NOx Emissions From a Diesel Engine Fueled With Natural Gas

1995 ◽  
Vol 117 (4) ◽  
pp. 290-296 ◽  
Author(s):  
Y. Tao ◽  
K. B. Hodgins ◽  
P. G. Hill
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Ignition Delay ◽  
Substantial Reduction ◽  
Equilibrium Concentration ◽  
Nox Emission ◽  
Combustion Model ◽  
Injection Timing ◽  
Exhaust Pipe ◽  
Nox Emissions

The performance and emission characteristics of a single-cylinder two-stroke diesel engine fueled with direct injection of natural gas entrained with pilot diesel ignition enhancer have been measured. The thermal efficiency of the optimum gas-diesel operation was shown to exceed that of the conventional diesel at full load, but to be less at part load where the ignition delay was excessive. At high load, where the NOx emission problem is most serious, substantial reduction in NOx emission rate was obtained with delay of injection timing and also with use of exhaust gas recirculation. Measured cylinder pressures were used with a three-zone combustion model to determine ignition delay and the temperatures of the burned gas. The predicted NOx emissions based on equilibrium concentration of NO at the maximum burned gas temperature were found to correlate closely with exhaust pipe measurements of NOx.

scholarly journals Combustion Analysis of a Diesel Engine during Warm up at Different Coolant and Lubricating Oil Temperatures

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3931
Author(s):  
Faisal Lodi ◽  
Ali Zare ◽  
Priyanka Arora ◽  
Svetlana Stevanovic ◽  
Mohammad Jafari ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Ignition Delay ◽  
Peak Pressure ◽  
Cold Start ◽  
Lubricating Oil ◽  
Combustion Model ◽  
Injection Timing ◽  
Warm Up ◽  
Combustion Duration ◽  
Hot Start

A comprehensive analysis of combustion behaviour during cold, intermediately cold, warm and hot start stages of a diesel engine are presented. Experiments were conducted at 1500 rpm and 2000 rpm, and the discretisation of engine warm up into stages was facilitated by designing a custom drive cycle. Advanced injection timing, observed during the cold start period, led to longer ignition delay, shorter combustion duration, higher peak pressure and a higher peak apparent heat release rate (AHRR). The peak pressure was ~30% and 20% and the AHRR was ~2 to 5% and ±1% higher at 1500 rpm and 2000 rpm, respectively, during cold start, compared to the intermediate cold start. A retarded injection strategy during the intermediate cold start phase led to shorter ignition delay, longer combustion duration, lower peak pressure and lower peak AHRR. At 2000 rpm, an exceptional combustion behaviour led to a ~27% reduction in the AHRR at 25% load. Longer ignition delays and shorter combustion durations at 25% load were observed during the intermediately cold, warm and hot start segments. The mass fraction burned (MFB) was calculated using a single zone combustion model to analyse combustion parameters such as crank angle (CA) at 50% MFB, AHRR@CA50 and CA duration for 10–90% MFB.

Optimization of a Marine Medium-Speed Engine With Multi-Injector System by 1D Predictive Simulation

2021 ◽  
Author(s):  
Dai Liu ◽  
Peng Zhang ◽  
Long Liu ◽  
Qian Xia ◽  
Xiuzhen Ma
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Engine Performance ◽  
Nox Emission ◽  
Combustion Model ◽  
Injection Timing ◽  
Engine Model ◽  
Medium Speed ◽  
Injector System ◽  
Marine Medium

Abstract The thermal efficiency and emission of large bore marine medium-speed diesel engine are required to be improved under the stringent legislations. A multi-injector system has been proposed in order to improve the thermal efficiency and NOx emission instantaneously. However, application of the multi-injector system increased the complexity of parameter optimization and control. To develop proper control strategy of the novel multi-injector system, a 1D engine model of the original engine configurations was developed initially, including a predictive combustion model in commercial 1D simulation program (GT-Power). After calibrated by test results and literature data under various engine loads, the engine model was modified from a central single injector engine to a multi-injector engine. On the basis of a conventional direct-injection diesel engine, another two injectors were added to the cylinder as side injectors in the model. And the fundamental combustion characteristics and engine performance of the marine medium-speed diesel engine with multi-injector are investigated under various injection quantity ratio between the central injector and side injectors. The effects of injection timing and split injection are also studied by simulation. The result indicated that the effective thermal efficiency and NOx emission of the medium speed marine diesel engine are optimized instantaneously by changing the injection strategies of the central and side injectors. Finally, the preferred injection strategy is proposed by the 1D model.

A Study on Reducing the NOx Emission of the L21/31 Medium-Speed Marine Diesel Engine for IMO Tier Emission Legislation

2013 ◽  
Vol 291-294 ◽  
pp. 1920-1924
Author(s):  
Min Xiao ◽  
Hui Chen
Keyword(s):  
Numerical Simulation ◽  
Diesel Engine ◽  
Fuel Injection ◽  
Nox Emission ◽  
Injection Timing ◽  
Marine Diesel Engine ◽  
Nox Emissions ◽  
Variable Parameters ◽  
Medium Speed ◽  
Marine Diesel

The KIVA-3V program was used to make numerical simulation for L21/31 type of medium-speed marine diesel engine about the NOx emissions and the affection of NOx changing process on different variable parameters under the Tier Ⅱstandard. On this basis, a discussion towards the NOx emission of the model fueling with dimethyl ether (DME) to meet the Tier Ⅲ standard is offered. The results show that reducing the intake temperature, load and speed, postponing the fuel injection timing and intake lag angle properly can decrease the NOx emissions within the limits of NOx in TierⅡ standard. Comparing the results of the numerical simulation of DME and diesel fuel, the NOx emission of the former one is 60.85% of the latter one, and the NOx emission of changing variable parameters on DME engine is 35.56% of the original type of diesel engine, very close to the Tier Ⅲ.

scholarly journals Research on the Influence of Euro VI Diesel Engine Assembly Consistency on NOx Emissions

Energies ◽  
2020 ◽  
Vol 13 (20) ◽  
pp. 5335
Author(s):  
Wei Yan ◽  
Tengyao Dou ◽  
Jinbo Wang ◽  
Na Mei ◽  
Guoxiang Li
Keyword(s):  
Experimental Data ◽  
Diesel Engine ◽  
Combustion Chamber ◽  
Nox Emission ◽  
Combustion Model ◽  
Nox Emissions ◽  
Assembly Tolerance ◽  
Nozzle Extension ◽  
Assembly Tolerance Variation ◽  
Chamber Diameter

The assembly consistency of a diesel engine will affect its nitrogen oxides (NOx) emission variation. In order to improve the NOx emissions of diesel engines, a study was carried out based on the assembly tolerance variation of the diesel engine’s combustion system. Firstly, a diesel engine which meets the Euro VI standards together with the experimental data is obtained. The mesh model and combustion model of the engine combustion system are built in the Converge software (version 2.4, Tecplot, Bellevue, DC, USA), and the experimental data is used to calibrate the combustion model obtained in the Converge software. Then, the four-factor and three-level orthogonal simulation experiments are carried out on the dimension parameters that include nozzle extension height, throat diameter, shrinkage diameter and combustion chamber depth. Through mathematical analysis on the experimental data, the results show that the variation of nozzle extension height and combustion chamber depth have a strong influence on NOx emission results, and the variation of combustion chamber diameter also has a weak influence on NOx production. According to the regression model obtained from the analysis, there is a quadratic function relating the nozzle extension height and NOx emissions and the amount of NOx increases with increasing nozzle extension height. The relationship between emission performance and size parameters is complex. In the selected size range, the influence of the variation of the chamber diameter on NOx is linear. The variation of the chamber depth also has an effect on NOx production, and the simulation results vary with the change of assembly tolerance variation. Thus, in the engine assembly process, it is necessary to strictly control the nozzle extension height and combustion chamber depth. The research results are useful to improve the NOx emission of diesel engine and provide a basis for the control strategy of selective catalytic reduction (SCR) devices.

scholarly journals The effects of exhaust gas re-circulation and injection timing on combustion performance and emissions of biodiesel and its blends with 2-methylfuran in a diesel engine

2020 ◽  
Vol 24 (1 Part A) ◽  
pp. 215-229
Author(s):  
Helin Xiao ◽  
Xiaolong Yang ◽  
Ru Wang ◽  
Shengjun Li ◽  
Jie Ruan ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Ignition Delay ◽  
Injection Timing ◽  
Nox Emissions ◽  
Exhaust Gas ◽  
Brake Specific Fuel Consumption ◽  
Combustion Duration ◽  
Circulation Ratio

In this study, the influences of injection timing and exhaust gas re-circulation on combustion and emissions characteristics of biodiesel/2-methylfuran blends are investigated on a modified water-cooled 4-cylinder four-stroke direct injection compression ignition engine. The experimental conditions are, respectively, to adjust injection timing and exhaust gas re-circulation ratio at 0.38 MPa break mean effective pressure with the engine speed at 1800 rpm constantly. With injection timing in advance, the peak cylinder pressure rose while maximum heat re-lease rate first decreased and next slightly raised. Ignition delay and brake specific fuel consumption reduced first and then raised while combustion duration and break thermal efficiency had the opposite trend. The NOx emissions in-creased, and HC emissions first reduced significantly and then slightly increased, while 1,3-butadiene and acetaldehyde emissions presented a reduction tendency. As exhaust gas re-circulation ratio increased gradually, ignition delay as well as combustion duration was prolonged. brake specific fuel consumption increased and break thermal efficiency declined. HC, CO, 1,3-butadiene, and acetaldehyde emissions raised while NOx emissions reduced significantly. Biodiesel could be-have well in a Diesel engine and thus a feasible alternative fuel for diesel. More-over, methylfuran addition into biodiesel could raise break thermal efficiency and the break thermal efficiency of BM20 is higher than BM10. However, both BM10 and BM20 appeared a combustion deterioration when injection timing at 2.5?CA before top head center.

scholarly journals Investigation of Effect on Environmental Performance of Using LNG as Fuel for Engines in Seaport Tugboats

2021 ◽  
Vol 9 (2) ◽  
pp. 123
Author(s):  
Sergejus Lebedevas ◽  
Lukas Norkevičius ◽  
Peilin Zhou
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Baltic Sea ◽  
Impact Assessment ◽  
Fuel Consumption ◽  
Dual Fuel ◽  
Nox Emissions ◽  
The Baltic Sea ◽  
Emission Analysis ◽  
The Baltic

Decarbonization of ship power plants and reduction of harmful emissions has become a priority in the technological development of maritime transport, including ships operating in seaports. Engines fueled by diesel without using secondary emission reduction technologies cannot meet MARPOL 73/78 Tier III regulations. The MEPC.203 (62) EEDI directive of the IMO also stipulates a standard for CO2 emissions. This study presents the results of research on ecological parameters when a CAT 3516C diesel engine is replaced by a dual-fuel (diesel-liquefied natural gas) powered Wartsila 9L20DF engine on an existing seaport tugboat. CO2, SO2 and NOx emission reductions were estimated using data from the actual engine load cycle, the fuel consumption of the KLASCO-3 tugboat, and engine-prototype experimental data. Emission analysis was performed to verify the efficiency of the dual-fuel engine in reducing CO2, SO2 and NOx emissions of seaport tugboats. The study found that replacing a diesel engine with a dual-fuel-powered engine led to a reduction in annual emissions of 10% for CO2, 91% for SO2, and 65% for NOx. Based on today’s fuel price market data an economic impact assessment was conducted based on the estimated annual fuel consumption of the existing KLASCO-3 seaport tugboat when a diesel-powered engine is replaced by a dual-fuel (diesel-natural gas)-powered engine. The study showed that a 33% fuel costs savings can be achieved each year. Based on the approved methodology, an ecological impact assessment was conducted for the entire fleet of tugboats operating in the Baltic Sea ports if the fuel type was changed from diesel to natural gas. The results of the assessment showed that replacing diesel fuel with natural gas achieved 78% environmental impact in terms of NOx emissions according to MARPOL 73/78 Tier III regulations. The research concludes that new-generation engines on the market powered by environmentally friendly fuels such as LNG can modernise a large number of existing seaport tugboats, significantly reducing their emissions in ECA regions such as the Baltic Sea.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

A phenomenological combustion analysis of a dual-fuel natural-gas diesel engine

2016 ◽  
Vol 231 (1) ◽  
pp. 66-83 ◽  
Author(s):  
Shuonan Xu ◽  
David Anderson ◽  
Mark Hoffman ◽  
Robert Prucka ◽  
Zoran Filipi
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Heat Release ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Dual Fuel ◽  
Injection Timing ◽  
Heavy Duty ◽  
Engine System ◽  
Wiebe Function

Energy security concerns and an abundant supply of natural gas in the USA provide the impetus for engine designers to consider alternative gaseous fuels in the existing engines. The dual-fuel natural-gas diesel engine concept is attractive because of the minimal design changes, the ability to preserve a high compression ratio of the baseline diesel, and the lack of range anxiety. However, the increased complexity of a dual-fuel engine poses challenges, including the knock limit at a high load, the combustion instability at a low load, and the transient response of an engine with directly injected diesel fuel and port fuel injection of compressed natural gas upstream of the intake manifold. Predictive simulations of the complete engine system are an invaluable tool for investigations of these conditions and development of dual-fuel control strategies. This paper presents the development of a phenomenological combustion model of a heavy-duty dual-fuel engine, aided by insights from experimental data. Heat release analysis is carried out first, using the cylinder pressure data acquired with both diesel-only and dual-fuel (diesel and natural gas) combustion over a wide operating range. A diesel injection timing correlation based on the injector solenoid valve pulse widths is developed, enabling the diesel fuel start of injection to be detected without extra sensors on the fuel injection cam. The experimental heat release trends are obtained with a hybrid triple-Wiebe function for both diesel-only operation and dual-fuel operation. The ignition delay period of dual-fuel operation is examined and estimated with a predictive correlation using the concept of a pseudo-diesel equivalence ratio. A four-stage combustion mechanism is discussed, and it is shown that a triple-Wiebe function has the ability to represent all stages of dual-fuel combustion. This creates a critical building block for modeling a heavy-duty dual-fuel turbocharged engine system.

An Experimental Study on Smoke Reduction Effect of Post Injection in Combination With Pilot Injection for a Diesel Engine

2013 ◽  
Vol 136 (4) ◽  
Author(s):  
Long Liu ◽  
Naoto Horibe ◽  
Tatsuya Komizo ◽  
Issei Tamura ◽  
Takuji Ishiyama
Keyword(s):  
Diesel Engine ◽  
Injection Pressure ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pilot Injection ◽  
Post Injection ◽  
Spray Flames ◽  
Injection Quantity ◽  
Main Injection ◽  
Reduction Effect

With the universal utilization of the common-rail injection system in automotive diesel engines, the multistage injection strategies have become typical approaches to satisfy the increasingly stringent emission regulations, and especially the post injection has received considerable attention as an effective way for reducing the smoke emissions. Normally the post injection is applied in combination with the pilot injection to restrain the NOx emissions, smoke emissions, and combustion noise simultaneously, and the pilot injection condition affects the combustion process of the main injection and might affect the smoke reduction effect of the post injection. Thus this study aims at obtaining the post injection strategy to reduce smoke emissions in a diesel engine, where post injection is employed in combination with pilot injection. The experiments were performed using a single-cylinder diesel engine under various conditions of pilot and post injection with a constant load at an IMEP of 1.01 MPa, fixed speed of 1500 rpm, and NOx emissions concentration of 150 ± 5 ppm that was maintained by adjusting the EGR ratio. The injection pressure was set at 90 MPa at first, and then it was varied to 125 MPa to evaluate the effects of post injection on the smoke reduction in the case of higher injection pressure. The experimental results show that small post injection quantity with a short interval from the end of main injection causes less smoke emissions. And larger pilot injection quantity and later pilot injection timing lead to higher smoke emissions. And then, to explore and interpret the smoke emissions tendencies with varying pilot and post injection conditions, the experimental results of three-stage injection conditions were compared to those of two reference cases, which only included the pilot and main injection, and the interaction between main spray flames and post sprays was applied for analysis. Based on the comparative analysis, the larger smoke reduction effect of post injection was observed with the larger pilot injection quantity, while it is not greatly influenced by pilot injection timing. In addition, the smoke emissions can be reduced considerably by increasing the injection pressure, however the smoke reduction effect of post injection was attenuated. And all of these tendencies were able to be interpreted by considering the intensity variation of the interaction between main spray flames and post sprays.

Sign in / Sign up

Export Citation Format

Share Document