Flow Parameters in Hydrostatic Lubrication for Several Bearing Shapes

1960 ◽  
Vol 82 (2) ◽  
pp. 257-264 ◽  
Author(s):  
S. Raynor ◽  
A. Charnes
Keyword(s):  
Conformal Mapping ◽  
Film Thickness ◽  
Flow Rate ◽  
Carrying Capacity ◽  
Load Carrying Capacity ◽  
Total Load ◽  
Thrust Bearings ◽  
Flow Parameters ◽  
Load Carrying ◽  
Mapping Techniques

In the case of hydrostatic lubrication the designer of thrust bearings has to make decisions regarding the shape of pads, location of oil holes, and configuration of oil grooves. In this paper several pad shapes and associated oil inlets were investigated using conformal mapping techniques to obtain the total load-carrying capacity, flow rate of oil, oil-film thickness, pressure and velocity distribution. The results of these calculations permit the designer to approximate his chosen configuration by computed models in order to estimate the flow parameters.

The Impact of Linear Deformations on Stationary Hydrostatic Thrust Bearings

2002 ◽  
Vol 124 (4) ◽  
pp. 874-877 ◽  
Author(s):  
Noah D. Manring ◽  
Robert E. Johnson ◽  
Harish P. Cherukuri
Keyword(s):  
Pressure Distribution ◽  
Closed Form ◽  
Flow Rate ◽  
Carrying Capacity ◽  
Thrust Bearing ◽  
Load Carrying Capacity ◽  
Thrust Bearings ◽  
Load Carrying ◽  
Number Flow ◽  
The Impact

In this work, the operating sensitivity of the hydrostatic thrust bearing with respect to pressure-induced deformations will be studied in a stationary setting. Using the classical lubrication equations for low Reynold’s number flow, closed-form expressions are generated for describing the pressure distribution, the flow rate, and the load carrying capacity of the bearing. These expressions are developed to consider deformations of the bearing that result in either concave or convex shapes relative to a flat thrust surface. The impact of both shapes is compared, and the sensitivity of the flow rate and the load carrying capacity of the bearing with respect to the magnitude of the deformation is discussed. In summary, it is shown that all deformations increase the flow rate of the bearing and that concave deformations increase the load carrying capacity while convex deformations decrease this same quantity relative to a non-deformed bearing condition.

Computational Fluid Dynamics Thermohydrodynamic Analysis of Three-Dimensional Sector-Pad Thrust Bearings With Rectangular Dimples

2013 ◽  
Vol 136 (1) ◽  
Author(s):  
C. I. Papadopoulos ◽  
L. Kaiktsis ◽  
M. Fillon
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Carrying Capacity ◽  
Thermal Effects ◽  
Operating Conditions ◽  
Load Carrying Capacity ◽  
Performance Indices ◽  
Thrust Bearings ◽  
Load Carrying ◽  
Texture Design

The paper presents a detailed computational study of flow patterns and performance indices in a dimpled parallel thrust bearing. The bearing consists of eight pads; the stator surface of each pad is partially textured with rectangular dimples, aiming at maximizing the load carrying capacity. The bearing tribological performance is characterized by means of computational fluid dynamics (CFD) simulations, based on the numerical solution of the Navier–Stokes and energy equations for incompressible flow. Realistic boundary conditions are implemented. The effects of operating conditions and texture design are studied for the case of isothermal flow. First, for a reference texture pattern, the effects of varying operating conditions, in particular minimum film thickness (thrust load), rotational speed and feeding oil pressure are investigated. Next, the effects of varying texture geometry characteristics, in particular texture zone circumferential/radial extent, dimple depth, and texture density on the bearing performance indices (load carrying capacity, friction torque, and friction coefficient) are studied, for a representative operating point. For the reference texture design, the effects of varying operating conditions are further investigated, by also taking into account thermal effects. In particular, adiabatic conditions and conjugate heat transfer at the bearing pad are considered. The results of the present study indicate that parallel thrust bearings textured by proper rectangular dimples are characterized by substantial load carrying capacity levels. Thermal effects may significantly reduce load capacity, especially in the range of high speeds and high loads. Based on the present results, favorable texture designs can be assessed.

Numerical investigation of squeeze film lubrication on bioinspired hexagonal patterned surface

2022 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Binbin Su ◽  
Xianghe Zou ◽  
Lirong Huang
Keyword(s):  
Flow Rate ◽  
Carrying Capacity ◽  
Squeeze Film ◽  
Load Carrying Capacity ◽  
Two Dimensional ◽  
Working Mechanism ◽  
Content Type ◽  
Patterned Surface ◽  
Load Carrying ◽  
Film Lubrication

Purpose This paper aims to investigate the squeeze film lubrication properties of hexagonal patterned surface inspired by the epidermis structure of tree frog’s toe pad and numerically explore the working mechanism of hexagonal micropillar during the acquisition process of high adhesive and friction for wet contacts. Design/methodology/approach A two-dimensional elastohydrodynamic numerical model is employed for the squeezing contacts. The pressure distribution, load carrying capacity and liquid flow rate of the squeeze film are obtained through a simultaneous solution of the two-dimensional Reynolds equation and elasticity deformation equations. Findings Higher pressure is found to be longitudinally distributed across individual hexagonal pillar, with pressure peak emerging at the center of hexagonal pillar. Expanding the area density and shrinking the channel depth or initial film thickness will improve the magnitude of squeezing pressure. Relatively lower pressure is generated inside interconnected channels, which reduces the load carrying capacity of the squeeze film. Meanwhile, the introduction of microchannel is revealed to downscale the total mass flow rate of squeezing contacts. Originality/value This paper provides a good proof for the working mechanism of surface microstructures during the acquisition process of high adhesive and friction for wet contacts.

Density Variation Effects in Stepped-Thrust Bearings

1959 ◽  
Vol 26 (3) ◽  
pp. 337-340
Author(s):  
C. F. Kettleborough
Keyword(s):  
Coefficient Of Friction ◽  
Carrying Capacity ◽  
Thrust Bearing ◽  
Density Variation ◽  
Load Carrying Capacity ◽  
Thrust Bearings ◽  
Load Carrying ◽  
The Coefficient Of Friction

Abstract The problem of the stepped-thrust bearing is considered but, whereas normally volumetric continuity is assumed, the equations are solved assuming mass continuity; i.e., the variation of density is also considered as well as the effect of the stepped discontinuity on the load-carrying capacity and the coefficient of friction. Computed theoretical curves illustrate the importance of the density on the operation of this bearing and, in part, explain results already published.

The Performance of Hydrodynamic Lubricating Films With Viscosity Variations Perpendicular to the Direction of Motion

1972 ◽  
Vol 94 (1) ◽  
pp. 44-48 ◽  
Author(s):  
E. B. Qvale ◽  
F. R. Wiltshire
Keyword(s):  
Film Thickness ◽  
Carrying Capacity ◽  
Load Carrying Capacity ◽  
End Effects ◽  
Parametric Curves ◽  
One Dimensional ◽  
Lubricating Film ◽  
Families Of Curves ◽  
Load Carrying ◽  
The Coefficient Of Friction

The effects of prescribed viscosity variations across a hydrodynamic lubricating film are studied. The film is strictly one dimensional and end effects are neglected. The viscosity variations are given by three families of curves. The considerable decreases (in the limit 100 percent) and occasional increases in the coefficient of friction that can occur for constant film thickness and load-carrying capacity are evaluated and the results are presented in terms of parametric curves. Important physical situations where these viscosity variations may be observed or produced are described.

A Theory of Liquid-Solid Lubrication in Elastohydrodynamic Regime

1989 ◽  
Vol 111 (3) ◽  
pp. 440-444 ◽  
Author(s):  
M. M. Khonsari ◽  
S. H. Wang ◽  
Y. L. Qi
Keyword(s):  
Particle Size ◽  
Film Thickness ◽  
Carrying Capacity ◽  
Theoretical Study ◽  
Solid Particles ◽  
Solid Lubrication ◽  
Load Carrying Capacity ◽  
Line Contact ◽  
Load Carrying ◽  
Bounding Surfaces

A theoretical study of the effectiveness of solid particles dispersed in oil in the elastohydrodynamic line contact is presented. The analysis includes the variation of the viscosity and density of the lubricant as a function of pressure. The deformation of solid particles and that of the bounding surfaces are taken into consideration. Results are presented for the variation of the film thickness and the load carrying capacity as a function of the particle size, concentration, and properties of various types of particles.

The limiting load-carrying capacity of foil thrust bearings

2017 ◽  
Vol 232 (8) ◽  
pp. 1046-1052
Author(s):  
P Samanta ◽  
MM Khonsari
Keyword(s):  
Analytical Solution ◽  
Carrying Capacity ◽  
Simple Procedure ◽  
Load Carrying Capacity ◽  
Thrust Bearings ◽  
Limiting Load ◽  
Load Carrying ◽  
Closed Form Analytical Solution ◽  
Foil Thrust Bearing ◽  
Thrust Load

A simple procedure is proposed for predicting the limiting pressure and corresponding limiting of the load-carrying capacity of a foil thrust bearing. A closed-form analytical solution for the limiting load is derived, and the predictions are verified by the numerical solution. An approximate solution for limiting thrust load is also obtained and compared to the value obtained through the analytical solution. A parametric analysis is performed to examine the dependency of the limiting load on different geometric parameters for the bearing.

Geometry Optimization of Textured Three-Dimensional Micro- Thrust Bearings

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
C. I. Papadopoulos ◽  
E. E. Efstathiou ◽  
P. G. Nikolakopoulos ◽  
L. Kaiktsis
Keyword(s):  
Carrying Capacity ◽  
Stokes Equations ◽  
Load Capacity ◽  
Three Dimensional ◽  
Load Carrying Capacity ◽  
Thrust Bearings ◽  
Micro Channels ◽  
Wide Range ◽  
Load Carrying ◽  
Bearing Load

This paper presents an optimization study of the geometry of three-dimensional micro-thrust bearings in a wide range of convergence ratios. The optimization goal is the maximization of the bearing load carrying capacity. The bearings are modeled as micro-channels, consisting of a smooth moving wall (rotor), and a stationary wall (stator) with partial periodic rectangular texturing. The flow field is calculated from the numerical solution of the Navier-Stokes equations for incompressible isothermal flow; processing of the results yields the bearing load capacity and friction coefficient. The geometry of the textured channel is defined parametrically for several width-to-length ratios. Optimal texturing geometries are obtained by utilizing an optimization tool based on genetic algorithms, which is coupled to the CFD code. Here, the design variables define the bearing geometry and convergence ratio. To minimize the computational cost, a multi-objective approach is proposed, consisting in the simultaneous maximization of the load carrying capacity and minimization of the bearing convergence ratio. The optimal solutions, identified based on the concept of Pareto dominance, are equivalent to those of single-objective optimization problems for different convergence ratio values. The present results demonstrate that the characteristics of the optimal texturing patterns depend strongly on both the convergence ratio and the width-to-length ratio. Further, the optimal load carrying capacity increases at increasing convergence ratio, up to an optimal value, identified by the optimization procedure. Finally, proper surface texturing provides substantial load carrying capacity even for parallel or slightly diverging bearings. Based on the present results, we propose simple formulas for the design of textured micro-thrust bearings.

Sign in / Sign up

Export Citation Format

Share Document