Trapped Unburned Fuel Estimation and Robustness Analysis for a Turbocharged Diesel Engine With Negative Valve Overlap Strategy

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Song Chen ◽  
Fengjun Yan
Keyword(s):  
Theoretical Analysis ◽  
Internal Combustion Engines ◽  
Combustion Process ◽  
Robustness Analysis ◽  
Linear Matrix ◽  
Fuel Mass ◽  
Residual Gas ◽  
Unburned Fuel ◽  
Negative Valve Overlap ◽  
Valve Overlap

Turbocharger and negative valve overlap (NVO) strategy are widely used among advanced combustion modes for internal combustion engines. In order to achieve well emission performance, the NVO can be as large as 100 crank angle (CA) degrees, such that the residual gas fraction can be up to 40%. With such amount of residual gas in the cylinder, the trapped unburned fuel is not trivial. It has a significant impact on the combustion process. However, the trapped unburned fuel mass is hard to be measured directly. In this paper, a novel method based on the signals of oxygen fraction is proposed to estimate it. By analyzing the combustion process, dynamic equations for the intake/exhaust manifolds and in-cylinder oxygen fractions, as well as actual fuel mass in the cylinder are constructed. A smooth variable structure filter (SVSF) was designed to estimate oxygen fractions and further the trapped unburned fuel. As a comparison, Kalman filter (KF) and linear matrix inequality (LMI) based linear parameter-varying (LPV) filter were also applied. Robustness properties of the three observers are analyzed based on the theory of input-to-state (ISS) stability. The proposed models and methods and theoretical analysis are validated and compared through a set of simulations in high-fidelity GT-Power environment. The simulation results match well with theoretical analysis that the SVSF has good properties of strong robustness (with a root mean square error (RMSE) of 0.24, comparing with 0.4 of LPV filter and 0.49 of KF, for the unburned fuel estimation).

An Experimental Research on the Effects of Negative Valve Overlap on Performance and Operating Range in a Homogeneous Charge Compression Ignition Engine With RON40 and RON60 Fuels

2020 ◽  
Vol 142 (5) ◽  
Author(s):  
Seyfi Polat ◽  
Hamit Solmaz ◽  
Ahmet Uyumaz ◽  
Alper Calam ◽  
Emre Yılmaz ◽  
...  
Keyword(s):  
Pressure Rise ◽  
Engine Performance ◽  
Maximum Pressure ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Operating Range ◽  
Hcci Combustion ◽  
Residual Gas ◽  
Negative Valve Overlap ◽  
Valve Overlap

Abstract In this study, the effects of negative valve overlap (NVO) on homogenous charge compression ignition (HCCI) combustion and engine performance were experimentally investigated. A four stroke, single cylinder, port injection HCCI engine was operated at −16 deg crank angle (CA), −8 deg CA, and +8 deg CA valve overlap values and different lambda values and engine speeds at wide open throttle. RON40 and RON60 were used as test fuels in view of combustion and performance characteristics in HCCI mode. The variations of indicated mean effective pressure (IMEP), residual gas, CA50, indicated thermal efficiency (ITE), indicated specific fuel consumption (ISFC), maximum pressure rise rate (MPRR) and ringing intensity (RI) were observed on HCCI combustion. The results showed that NVO caused to trap residual gases in the combustion chamber. Hot residual gases showed heating and dilution effect on HCCI combustion. Combustion was retarded with the presence of residual gas at −16 deg CA NVO. Test results showed that higher imep and maximum in-cylinder pressure were obtained with RON60 according to RON40. As expected, CA50 was obtained later with RON60 compared to RON40 due to more resistance of auto-ignition. RON60 residual gas prevented the rapid and sudden combustion due to higher heat capacity of charge mixture. RI decreased with the usage of RON60 compared to RON40. Significant decrease was seen on RI with RON60 especially at lower lambda values. It was seen that HCCI combustion can be controlled with NVO and operating range of HCCI engines can be extended.

Quantifying Cyclic Variability in a Multicylinder HCCI Engine With High Residuals

2012 ◽  
Vol 134 (11) ◽  
Author(s):  
Erik Hellström ◽  
Jacob Larimore ◽  
Anna Stefanopoulou ◽  
Jeff Sterniak ◽  
Li Jiang
Keyword(s):  
Single Cylinder ◽  
Cyclic Variability ◽  
Cycle Basis ◽  
Hcci Combustion ◽  
Single Cylinder Engine ◽  
Operating Limits ◽  
Unburned Fuel ◽  
The Individual ◽  
Negative Valve Overlap ◽  
Valve Overlap

Cyclic variability (CV) in lean homogeneous charge compression ignition (HCCI) combustion at the limits of operation is a known phenomenon, and this work aims at investigating the dominant effects for the cycle evolution at these conditions in a multicylinder engine. Experiments are performed in a four-cylinder engine at the operating limits at late phasing of lean HCCI operation with negative valve overlap (nvo). A combustion analysis method that estimates the unburned fuel mass on a per-cycle basis is applied on both main combustion and the nvo period revealing and quantifying the dominant effects for the cycle evolution at high CV. The interpretation of the results and comparisons with data from a single-cylinder engine indicate that, at high CV, the evolution of combustion phasing is dominated by low-order deterministic couplings similar to the single-cylinder behavior. Variations, such as air flow and wall temperature, between cylinders strongly influence the level of CV but the evolution of the combustion phasing is governed by the interactions between engine cycles of the individual cylinders.

Determination of Cycle Temperatures and Residual Gas Fraction for HCCI Negative Valve Overlap Operation

2010 ◽  
Vol 3 (1) ◽  
pp. 124-141 ◽  
Author(s):  
Russell P. Fitzgerald ◽  
Richard Steeper ◽  
Jordan Snyder ◽  
Ronald Hanson ◽  
Randy Hessel
Keyword(s):  
Residual Gas Fraction ◽  
Residual Gas ◽  
Negative Valve Overlap ◽  
Valve Overlap

Quantifying Cyclic Variability in a Multi-Cylinder HCCI Engine With High Residuals

2012 ◽  
Author(s):  
Erik Hellström ◽  
Jacob Larimore ◽  
Anna Stefanopoulou ◽  
Jeff Sterniak ◽  
Li Jiang
Keyword(s):  
Single Cylinder ◽  
Cyclic Variability ◽  
Cycle Basis ◽  
Hcci Combustion ◽  
Single Cylinder Engine ◽  
Operating Limits ◽  
Unburned Fuel ◽  
The Individual ◽  
Negative Valve Overlap ◽  
Valve Overlap

Cyclic variability (CV) in lean HCCI combustion at the limits of operation is a known phenomenon, and this work aims at investigating the dominant effects for the cycle evolution at these conditions in a multi-cylinder engine. Experiments are performed in a four-cylinder engine at the operating limits at late phasing of lean HCCI operation with negative valve overlap (nvo). A combustion analysis method that estimates the unburned fuel mass on a per-cycle basis is applied on both main combustion and the nvo period revealing and quantifying the dominant effects for the cycle evolution at high CV. The interpretation of the results and comparisons with data from a single-cylinder engine indicate that, at high CV, the evolution of combustion phasing is dominated by low-order deterministic couplings similar to the single-cylinder behavior. Variations, such as in air flow and wall temperature, between cylinders strongly influence the level of CV but the evolution of the combustion phasing is governed by the interactions between engine cycles of the individual cylinders.

Analysis of ion current signal during negative valve overlap of HCCI combustion with high compression ratio

2020 ◽  
pp. 146808742097289
Author(s):  
Maximilian Wick ◽  
Denghao Zhu ◽  
Jun Deng ◽  
Liguang Li ◽  
Jakob Andert
Keyword(s):  
Combustion Process ◽  
Pressure Sensors ◽  
Ion Current ◽  
Cylinder Pressure ◽  
Combustion Control ◽  
Current Signal ◽  
Hcci Combustion ◽  
High Compression ◽  
Negative Valve Overlap ◽  
Valve Overlap

Homogenous charge compression ignition (HCCI) combustion is a low temperature combustion process which combines high combustion efficiency with ultra-low [Formula: see text] raw emissions. Steep increases of the in-cylinder pressure and unstable combustion sequences at the limits of the operating range can damage the engine and limit the use of HCCI to part load operation. This can be done using closed loop combustion control based on combustion parameters like the indicated mean effective pressure and the combustion phasing. Since in-cylinder pressure sensors are expensive components and therefore not suitable for series application, ion current sensors can be used as an additional source of information about the combustion. Combustion analysis using methods similar to those used in pressure based measurements can be implemented using an online analysis of the ion current signal. In this study, the ion current sensor will be examined for its suitability for combustion control under HCCI conditions with lean air/fuel ratios and high compression ratios. Research has found that the ion current signal is strongly depended on the boundary conditions. Especially the air/fuel ratio which plays an important role for signal strength during the combustion process. When using valve timings with negative valve overlap in combination with a fuel pre-injection, a further peak of the ion current signal close to the gas exchange top dead center can be found in addition to the one during combustion. At the same time, it is hard to extract information from the cylinder pressure signal during NVO. Under lean conditions this peak even exceeds the signal during combustion. This study analyzes the ion current signal during NVO and its potential to be used for future combustion control concepts. The ion current signal shows potential to stabilize HCCI combustion at high loads. However, the prediction of late combustion cycles is still challenging.

Evaluation of Unburned Fuel in the Modeling of the Combustion Process in a 360 MW Coal-Fired Boiler

2020 ◽  
Author(s):  
Eduardo Dias ◽  
Conrado Ermel ◽  
Paulo Rodolfo Buffon Ortiz ◽  
Paulo Smith Schneider
Keyword(s):  
Combustion Process ◽  
Unburned Fuel

Extraction and Determination of Physico-chemical Properties of Oil from Watermelon Seeds (Citrullus lanatus L) to Use in Internal Combustion Engines

2017 ◽  
Vol 68 (11) ◽  
pp. 2676-2681
Author(s):  
Mihaela Gabriela Dumitru ◽  
Dragos Tutunea
Keyword(s):  
Fatty Acid ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Citrullus Lanatus ◽  
Combustion Process ◽  
Chemical Properties ◽  
Physico Chemical ◽  
Mean Diameter ◽  
Geometrical Mean ◽  
Reduction Of Nox

The purpose of this work was to investigate the physicochemical properties of watermelon seeds and oil and to find out if this oil is suitable and compatible with diesel engines. The results showed that the watermelon seeds had the maximum length (9.08 mm), width (5.71mm), thickness (2.0 mm), arithmetic mean diameter (5.59 mm), geometrical mean diameter (4.69 mm), sphericity (51.6%), surface area (69.07), volume 0.17 cm3 and moisture content 5.4%. The oil was liquid at room temperature, with a density and refractive index of 0.945 and 1.4731 respectively acidity value (1.9 mgNaOH/g), free fatty acid (0.95 mgNaOH), iodine value (120 mgI2/100g), saponification value (180 mgKOH/g), antiradical activity (46%), peroxide value (7.5 mEqO2/Kg), induction period (6.2 h), fatty acid: palmitic acid (13.1%), stearic acid (9.5 %), oleic acid (15.2 %) and linoleic acid (61.3%). Straight non food vegetable oils can offer a solution to fossil fuels by a cleaner burning with minimal adaptation of the engine. A single cylinder air cooled diesel engine Ruggerini RY 50 was used to measure emissions of various blends of watermelon oil (WO) and diesel fuel (WO10D90, WO20D80, WO30D70 and WO75D25). The physic-chemical properties of the oil influence the combustion process and emissions leading to the reduction of NOX and the increase in CO, CO2 and HC.

scholarly journals Comparison of Diesel Engine Vibroacoustic Properties Powered by Bio and Standard Fuel

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1478
Author(s):  
Radoslaw Wrobel ◽  
Gustaw Sierzputowski ◽  
Zbigniew Sroka ◽  
Radostin Dimitrov
Keyword(s):  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Combustion Process ◽  
Significant Other ◽  
Engine Torque ◽  
Engine Model ◽  
Vehicle Operation ◽  
History Of ◽  
Profile Changes ◽  
The Time Domain

Alternative fuels appeared soon after the first internal combustion engines were designed. The history of alternative fuels is basically as long as the history of the automotive industry. Initially, fuels whose physicochemical properties allowed for a change in parameters of the combustion process in order to achieve greater efficiency and reliability were searched for. Nowadays, there are significantly more variables; in addition to the above mentioned parameters, alternative fuels are being sought that will ensure environmental protection during vehicle operation and improve the ergonomics of use. This article outlines the results of the authors’ own comparative tests of vibrations of a vibroacoustic character. Based on a popular engine model, the vibration–acoustic responses of a system powered by two types of fuel, namely, diesel and biodiesel (B10), are compared. The research consists of comparing vibrations in both time and frequency domains. In the case of the time domain, the evaluation was performed with vibrations as a function of engine torque and speed. In the case of frequency analysis, the focus was on changes in the frequency response for the tested fuels. The research shows that the profile of vibroacoustic vibrations changes in the case of biodiesel power supply in relation to standard fuel. The vibration profile changes significantly as a function of speed and only slightly in relation to the engine load. The results presented in this article show different vibroacoustic responses of an engine powered by diesel and biodiesel; the change is minor for lower speeds but significant (other harmonics are dominant) for higher speeds (changes in the dominant harmonic magnitude of up to 10% at a crankshaft speed of 3000 rpm).

scholarly journals Combustion Thermodynamics of Ethanol, n-Heptane, and n-Butanol in a Rapid Compression Machine with a Dual Direct Injection (DDI) Supply System

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2729
Author(s):  
Ireneusz Pielecha ◽  
Sławomir Wierzbicki ◽  
Maciej Sidorowicz ◽  
Dariusz Pietras
Keyword(s):  
Heat Release ◽  
Combustion Chamber ◽  
Internal Combustion Engines ◽  
Direct Injection ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Injection System ◽  
Rapid Compression Machine ◽  
Process Indicators ◽  
Rapid Compression

The development of internal combustion engines involves various new solutions, one of which is the use of dual-fuel systems. The diversity of technological solutions being developed determines the efficiency of such systems, as well as the possibility of reducing the emission of carbon dioxide and exhaust components into the atmosphere. An innovative double direct injection system was used as a method for forming a mixture in the combustion chamber. The tests were carried out with the use of gasoline, ethanol, n-heptane, and n-butanol during combustion in a model test engine—the rapid compression machine (RCM). The analyzed combustion process indicators included the cylinder pressure, pressure increase rate, heat release rate, and heat release value. Optical tests of the combustion process made it possible to analyze the flame development in the observed area of the combustion chamber. The conducted research and analyses resulted in the observation that it is possible to control the excess air ratio in the direct vicinity of the spark plug just before ignition. Such possibilities occur as a result of the properties of the injected fuels, which include different amounts of air required for their stoichiometric combustion. The studies of the combustion process have shown that the combustible mixtures consisting of gasoline with another fuel are characterized by greater combustion efficiency than the mixtures composed of only a single fuel type, and that the influence of the type of fuel used is significant for the combustion process and its indicator values.

Sign in / Sign up

Export Citation Format

Share Document