Analytical Prediction of Three Dimensional Cutting Process—Part 2: Chip Formation and Cutting Force with Conventional Single-Point Tool

1978 ◽  
Vol 100 (2) ◽  
pp. 229-235 ◽  
Author(s):  
E. Usui ◽  
A. Hirota
Keyword(s):  
Cutting Force ◽  
Chip Formation ◽  
Single Point ◽  
Orthogonal Cutting ◽  
Cutting Conditions ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
Analytical Prediction ◽  
Nose Radius ◽  
Cutting Model

The cutting model and the energy method to predict chip formation and cutting force, which were proposed in the previous part of this study, are extended to machining with conventional single-point tool. The prediction is always possible in the practical range of cutting conditions regardless of size of cutting and tool geometry, if only orthogonal cutting data under equivalent cutting conditions are in hand. The predicted results are verified to be in good agreement with the experimental results in a wide variety of depth of cut, side and back rake angles, side cutting edge angle, and nose radius.

Analytical Prediction of Three Dimensional Cutting Process—Part 1: Basic Cutting Model and Energy Approach

1978 ◽  
Vol 100 (2) ◽  
pp. 222-228 ◽  
Author(s):  
E. Usui ◽  
A. Hirota ◽  
M. Masuko
Keyword(s):  
Cutting Force ◽  
Chip Formation ◽  
Single Point ◽  
Orthogonal Cutting ◽  
Three Dimensional ◽  
Analytical Prediction ◽  
Forming Process ◽  
Proposed Model ◽  
Edge Based ◽  
Cutting Model

The paper proposes a new model of chip forming process in three dimensional cutting with single point tool, in which the process is interpreted as a piling up of orthogonal cuttings along the cutting edge. Based upon the proposed model, an energy method similar to the upper bound approach, which enables to predict the chip formation and the three components of cutting force by using only the orthogonal cutting data, is developed. The method is also applied to predict chip formation and cutting force in oblique cutting, plain milling, and groove cutting operations.

Chip Formation and Cutting Performance Investigation on Titanium Alloy Machining

2011 ◽  
Vol 264-265 ◽  
pp. 1062-1072
Author(s):  
Shen Yung Lin ◽  
Y.Y. Cheng ◽  
C.T. Chung
Keyword(s):  
Titanium Alloy ◽  
Cutting Force ◽  
Chip Formation ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Cutting Performance ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Chip Type ◽  
Cutting Model

First, a 2D orthogonal cutting model for titanium alloy is constructed by finite element method in this study. The cutting tool is incrementally advanced forward from an incipient stage of tool-workpiece engagement to a steady state of chip formation. Cockroft and Latham fracture criterion [1] is adopted as a chip separation criterion. By changing the settings of cutting variables such as cutting speed, depth of cut and tool rake angle to investigate the chip formation process and the variation of cutting performance during titanium cutting simulation. The changes of chip type, cutting force, effective stress/strain and cutting temperature with different cutting condition combinations are thus analyzed. The result demonstrates that the serrated chip type is obviously produced when cutting titanium alloy. Next, water-based and oil-based cutting fluids are employed in conjunction with proper cutting parameter arrangements to perform up-milling experiments. By measuring the cutting force, surface roughness and tool wear to investigate the effect of these combinations of milling variables on the variation of cutting performance for Ti-6Al-4V. The chip shape and cutting force obtained from the experiment are compared with those calculated from simulation. It is shown that there is a good agreement between simulation and experimental results.

Influence of Cutting Conditions on Chip Formation in High Speed Milling of Brittle Graphite

2014 ◽  
Vol 633-634 ◽  
pp. 769-772
Author(s):  
Li Zhou ◽  
Cheng Yong Wang ◽  
Wen Hong Li ◽  
Bai Xi Zhu ◽  
Yu Jia Zhai
Keyword(s):  
Chip Formation ◽  
High Speed ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Cutting Conditions ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
High Speed Milling ◽  
Undeformed Chip Thickness ◽  
Radial Depth

Graphite chip formation is important for the understanding of high speed milling of brittle graphite. This paper is aimed to reveal the influence of cutting conditions on the graphite chip formation in high speed milling. The relationship between the maximum undeformed chip thickness and cutting parameters was analyzed, and the influence of cutting parameters, tool geometry and milling patterns on the chip formation of brittle graphite was studied. It is concluded that the transitions of graphite chip formations were highly dependent on the undeformed chip thickness which is decided by the combination setting of feed per tooth and radial depth of cut. Big fractured block chip occurs more easily in up milling than down milling. Tool rake angle influences the chip formation according to the maximum undeformed chip thickness.

Surface Roughness and Cutting Force Components Evaluation in Hard Turning by Differently Shaped Cutting Tools

2016 ◽  
Vol 862 ◽  
pp. 26-32 ◽  
Author(s):  
Michaela Samardžiová
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Hard Turning ◽  
Cutting Tool ◽  
Single Point ◽  
Machining Process ◽  
Tool Geometry ◽  
Machined Surface ◽  
Cutting Force Components ◽  
Force Components

There is a difference in machining by the cutting tool with defined geometry and undefined geometry. That is one of the reasons of implementation of hard turning into the machining process. In current manufacturing processes is hard turning many times used as a fine finish operation. It has many advantages – machining by single point cutting tool, high productivity, flexibility, ability to produce parts with complex shapes at one clamping. Very important is to solve machined surface quality. There is a possibility to use wiper geometry in hard turning process to achieve 3 – 4 times lower surface roughness values. Cutting parameters influence cutting process as well as cutting tool geometry. It is necessary to take into consideration cutting force components as well. Issue of the use of wiper geometry has been still insufficiently researched.

OPTIMIZATION OF PROCESS PARAMETERS AFFECTING CUTTING FORCE, POWER CONSUMPTION AND SURFACE ROUGHNESS USING TAGUCHI-BASED GRAY RELATIONAL ANALYSIS IN TURNING AISI 1040 STEEL

2021 ◽  
Author(s):  
MAHIR AKGÜN
Keyword(s):  
Surface Roughness ◽  
Power Consumption ◽  
Cutting Force ◽  
Cutting Speed ◽  
System Optimization ◽  
Gray Relational Analysis ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Significance Level ◽  
Relational Analysis

This study focuses on optimization of cutting conditions and modeling of cutting force ([Formula: see text]), power consumption ([Formula: see text]), and surface roughness ([Formula: see text]) in machining AISI 1040 steel using cutting tools with 0.4[Formula: see text]mm and 0.8[Formula: see text]mm nose radius. The turning experiments have been performed in CNC turning machining at three different cutting speeds [Formula: see text] (150, 210 and 270[Formula: see text]m/min), three different feed rates [Formula: see text] (0.12 0.18 and 0.24[Formula: see text]mm/rev), and constant depth of cut (1[Formula: see text]mm) according to Taguchi L18 orthogonal array. Kistler 9257A type dynamometer and equipment’s have been used in measuring the main cutting force ([Formula: see text]) in turning experiments. Taguchi-based gray relational analysis (GRA) was also applied to simultaneously optimize the output parameters ([Formula: see text], [Formula: see text] and [Formula: see text]). Moreover, analysis of variance (ANOVA) has been performed to determine the effect levels of the turning parameters on [Formula: see text], [Formula: see text] and [Formula: see text]. Then, the mathematical models for the output parameters ([Formula: see text], [Formula: see text] and [Formula: see text]) have been developed using linear and quadratic regression models. The analysis results indicate that the feed rate is the most important factor affecting [Formula: see text] and [Formula: see text], whereas the cutting speed is the most important factor affecting [Formula: see text]. Moreover, the validation tests indicate that the system optimization for the output parameters ([Formula: see text], [Formula: see text] and [Formula: see text]) is successfully completed with the Taguchi method at a significance level of 95%.

scholarly journals Machining force comparison for surface defect hard turning and conventional hard turning of AISI 52100 steel

2021 ◽  
Vol 13 (3) ◽  
pp. 205-214
Author(s):  
P. U MAMAHESWARRAO ◽  
D. RANGARAJU ◽  
K. N. S. SUMAN ◽  
B. RAVISANKAR
Keyword(s):  
Hard Turning ◽  
Surface Defect ◽  
Cutting Speed ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Aisi 52100 ◽  
Machining Force ◽  
Aisi 52100 Steel ◽  
The Impact

In this article, a recently developed method called surface defect machining (SDM) for hard turning has been adopted and termed surface defect hard turning (SDHT). The main purpose of the present study was to explore the impact of cutting parameters like cutting speed, feed, depth of cut, and tool geometry parameters such as nose radius and negative rake angle of the machining force during surface defect hard turning (SDHT) of AISI 52100 steel in dry condition with Polycrystalline cubic boron nitride (PCBN) tool; and results were compared with conventional hard turning (CHT). Experimentation is devised and executed as per Central Composite Design (CCD) of Response Surface Methodology (RSM). Results reported that an average machining force was decreased by 22% for surface defect hard turning (SDHT) compared to conventional hard turning (CHT).

Statistical Cutting Force Model for Orthogonal Cutting of Polytetrafluoroethylene (PTFE) Composites

2013 ◽  
Author(s):  
Felicia Stan ◽  
Daniel Vlad ◽  
Catalin Fetecau
Keyword(s):  
Friction Coefficient ◽  
Cutting Force ◽  
Feed Rate ◽  
Normal Force ◽  
Polynomial Regression ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Tool Geometry ◽  
Force Model

This paper presents an experimental investigation of the cutting forces response during the orthogonal cutting of polytetrafluoroethylene (PTFE) and PTFE-based composites using the Taguchi method. Cutting experiments were conducted using the L27 orthogonal array and the effects of the cutting parameters (feed rate, cutting speed and rake angle) on the cutting force were analyzed using the S/N ratio response and the analysis of variance (ANOVA). Statistical models that correlate the cutting force with process variables were developed using ANOVA and polynomial regression. The variation of the apparent friction coefficient was analyzed with respect to tool geometry and the cutting process. The results indicated that cutting and thrust forces increase with increasing feed rate, and decrease with increasing rake angles from negative to positive values and increasing cutting speed. A power law relationship between the apparent friction coefficient and the normal force exerted by the chip on the tool-rake face was identified, the former decreasing with an increasing normal force.

Effects of Cutting Parameters on Chip Side-Curl Mechanisms and Variable Tool-Chip Contact in Turning

1999 ◽  
Author(s):  
A. K. Balaji ◽  
I. S. Jawahir
Keyword(s):  
High Speed ◽  
Cutting Parameters ◽  
Sem Analysis ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Turning Operations ◽  
Variable Friction ◽  
On Chip ◽  
Bar Turning

Abstract This paper presents the results of an investigative study on the chip side-curling mechanism and the associated variable tool-chip contact in turning operations. The effect of various cutting and tool geometry parameters such as depth of cut-nose radius ratio, feed, inclination angle, etc. on chip side-curling are established in a hierarchical manner. The importance of variable friction at the tool-chip interface along the developed length of the cutting edge is shown from the experimental observations of the tool-chip contact area using a SEM analysis. The significant influence of the radial cutting force component on the resultant chip side-curl is established using a high speed-filming analysis of comparative experiments in tube and bar turning operations.

Sign in / Sign up

Export Citation Format

Share Document