Heat Transfer Behavior for a Stationary or Rotating MCM Disk With an Unconfined Round Jet Impingement

2006 ◽  
Vol 129 (4) ◽  
pp. 400-410 ◽  
Author(s):  
C. J. Fang ◽  
M. C. Wu ◽  
Y. M. Kuo ◽  
C. Y. Lee ◽  
C. H. Peng ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Steady State ◽  
Mixed Convection ◽  
Jet Impingement ◽  
Disk Surface ◽  
Average Heat ◽  
Nusselt Numbers ◽  
Transient Period ◽  
Transfer Behavior

A series of experimental investigations on the studies related to fluid flow and transient mixed convection from a horizontally unconfined stationary or rotating ceramic-based multichip module (MCM) disk with unconfined jet impingement have been successfully conducted. The fluid flow and heat transfer behavior explored includes the streamwise velocity and turbulence intensity distributions, transient dimensionless temperature distribution on the MCM disk surface, transient heat flux distribution of input power, and transient chip and average heat transfer characteristics on the MCM disk surface. Besides, two new correlations of transient stagnation and average Nusselt numbers in terms of jet Reynolds number, ratio of jet separation distance to nozzle diameter and time elapsed during the transient period, are presented for the cases of stationary MCM disk. For the cases of rotating MCM disk, a complete composite correlation of steady-state average Nusselt number for mixed convection due to jet impingement, disk rotation and buoyancy is proposed. As compared with the steady-state results, if the transient chip and average heat transfer behaviors may be considered as a superposition of a series of quasisteady states, the transient chip and average Nusselt numbers in all the present transient experiments can be properly predicted by the existing steady-state correlations when t>6min in the power-on transient period.

Convective Heat Transfer From a Stationary or Rotating MCM Disk With a Unconfined Round Jet Impingement

2005 ◽  
Author(s):  
Y. M. Kuo ◽  
C. J. Fang ◽  
M. C. Wu ◽  
C. H. Peng ◽  
Y. H. Hung
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Steady State ◽  
Mixed Convection ◽  
Jet Impingement ◽  
Disk Surface ◽  
Separation Distance ◽  
Heat Flux Distribution ◽  
Disk Rotation ◽  
Nusselt Numbers

A series of experimental investigations with stringent measurement methods on the studies related to fluid flow and transient mixed convection from a horizontally unconfined stationary or rotating ceramic-based MCM disk with unconfined jet impingement have been successfully conducted. The relevant parameters influencing fluid flow and heat transfer performance are (1) mixed convection due to jet impingement and buoyancy: steady-state Grashof number, jet Reynolds number, and ratio of jet separation distance to nozzle diameter; and (2) mixed convection due to jet impingement, disk rotation and buoyancy: steady-state Grashof number, jet Reynolds number (Rej), rotational Reynolds number (Rer), ratio of jet separation distance to nozzle diameter (H/d). The thermal behavior explored includes the transient temperature distribution on the MCM disk surface, transient heat flux distribution of input power, transient convective heat flux distribution of chips, and transient chip and average heat transfer characteristics on the MCM disk surface. Besides, two new correlations of transient stagnation and average Nusselt numbers in terms of Rej, H/d and t are presented for the cases of stationary MCM disk. For the cases of rotating MCM disk, a new empirical correlation to classify two regimes of heat transfer modes such as disk rotation mode and jet impingement mode is presented; and a complete composite correlation of steady-state average Nusselt number for mixed convection due to jet impingement, disk rotation and buoyancy is proposed. As compared with the steady-state results, if the transient chip and average heat transfer behaviors may be considered as a superposition of a series of quasi-steady states, the transient chip and average Nusselt numbers in all the present transient experiments can be properly predicted by the existing steady-state correlations when t > 6 min in the power-on transient period.

Transient Convective Heat Transfer of Air Jet Impinging Onto a Confined Ceramic-Based MCM Disk

2001 ◽  
Author(s):  
W. S. Su ◽  
L. K. Liu ◽  
Y. H. Hung
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Jet Impingement ◽  
Disk Surface ◽  
Separation Distance ◽  
Transient Time ◽  
Nusselt Numbers ◽  
Air Jet ◽  
Transient Experiments ◽  
Transfer Behavior

Abstract Transient heat transfer behavior from a horizontally confined ceramic-based MCM disk with jet impingement has been systematically explored. The relevant parameters influencing heat transfer performance are the steady-state Grashof number, jet Reynolds number, and ratio of jet separation distance to nozzle diameter. In addition, an effective time, ton, representing a certain transient time when the mixed convection effect due to jet impingement and buoyancy becomes significant relative to heat conduction, is introduced. Both the transient chip and average Nusselt numbers on the MCM disk surface decrease with time in a very beginning period of 0 ≤ t < ton, whereas it gradually increases or keeps constant with time and finally approaches the steady-state value in the period of ton ≤ t < ts. As compared with the steady-state results, if the transient chip and average heat transfer behaviors may be considered as a superposition of a series of quasi-steady states, the transient chip and average Nusselt numbers in all the present transient experiments can be properly predicted by the existing steady-state correlations when t ≥ 4 min in the power-on transient period.

Transient Convective Heat Transfer of Air Jet Impinging Onto a Confined Ceramic-Based MCM Disk

2004 ◽  
Vol 126 (1) ◽  
pp. 159-172 ◽  
Author(s):  
Li-Kang Liu ◽  
Wen-Shien Su ◽  
Ying-Huei Hung
Keyword(s):  
Heat Transfer ◽  
Steady State ◽  
Jet Impingement ◽  
Disk Surface ◽  
Separation Distance ◽  
Transient Time ◽  
Nusselt Numbers ◽  
Air Jet ◽  
Transient Experiments ◽  
Transfer Behavior

Transient heat transfer behavior from a horizontally confined ceramic-based MCM disk with jet impingement has been systematically explored. The relevant parameters influencing heat transfer performance are the steady-state Grashof number, jet Reynolds number, and ratio of jet separation distance to nozzle diameter. In addition, an effective time, ton, representing a certain transient time when the mixed convection effect due to jet impingement and buoyancy becomes significant relative to heat conduction, is introduced. Both the transient chip and average Nusselt numbers on the MCM disk surface decrease with time in a very beginning period of 0⩽t<ton, whereas it gradually increases or keeps constant with time and finally approaches the steady-state value in the period of ton⩽t<ts. As compared with the steady-state results, if the transient chip and average heat transfer behaviors may be considered as a superposition of a series of quasi-steady states, the transient chip and average Nusselt numbers in all the present transient experiments can be properly predicted by the existing steady-state correlations when t⩾4min in the power-on transient period.

Convective Heat Transfer From Heated Extended Surfaces With a Confined Slot Jet Impingement

2004 ◽  
Author(s):  
L. K. Liu ◽  
M. C. Wu ◽  
C. J. Fang ◽  
Y. H. Hung
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Reynolds Number ◽  
Mixed Convection ◽  
Average Nusselt Number ◽  
Jet Impingement ◽  
Separation Distance ◽  
Nusselt Numbers ◽  
Transfer Behavior ◽  
Extended Surfaces

A series of experimental investigations with stringent measurement methods on the studies related to mixed convection from the horizontally confined extended surfaces with a slot jet impingement have been successfully conducted. The relevant parameters influencing mixed convection performance due to jet impingement and buoyancy include the Grashof number, ratio of jet separation distance to nozzle width, ratio of extended surfaces height to nozzle width and jet Reynolds number. The range of these parameters studied are Grs = 3.77 × 105 – 1.84 × 106, H/W = 1–10, Hs/W = 0.74–3.40 and Re = 63–1383. In the study, the heat transfer behavior on the extended surfaces with confined slot jet impingement such as the temperature distribution, local and average Nusselt numbers on the extended surfaces has been systematically explored. The results manifest that the effect of steady-state Grashof number on heat transfer behavior such as stagnation, local and average Nusselt number is not significant; while the heat transfer performance increases with decreasing jet separation distance or with increasing extended surface height and jet Reynolds number. Besides, two new correlations of local and average Nusselt numbers in terms of H/W, Hs/W and Re are proposed for the cases of extended surfaces. A satisfactory agreement is achieved between the results predicted by these correlations and the experimental data. Finally, a complete composite correlation of steady-state average Nusselt number for mixed convection due to jet impingement and buoyancy is proposed. The comparison of the predictions evaluated by this correlation with all the present experimental data is made. The maximum and average deviations of the predictions from the experimental data are 7.46% and 2.87%, respectively.

scholarly journals RANS Simulation of the Effect of Pulse Form on Fluid Flow and Convective Heat Transfer in an Intermittent Round Jet Impingement

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 4025
Author(s):  
M. A. Pakhomov ◽  
V. I. Terekhov
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Fluid Flow ◽  
Steady State ◽  
Jet Impingement ◽  
Pulse Frequency ◽  
Steady State Flow ◽  
Pulsed Jet ◽  
Flow And Heat Transfer ◽  
Pulse Form

The of effect pulse form (rectangular, sinusoidal and triangular) on the fluid flow and heat transfer of an intermittent jet impingement was studied numerically. It was shown in a non-steady-state jet, both an increase and decrease in heat transfer are possible compared with steady-state jet for all investigated pulse forms. For small distances between the pipe edge and obstacle (H/D ≤ 6) in the pulsed jet, heat transfer around the stagnation point increases with increasing pulse frequency, while for H/D > 8 an increase in frequency causes a heat transfer decrease. A growth in the Reynolds number causes a decrease in heat transfer, and data for all frequencies approach the steady-state flow regime. The numerical model is compared with the experimental results. Satisfactory agreement on the influence of the form and frequency of pulses on heat transfer for the pulsed jet on the obstacle surface is obtained.

Convective Heat Transfer From Confined Heated Surfaces With Slot Jet Impingement

2005 ◽  
Author(s):  
L. K. Liu ◽  
C. J. Fang ◽  
M. C. Wu ◽  
C. H. Peng ◽  
Y. H. Hung
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Steady State ◽  
Convective Heat ◽  
Local Nusselt Number ◽  
Jet Impingement ◽  
Experimental Investigations ◽  
Surface Center ◽  
Nusselt Numbers ◽  
Extended Surface

A series of experimental investigations with a stringent measurement method on the transient-/steady-state heat transfer behavior for confined smooth surfaces with slot jet impingement have been successfully conducted. From the results, a generalized correlation is proposed to represent the distributions of normalized transient convective heat flux. The highest heat transfer during the transient period occurs at the surface center of confined heated smooth or extended surface. The transient local Nusselt number decreases along the distance from the surface center toward the surface edge. The transient-/steady-state local and average Nusselt numbers are almost independent of Grs, and they are more significantly affected by ReD as compared with H/W. They will increase with increasing ReD. Maximum local and average Nusselt numbers can be found between H/W = 3 and H/W = 5. The effects of Grs and H/W on the dimensionless local Nusselt number distribution are insignificant; and the distribution can be expressed as a generalized bell-shaped profile, which is only dependent of ReD. Finally, a new composite correlation of steady-state average Nusselt number for mixed convection from confined smooth due to slot jet impingement and buoyancy are presented.

On heat transfer and flow characteristics of jets impinging onto concave surface with varying bleeding arrangements

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Dandan Qiu ◽  
Lei Luo ◽  
Zhiqi Zhao ◽  
Songtao Wang ◽  
Zhongqi Wang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Thermal Performance ◽  
Film Cooling ◽  
Flow Characteristics ◽  
Jet Impingement ◽  
Heat Transfer Characteristics ◽  
Content Type ◽  
Transfer Characteristics ◽  
Nusselt Numbers

Purpose The purpose of this study is to investigate the effects of film holes’ arrangements and jet Reynolds number on flow structure and heat transfer characteristics of jet impingement conjugated with film cooling in a semicylinder double wall channel. Design/methodology/approach Numerical simulations are used in this research. Streamlines on different sections, skin-friction lines, velocity, wall shear stress and turbulent kinetic energy contours near the concave target wall and vortices in the double channel are presented. Local Nusselt number contours and surface averaged Nusselt numbers are also obtained. Topology analysis is applied to further understand the fluid flow and is used in analyzing the heat transfer characteristics. Findings It is found that the arrangement of side films positioned far from the center jets helps to enhance the flow disturbance and heat transfer behind the film holes. The heat transfer uniformity for the case of 55° films arrangement angle is most improved and the thermal performance is the highest in this study. Originality/value The film holes’ arrangements effects on fluid flow and heat transfer in an impingement cooled concave channel are conducted. The flow structures in the channel and flow characteristics near target by topology pictures are first obtained for the confined film cooled impingement cases. The heat transfer distributions are analyzed with the flow characteristics. The highest heat transfer uniformity and thermal performance situation is obtained in present work.

Forced Convective Heat Transfer for Partially-Confined Compact PPF Heat Sinks With Top-Bypass Effect

2005 ◽  
Author(s):  
T. Y. Wu ◽  
M. P. Wang ◽  
J. T. Horng ◽  
S. F. Chang ◽  
Y. H. Hung
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Steady State ◽  
Convective Heat ◽  
Average Nusselt Number ◽  
Heat Dissipation ◽  
Heat Sinks ◽  
Nusselt Numbers ◽  
Transient Period ◽  
State Average

A series of experimental investigations with a stringent measurement method on the study of the fluid flow and heat transfer for confined compact heat sinks in forced convection have been successfully conducted. From the results, the thermal capacity of the heat sink and the convective heat dissipation play the major roles for dominating the transient thermal behavior in the beginning of power-on transient period; while, the convective heat dissipation finally becomes the solely dominating term at the end of power-on transient period. The transient/steady-state local and average Nusselt numbers increase with increasing Grs, H/Hc ratio or Re. As compared with the steady-state average Nusselt number for non-compact heat sink (Fin-Al/ Base-Al), the steady-state heat transfer enhancement for compact heat sinks (Fin-Al/Base-Al) is 185.74%. Furthermore, a new correlation of steady-state average Nusselt number in terms of relevant influencing parameters for confined compact PPF heat sinks in forced convection is proposed. As compared with two existing correlations of steady-state average Nusselt numbers for unconfined and confined non-compact PPF heat sinks, the heat transfer enhancements for the present confined compact PPF heat sinks of H/Hc = 0.47 are 423.29% and 219.93%, respectively.

scholarly journals The Influence of Different Types of Nanofluid on Thermal and Fluid Flow Performance of Liquid Cold Plate

2018 ◽  
Vol 7 (4.35) ◽  
pp. 148 ◽  
Author(s):  
Nur Irmawati Om ◽  
Rozli Zulkifli ◽  
P. Gunnasegaran
Keyword(s):  
Heat Transfer ◽  
Fluid Flow ◽  
Steady State ◽  
Pressure Drop ◽  
Volume Fraction ◽  
Cold Plate ◽  
Governing Equations ◽  
Flow And Heat Transfer ◽  
Different Types ◽  
Volume Method

The influence of utilizing different nanofluids types on the liquid cold plate (LCP) is numerically investigated. The thermal and fluid flow performance of LCP is examined by using pure ethylene glycol (EG), Al2O3-EG and CuO-EG. The volume fraction of the nanoparticle for both nanofluid is 2%. The finite volume method (FVM) has been used to solved 3-D steady state, laminar flow and heat transfer governing equations. The presented results indicate that Al2O3-EG able to provide the lowest surface temperature of the heater block followed by CuO-EG and EG, respectively. It is also found that the pressure drop and friction factor are higher for Al2O3-EG and CuO-EG compared to the pure EG.

Sign in / Sign up

Export Citation Format

Share Document