element method. Three groups of tires with different belt edge configurations were tested on a fleet test in an attempt to validate predictions from the finite element results. A two-dimensional, axisymmetric finite element analysis was first used to determine if the results from such an analysis, with emphasis on the shear deformations between the belts, could be used to predict a relative ranking for belt edge endurance. It is shown that such an analysis can lead to erroneous conclusions. A three-dimensional analysis in which tires are modeled under free rotation and static vertical loading was performed next. This approach resulted in an improvement in the quality of the correlations. The differences in the predicted values of various stress analysis parameters for the three belt edge configurations are studied and their implication on predicting belt edge endurance is discussed.

scholarly journals Compressive behaviours of octet-truss lattices

2020 ◽  
Vol 234 (16) ◽  
pp. 3257-3269 ◽  
Author(s):  
Yifan Li ◽  
Huaiyuan Gu ◽  
Martyn Pavier ◽  
Harry Coules
Keyword(s):  
Failure Modes ◽  
Density Ratio ◽  
Three Dimensional ◽  
Compressive Load ◽  
High Strength ◽  
Detailed Comparison ◽  
Compressive Response ◽  
Beam Elements ◽  
Structural Applications ◽  
Octet Truss

Octet-truss lattice structures can be used for lightweight structural applications due to their high strength-to-density ratio. In this research, octet-truss lattice specimens were fabricated by stereolithography additive manufacturing with a photopolymer resin. The mechanical properties of this structure have been examined in three orthogonal orientations under the compressive load. Detailed comparison and description were carried out on deformation mechanisms and failure modes in different lattice orientations. Finite element models using both beam elements and three-dimensional solid elements were used to simulate the compressive response of this structure. Both the load reaction and collapse modes obtained in simulations were compared with test results. Our results indicate that three-dimensional continuum element models are required to accurately capture the behaviour of real trusses, taking into account the effects of finite-sized beams and joints.

scholarly journals The effect of the outlet angle β2 on the thermomechanical behavior of a centrifugal compressor blade

2020 ◽  
Vol 29 (1) ◽  
pp. 1-8
Author(s):  
Ahmed Allali ◽  
Sadia Belbachir ◽  
Ahmed Alami ◽  
Belhadj Boucham ◽  
Abdelkader Lousdad
Keyword(s):  
Mechanical Behavior ◽  
Centrifugal Compressor ◽  
Three Dimensional ◽  
Complex Form ◽  
Compressor Blade ◽  
Stress Fields ◽  
The Finite Element Method ◽  
Mechanical Fatigue ◽  
Outlet Angle ◽  
The Impact

AbstractThe objective of this work lies in the three-dimensional study of the thermo mechanical behavior of a blade of a centrifugal compressor. Numerical modeling is performed on the computational code "ABAQUS" based on the finite element method. The aim is to study the impact of the change of types of blades, which are defined as a function of wheel output angle β2, on the stress fields and displacements coupled with the variation of the temperature.This coupling defines in a realistic way the thermo mechanical behavior of the blade where one can note the important concentrations of stresses and displacements in the different zones of its complex form as well as the effects at the edges. It will then be possible to prevent damage and cracks in the blades of the centrifugal compressor leading to its failure which can be caused by the thermal or mechanical fatigue of the material with which the wheel is manufactured.

The Analysis and Design of a Fire Engine Safety Cab Using Finite Element Methods

1977 ◽  
Vol 191 (1) ◽  
pp. 187-193 ◽  
Author(s):  
J. C. Miles ◽  
G. A. Wardill
Keyword(s):  
Finite Element ◽  
Computer Program ◽  
Three Dimensional ◽  
Analysis And Design ◽  
Vehicle Structure ◽  
Collapse Analysis ◽  
Incremental Formulation ◽  
Analysis Computer ◽  
Fire Engine ◽  
Analysis Computer Program

A three dimensional structural collapse analysis computer program is described, and illustrated by reference to a safety vehicle structure analysed and designed using the program. The particular problems of large displacements and material non-linearity are accounted for, and a method of estimating the permanent set which results after impact is described. Based on an incremental formulation of the conventional finite-element method, the computer program is capable of tracing the complete load deflection characteristics of a structure up to and beyond the point of collapse.

Research on the Reliability of Box for Gear Test Bed

2011 ◽  
Vol 121-126 ◽  
pp. 1744-1748
Author(s):  
Xiang Yang Jin ◽  
Tie Feng Zhang ◽  
Li Li Zhao ◽  
He Teng Wang ◽  
Xiang Yi Guan
Keyword(s):  
Power Flow ◽  
Dynamic Performance ◽  
Three Dimensional ◽  
Design Parameters ◽  
The Finite Element Method ◽  
Test Bed ◽  
Kinematics Simulation ◽  
Beveloid Gears ◽  
Overall Performance

To determine the efficiency, load-bearing capacity and fatigue life of beveloid gears with intersecting axes, we design a mechanical gear test bed with closed power flow. To test the quality of its structure and predict its overall performance, we establish a three-dimensional solid model for various components based on the design parameters and adopt the technology of virtual prototyping simulation to conduct kinematics simulation on it. Then observe and verify the interactive kinematic situation of each component. Moreover, the finite element method is also utilized to carry out structural mechanics and dynamics analysis on some key components. The results indicate that the test bed can achieve the desired functionality, and the static and dynamic performance of some key components can also satisfy us.

Sign in / Sign up

Export Citation Format

Share Document