scholarly journals High Strain Rate Tensile Properties of Annealed 2 1/4 Cr-1 Mo Steel

1976 ◽  
Vol 98 (4) ◽  
pp. 361-368 ◽  
Author(s):  
R. L. Klueh ◽  
R. E. Oakes
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
High Strain Rate ◽  
Strain Rate ◽  
Tensile Properties ◽  
Elevated Temperatures ◽  
High Strain ◽  
Total Elongation ◽  
Major Effect ◽  
Dynamic Strain

The high strain rate tensile properties of annealed 2 1/4 Cr-1 Mo steel were determined and the tensile behavior from 25 to 566°C and strain rates of 2.67 × 10−6 to 144/s were described. Above 0.1/s at 25°C, both the yield stress and the ultimate tensile strength increased rapidly with increasing strain rate. As the temperature was increased, a dynamic strain aging peak appeared in the ultimate tensile strength-temperature curves. The peak height was a maximum at about 350°C and 2.67 × 10−6/s. With increasing strain rate, a peak of decreased height occurred at progressively higher temperatures. The major effect of strain rate on ductility occurred at elevated temperatures, where a decrease in strain rate caused an increase in total elongation and reduction in area.

Strain Rate Effects on the Elevated-Temperature Tensile Behavior of a Bainitic 2-1/4 Cr-1 Mo Steel

1977 ◽  
Vol 99 (4) ◽  
pp. 350-358 ◽  
Author(s):  
R. L. Klueh ◽  
R. E. Oakes
Keyword(s):  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Strain Rate ◽  
Yield Stress ◽  
Uniform Elongation ◽  
Constant Strain Rate ◽  
Total Elongation ◽  
Dynamic Strain ◽  
Strain Rate Effects ◽  
Reduction Of Area

The tensile properties of a normalized-and-tempered 2-1/4 Cr-1 Mo steel were determined from 25 to 566° C and the strain rate 2.67 × 10−6 to 144/s. The specimens were taken from a 1-in. thick plate and had a microstructure that was essentially 100 percent bainite. Except at 25 and 566° C, the 0.2 percent yield stress was little affected by strain rate; at 25 and 566° C, the yield stress increased with increasing strain rate. At a constant strain rate, the yield stress decreased with increasing temperature. The effect of strain rate and temperature on the ultimate tensile strength was somewhat more complicated. A strength peak that resulted from dynamic strain aging was observed in the ultimate tensile strength-temperature relationship. The position of these peaks moved to higher temperatures with increasing strain rate. Total elongation and reduction of area were relatively constant over the range of test variables, except at 566° C, where they increased with decreasing strain rate. However, uniform elongation decreased with decreasing strain rate at 510 and 566° C, dropping to 1 and 0.6 percent, respectively.

Impact tensile behavior and frequency response of 3D braided composites

2011 ◽  
Vol 82 (3) ◽  
pp. 280-287 ◽  
Author(s):  
Xuehui Gan ◽  
Jianhua Yan ◽  
Bohong Gu ◽  
Baozhong Sun
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Tensile Properties ◽  
High Strain ◽  
Tensile Modulus ◽  
Tensile Failure ◽  
Uniaxial Tensile ◽  
Strain Rates ◽  
Braided Composites ◽  
3D Braided Composites

The uniaxial tensile properties of 4-step 3D braided E-glass/epoxy composites under quasi-static and high-strain rate loadings have been investigated to evaluate the tensile failure mode at different strain rates. The uniaxial tensile properties at high strain rates from 800/s to 2100/s were tested using the split Hopkinson tension bar (SHTB) technique. The tensile properties at quasi-static strain rate were also tested and compared with those in high strain rates. Z-transform theory is applied to 3D braided composites to characterize the system dynamic behaviors in frequency domain. The frequency responses and the stability of 3D braided composites under quasi-static and high-strain rate compression have been analyzed and discussed in the Z-transform domain. The results indicate that the stress-strain curves are rate sensitive, and tensile modulus, maximum tensile stress and corresponding tensile strain are also sensitive to the strain rate. The tensile modulus, maximum tensile stress of the 3D braided composites are linearly increased with the strain rate. With increasing of the strain rate (from 0.001/s to 2100/s), the tensile failure of the 3D braided composite specimens has a tendency of transition from ductile failure to brittle failure. The magnitude response and phase response is very different in quasi-static loading with that in high-strain rate loading. The 3D braided composite system is more stable at high strain rate than quasi-static loading.

scholarly journals High Strain-Rate Compressive Properties of Carbon/Epoxy Laminated Composites – Effects of loading direction and temperature

2018 ◽  
Vol 183 ◽  
pp. 02011
Author(s):  
Kenji Nakai ◽  
Tsubasa Fukushima ◽  
Takashi Yokoyama ◽  
Kazuo Arakawa
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Elevated Temperatures ◽  
High Strain ◽  
Split Hopkinson Pressure Bar ◽  
Slenderness Ratio ◽  
Testing Machine ◽  
Negative Temperature ◽  
Hopkinson Pressure Bar ◽  
Instron Testing Machine

The high strain-rate compressive characteristics of a cross-ply carbon/epoxy laminated composite in the three principal material directions or fibre (1-), in-plane transverse (2-) and throughthickness (3-) directions are investigated on the conventional split Hopkinson pressure bar (SHPB) over a range of temperatures between 20 and 80 °C. A nearly 10 mm thick cross-ply carbon/epoxy composite laminate fabricated using vacuum assisted resin transfer molding (VaRTM) was tested. Cylindrical specimens with a slenderness ratio (= length/diameter) of 0.5 are used in high strain-rate tests, and those with the slenderness ratios of 1.0 and 1.5 are used in low and intermediate strain-rate tests. The uniaxial compressive stress-strain curves up to failure at quasi-static and intermediate strain rates are measured on an Instron testing machine at elevated temperatures. A pair of steel rings is attached to both ends of the cylindrical specimens to prevent premature end crushing in the 1-and 2-direction tests on the Instron testing machine. It is shown that the ultimate compressive strength (or failure stress) exhibits positive strainrate effects and negative temperature ones over a strain-rate range of 10–3 to 103/s and a temperature range of 20 to 80 °C in the three principal material directions.

An Alternate Approach to SHPB Tests to Compute Johnson-Cook Material Model Constants for 97 WHA at High Strain Rates and Elevated Temperatures Using Machining Tests

2020 ◽  
Vol 143 (2) ◽  
Author(s):  
Chithajalu Kiran Sagar ◽  
Amrita Priyadarshini ◽  
Amit Kumar Gupta ◽  
Tarun Kumar ◽  
Shreya Saxena
Keyword(s):  
Finite Element ◽  
High Strain Rate ◽  
Strain Rate ◽  
Elevated Temperatures ◽  
High Strain ◽  
Optimization Technique ◽  
Material Model ◽  
Computational Techniques ◽  
Fe Model

Abstract With advances in computational techniques, numerical methods such as finite element method (FEM) are gaining much of the popularity for analysis as these substitute the expensive trial and error experimental techniques to a great extent. Consequently, selection of suitable material models and determination of precise material model constants are one of the prime concerns in FEM. This paper presents a methodology to determine the Johnson-Cook constitutive equation constants (JC constants) of 97 W Tungsten heavy alloys (WHAs) under high strain rate conditions using machining tests in conjunction with Oxley’s predictive model and particle swarm optimization (PSO) algorithm. Currently, availability of the high strain rate data for 97 WHA are limited and consequently, JC constants for the same are not readily available. The overall methodology includes determination of three sets of JC constants, namely, M1 and M2 from the Split-Hopkinson pressure bar (SHPB) test data available in literature by using conventional optimization technique and artificial bee colony (ABC) algorithm, respectively. However, M3 is determined from machining tests using inverse identification method. To validate the identified JC constants, machining outputs (cutting forces, temperature, and shear strain) are predicted using finite element (FE) model by considering M1, M2, and M3 as input under different cutting conditions and then validated with corresponding experimental values. The predicted outputs obtained using JC constants M3 closely matched with that of the experimental ones with error percentage well within 10%.

scholarly journals An Image-Based Impact Test for the High Strain Rate Tensile Properties of Brittle Materials

2018 ◽  
Vol 183 ◽  
pp. 02042
Author(s):  
Lloyd Fletcher ◽  
Fabrice Pierron
Keyword(s):  
Tensile Strength ◽  
Elastic Modulus ◽  
High Strain Rate ◽  
Strain Rate ◽  
Stress Wave ◽  
High Strain ◽  
Brittle Materials ◽  
Test Method ◽  
Strain Rates ◽  
High Strain Rates

Testing ceramics at high strain rates presents many experimental diffsiculties due to the brittle nature of the material being tested. When using a split Hopkinson pressure bar (SHPB) for high strain rate testing, adequate time is required for stress wave effects to dampen out. For brittle materials, with small strains to failure, it is difficult to satisfy this constraint. Because of this limitation, there are minimal data (if any) available on the stiffness and tensile strength of ceramics at high strain rates. Recently, a new image-based inertial impact (IBII) test method has shown promise for analysing the high strain rate behaviour of brittle materials. This test method uses a reflected compressive stress wave to generate tensile stress and failure in an impacted specimen. Throughout the propagation of the stress wave, full-field displacement measurements are taken, from which strain and acceleration fields are derived. The acceleration fields are then used to reconstruct stress information and identify the material properties. The aim of this study is to apply the IBII test methodology to analyse the stiffness and strength of ceramics at high strain rates. The results show that it is possible to identify the elastic modulus and tensile strength of tungsten carbide at strain rates on the order of 1000 s-1. For a tungsten carbide with 13% cobalt binder the elastic modulus was identified as 516 GPa and the strength was 1400 MPa. Future applications concern boron carbide and sapphire, for which limited data exist in high rate tension.

scholarly journals Highly ductile amorphous oxide at room temperature and high strain rate

Science ◽  
2019 ◽  
Vol 366 (6467) ◽  
pp. 864-869 ◽  
Author(s):  
Erkka J. Frankberg ◽  
Janne Kalikka ◽  
Francisco García Ferré ◽  
Lucile Joly-Pottuz ◽  
Turkka Salminen ◽  
...  
Keyword(s):  
High Strain Rate ◽  
Strain Rate ◽  
Room Temperature ◽  
High Strain ◽  
Total Elongation ◽  
Modern World ◽  
Mechanical Resistance ◽  
Oxide Glasses ◽  
Amorphous Oxide ◽  
Damage Tolerant

Oxide glasses are an integral part of the modern world, but their usefulness can be limited by their characteristic brittleness at room temperature. We show that amorphous aluminum oxide can permanently deform without fracture at room temperature and high strain rate by a viscous creep mechanism. These thin-films can reach flow stress at room temperature and can flow plastically up to a total elongation of 100%, provided that the material is dense and free of geometrical flaws. Our study demonstrates a much higher ductility for an amorphous oxide at low temperature than previous observations. This discovery may facilitate the realization of damage-tolerant glass materials that contribute in new ways, with the potential to improve the mechanical resistance and reliability of applications such as electronic devices and batteries.

Tensile strength of aluminum-epoxy resin composite structure under high strain rate conditions

2012 ◽  
Author(s):  
Damien Laporte ◽  
Frederic Malaise ◽  
Michel Boustie ◽  
Jean-Marc Chevalier ◽  
Eric Buzaud
Keyword(s):  
Tensile Strength ◽  
High Strain Rate ◽  
Strain Rate ◽  
Epoxy Resin ◽  
Composite Structure ◽  
High Strain ◽  
Resin Composite ◽  
Epoxy Resin Composite
Sign in / Sign up

Export Citation Format

Share Document