Residual Stress Distribution in Hard-Facing of Pressure Relief Valve Seat

2014 ◽  
Vol 136 (6) ◽  
Author(s):  
Li Ai ◽  
Xinhai Yu ◽  
Wenchun Jiang ◽  
Wanchuck Woo ◽  
Xiaofeng Ze ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Infrared Imaging ◽  
Element Model ◽  
Pressure Relief Valve ◽  
Stress Distributions ◽  
Relief Valve ◽  
Pressure Relief

In this study, for the hard-facing of spring-loaded pressure relief valve seats, the residual stress distributions after the tungsten inert gas welding, (TIG) postwelded heat treatment and subsequent surface turning were investigated. The heat input parameters of welding were calibrated using an infrared imaging and thermocouples. The residual stress distributions were computed using three-dimensional finite element model. The neutron diffraction approach was employed to verify the finite element calculation. It is found that, the surface temperature during hard-facing welding shows a double ellipsoidal shape with the highest value of around 1570 °C. The high residual stress zones are located exactly under the welded joint except a slight deviation in the hoop direction. The magnitudes of tensile residual stresses in the three directions increase with their corresponding locations from the root of the joint into the base metal. The residual stresses in all of the three directions decrease significantly after the heat treatment. After surface turning, the residual stresses are tensile except for those close to the inner surface that are compressive in axial and radial directions.

Evaluation of Through-Thickness Residual Stresses by Neutron Diffraction and Finite-Element Method in Thick Weld Plates

2016 ◽  
Vol 139 (3) ◽  
Author(s):  
Wenchun Jiang ◽  
Wanchuck Woo ◽  
Yu Wan ◽  
Yun Luo ◽  
Xuefang Xie ◽  
...  
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Neutron Diffraction ◽  
Residual Stresses ◽  
Plate Thickness ◽  
Element Model ◽  
Stress Distributions ◽  
Thick Plates ◽  
Work Hardening Model ◽  
Generalized Plane Strain

Through-thickness distributions of the welding residual stresses were studied in the range of 50–100 mm thick plates by using finite-element modeling (FEM) and neutron diffraction measurements. In order to simulate the residual stresses through the thickness of the thick weld joints, this paper proposes a two-dimensional generalized plane strain (GPS) finite-element model coupled with the mixed work hardening model. The residual stress distributions show mostly asymmetric parabola profiles through the thickness of the welds and it is in good correlation with the neutron diffraction results. Both the heat input and plate thickness have little influence on the residual stress distributions due to the relatively large constraints of the thick specimen applied for each welding pass. A general formula has been suggested to evaluate the distributions of the through-thickness residual stresses in thick welds based on FEM and neutron diffraction experimental results.

Effects of Repair Weld Length on Residual Stress Distribution

2001 ◽  
Vol 124 (1) ◽  
pp. 74-80 ◽  
Author(s):  
P. Dong ◽  
J. Zhang ◽  
P. J. Bouchard
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Axial Stress ◽  
Base Material ◽  
Shell Element ◽  
Element Model ◽  
Outer Diameter ◽  
Stress Distributions ◽  
Axial Tensile

This paper discusses residual stress distributions induced by repairing a stainless steel girth weld in a 19-mm thick pipe of outer diameter 541 mm. In particular, the effects of repair weld circumferential length are examined using finite element modeling. Results for three different repair lengths are presented having circumferential angular spans of 20 deg (short repair), 57 deg (medium repair), and 114 deg (long repair). A special 3-D shell element model is used which facilitates the simulation of multi-pass welds in 3-D piping components. The results shed light on a number of important 3-D residual stress features associated with repairs. Outer surface axial residual stresses in the weld and adjacent base material are tensile along the length of the repair, reach maxima values near the arc start/stop positions, and then drop into compression beyond the repair ends. The short repair develops the highest axial tensile stresses due to the overlay of start/stop effects. The circumferentially remote residual stresses are unaffected by the repairs. At midlength of the repair, profiles of axial stress along the pipe show tensile peaks at ≈40 mm away from the weld centerline; these peaks decrease in magnitude with increasing repair length. However, the medium repair axial stresses show the greatest range of influence along the pipe. The pre-existing original girth weld residual stresses have very little effect on the repair residual stress characteristics. Finally, residual stress measurements on mock-up components are discussed which confirm the validity of the finite element methods used.

Stress and Fatigue Life Modeling of Cannon Breech Closures Including Effects of Material Strength and Residual Stress

2000 ◽  
Vol 123 (1) ◽  
pp. 150-154
Author(s):  
John H. Underwood ◽  
Michael J. Glennon
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Fatigue Life ◽  
Yield Strength ◽  
Residual Stresses ◽  
Solid Mechanics ◽  
Element Model ◽  
Pressure Vessels ◽  
Material Strength ◽  
Element Analysis

Laboratory fatigue life results are summarized from several test series of high-strength steel cannon breech closure assemblies pressurized by rapid application of hydraulic oil. The tests were performed to determine safe fatigue lives of high-pressure components at the breech end of the cannon and breech assembly. Careful reanalysis of the fatigue life tests provides data for stress and fatigue life models for breech components, over the following ranges of key parameters: 380–745 MPa cyclic internal pressure; 100–160 mm bore diameter cannon pressure vessels; 1040–1170 MPa yield strength A723 steel; no residual stress, shot peen residual stress, overload residual stress. Modeling of applied and residual stresses at the location of the fatigue failure site is performed by elastic-plastic finite element analysis using ABAQUS and by solid mechanics analysis. Shot peen and overload residual stresses are modeled by superposing typical or calculated residual stress distributions on the applied stresses. Overload residual stresses are obtained directly from the finite element model of the breech, with the breech overload applied to the model in the same way as with actual components. Modeling of the fatigue life of the components is based on the fatigue intensity factor concept of Underwood and Parker, a fracture mechanics description of life that accounts for residual stresses, material yield strength and initial defect size. The fatigue life model describes six test conditions in a stress versus life plot with an R2 correlation of 0.94, and shows significantly lower correlation when known variations in yield strength, stress concentration factor, or residual stress are not included in the model input, thus demonstrating the model sensitivity to these variables.

scholarly journals X-ray nanodiffraction analysis of stress oscillations in a W thin film on through-silicon via

2016 ◽  
Vol 49 (1) ◽  
pp. 182-187 ◽  
Author(s):  
J. Todt ◽  
H. Hammer ◽  
B. Sartory ◽  
M. Burghammer ◽  
J. Kraft ◽  
...  
Keyword(s):  
Thin Film ◽  
Residual Stress ◽  
Finite Element ◽  
Diffraction Data ◽  
Element Model ◽  
Stress Distributions ◽  
Through Silicon Via ◽  
X Ray ◽  
Tangential Stresses ◽  
Stress Components

Synchrotron X-ray nanodiffraction is used to analyse residual stress distributions in a 200 nm-thick W film deposited on the scalloped inner wall of a through-silicon via. The diffraction data are evaluated using a novel dedicated methodology which allows the quantification of axial and tangential stress components under the condition that radial stresses are negligible. The results reveal oscillatory axial stresses in the range of ∼445–885 MPa, with a distribution that correlates well with the scallop wavelength and morphology, as well as nearly constant tangential stresses of ∼800 MPa. The discrepancy with larger stress values obtained from a finite-element model, as well as from a blanket W film, is attributed to the morphology and microstructural nature of the W film in the via.

Finite Element Analysis of Effects of Preheating and Postweld Heat Treatment on Residual Stress in Pipe Welding

2011 ◽  
Vol 314-316 ◽  
pp. 428-431 ◽  
Author(s):  
Hui Du ◽  
Dong Po Wang ◽  
Chun Xiu Liu ◽  
Hai Zhang
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Finite Element ◽  
Stress Distribution ◽  
Welding Process ◽  
Postweld Heat Treatment ◽  
Element Model ◽  
Element Analysis ◽  
Pipe Welding ◽  
Postweld Heat

To simulate preheating and postweld heat treatment of Q345 steel pipe welding, the finite element model was established. The welding process was simulated by method of the ANSYS element birth and death technique. In this paper, to obtain the distribution of the temperature field and stress field in different situations, preheating processes with two different values of temperature and postweld heat treatment process were simulated respectively. The results show that preheating can homogenize residual stress distribution of the weldment and decrease the residual stress. The heat treatment reduces the residual stress in inner and outer walls by 24% and 70% respectively and the stress distribution is more even and stress concentration is reduced.

scholarly journals A Finite Element Study of the Residual Stress and Deformation in Hemispherical Contacts

2005 ◽  
Vol 127 (3) ◽  
pp. 484-493 ◽  
Author(s):  
Robert Jackson ◽  
Itti Chusoipin ◽  
Itzhak Green
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Yield Criterion ◽  
Contact Region ◽  
Element Model ◽  
Von Mises Stress ◽  
Contact Radius ◽  
Perfectly Plastic ◽  
Von Mises

This work presents a finite element model (FEM) of the residual stresses and strains that are formed after an elastoplastic hemispherical contact is unloaded. The material is modeled as elastic perfectly plastic and follows the von Mises yield criterion. The FEM produces contours for the normalized axial and radial displacements as functions of the removed interference depth and location on the surface of the hemisphere. Contour plots of the von Mises stress and other stress components are also presented to show the formation of the residual stress distribution with increasing plastic deformation. This work shows that high residual von Mises stresses appear in the material pileup near the edge of the contact area after complete unloading. Values are defined for the minimum normalized interference, that when removed, results in plastic residual stresses. This work also defines an interference at which the maximum residual stress transitions from a location below the contact region and along the axis of symmetry to one near to the surface at the edge of the contact radius (within the pileup).

A Three-Dimensional Finite Element Evaluation of a Destructive Experimental Method for Determining Through-Thickness Residual Stresses in Girth Welded Pipes

1986 ◽  
Vol 108 (2) ◽  
pp. 99-106 ◽  
Author(s):  
E. F. Rybicki ◽  
J. R. Shadley
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Experimental Method ◽  
Three Dimensional ◽  
Element Model ◽  
Stress Distributions ◽  
Reference Stress ◽  
Improvement Process ◽  
Dimensional Finite Element ◽  
Three Dimensional Finite Element

The accuracy of a destructive, experimental method for the evaluation of through-thickness residual stress distributions is investigated. The application of the method is to a welded pipe that has been subjected to a residual stress improvement process. The residual stress improvement process introduces gradients in the stress distribution. The question of interest is how well the back-computation method used to interpret the experimental data represents the residual stress distribution for this type of stress profile. To address this question, a finite element model was used to provide a reference stress solution for comparison with the back-computation results of the experimental method. Three-dimensional finite element stress analyses were also conducted to simulate the cutting steps of the destructive laboratory procedure. The residual stress distributions obtained by the back-computation procedure were then compared with the reference stress solutions provided by the finite element model. The comparisons show agreement and indicate that good results can be expected from the experimental method when it is applied to a pipe that has been subjected to a residual stress improvement process, provided that the axial gradient of stress is not too large.

scholarly journals Finite Element Prediction of Residual Stress Distributions in a Multipass Welded Piping Branch Junction

2006 ◽  
Author(s):  
Wei Jiang ◽  
Kadda Yahiaoui
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Welding Process ◽  
Pressure Vessels ◽  
Welding Residual Stress ◽  
Stress Distributions ◽  
Multipass Welding ◽  
Hexahedral Elements ◽  
Element Removal

Piping branch junctions and nozzle attachments to main pressure vessels are common engineering components used in the power, oil and gas, and shipbuilding industries amongst others. These components are usually fabricated by multipass welding. The latter process is known to induce residual stresses at the fabrication stage which can have severe adverse effects on the in-service behavior of such critical components. It is thus desirable if the distributions of residual stresses can be predicted well in advance of welding execution. This paper presents a comprehensive study of three dimensional residual stress distributions in a stainless steel tee branch junction during a multipass welding process. A full 3D thermo-mechanical finite element model has been developed for this purpose. A newly developed meshing technique has been used to model the complex intersection areas of the welded junction with all hexahedral elements. Element removal/reactivate technique has been employed to simulate the deposition of filler material. Material, geometry and boundary nonlinearities associated with welding were all taken into account. The analysis results are presented in the form of stress distributions circumferentially along the weldline on both run and branch pipes as well as at the run and branch cross sections. In general, this computational model is capable of predicting 3D through thickness welding residual stress, which can be valuable for structural integrity assessments of complex welded geometries.

Residual Stresses in Butt Welding of Two Circular Pipes: An Experimental and Numerical Investigation

2014 ◽  
Author(s):  
Gurinder Singh Brar
Keyword(s):  
Finite Element Method ◽  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Finite Element Model ◽  
Welding Process ◽  
Diffraction Method ◽  
Element Model ◽  
X Ray Diffraction ◽  
X Ray

Welding is a reliable and efficient joining process in which the coalescence of metals is achieved by fusion. Welding is carried out with a very complex thermal cycle which results in irreversible elastic-plastic deformation and residual stresses in and around fusion zone and heat affected zone (HAZ). A residual stress due to welding arises from the differential heating of the plates due to the weld heat source. Residual stresses may be an advantage or disadvantage in structural components depending on their nature and magnitude. The beneficial effect of these compressive stresses have been widely used in industry as these are believed to increase fatigue strength of the component and reduce stress corrosion cracking and brittle fracture. But due to the presence of residual stresses in and around the weld zone the strength and life of the component is also reduced. To understand the behavior of residual stresses, two 10 mm thick Fe410WC mild steel plates are butt welded using the Metal Active Gas (MAG) process. An experimental method (X-ray diffraction) and numerical analysis (finite element analysis) were then carried out to calculate the residual stress values in the welded plates. Three types of V-butt weld joint — two-pass, three-pass and four-pass were considered in this study. In multi-pass welding operation the residual stress pattern developed in the material changes with each weld pass. In X-ray diffraction method, the residual stresses were derived from the elastic strain measurements using a Young’s modulus value of 210 GPa and Poisson’s ratio of 0.3. Finite element method based, SolidWorks software was used to develop coupled thermal-mechanical three dimension finite element model. The finite element model was evaluated for the transient temperatures and residual stresses during welding. Also variations of the physical and mechanical properties of material with the temperature were taken into account. The numerical results for peak transverse residual stresses attained in the welded plates for two-pass, three-pass and four-pass welded joint were 67.7 N/mm2, 58.6 N/mm2, and 48.1 N/mm2 respectively. The peak temperature attained during welding process comes out to be 970°C for two-pass weld, 820.8°C for three-pass weld and 651.9°C for four-pass weld. It can be concluded that due to increase in the number of passes during welding process or deposition weld beads, the residual stresses and temperature distribution decrease. Also, the results obtained by finite element method agree well with those from experimental X-ray diffraction method.

Sign in / Sign up

Export Citation Format

Share Document