scholarly journals Comparison of Diesel Engine Vibroacoustic Properties Powered by Bio and Standard Fuel

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1478
Author(s):  
Radoslaw Wrobel ◽  
Gustaw Sierzputowski ◽  
Zbigniew Sroka ◽  
Radostin Dimitrov
Keyword(s):  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Combustion Process ◽  
Significant Other ◽  
Engine Torque ◽  
Engine Model ◽  
Vehicle Operation ◽  
History Of ◽  
Profile Changes ◽  
The Time Domain

Alternative fuels appeared soon after the first internal combustion engines were designed. The history of alternative fuels is basically as long as the history of the automotive industry. Initially, fuels whose physicochemical properties allowed for a change in parameters of the combustion process in order to achieve greater efficiency and reliability were searched for. Nowadays, there are significantly more variables; in addition to the above mentioned parameters, alternative fuels are being sought that will ensure environmental protection during vehicle operation and improve the ergonomics of use. This article outlines the results of the authors’ own comparative tests of vibrations of a vibroacoustic character. Based on a popular engine model, the vibration–acoustic responses of a system powered by two types of fuel, namely, diesel and biodiesel (B10), are compared. The research consists of comparing vibrations in both time and frequency domains. In the case of the time domain, the evaluation was performed with vibrations as a function of engine torque and speed. In the case of frequency analysis, the focus was on changes in the frequency response for the tested fuels. The research shows that the profile of vibroacoustic vibrations changes in the case of biodiesel power supply in relation to standard fuel. The vibration profile changes significantly as a function of speed and only slightly in relation to the engine load. The results presented in this article show different vibroacoustic responses of an engine powered by diesel and biodiesel; the change is minor for lower speeds but significant (other harmonics are dominant) for higher speeds (changes in the dominant harmonic magnitude of up to 10% at a crankshaft speed of 3000 rpm).

A comparative study of the effect of compression ratio on the efficiency and flame development angle in a Cooperative Fuel Research engine fueled with binary gasoline–alcohol blends

2019 ◽  
pp. 146808741985910 ◽  
Author(s):  
Guillermo Rubio-Gómez ◽  
Lis Corral-Gómez ◽  
David Rodriguez-Rosa ◽  
Fausto A Sánchez-Cruz ◽  
Simón Martínez-Martínez
Keyword(s):  
Comparative Study ◽  
Compression Ratio ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Combustion Process ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Flame Development ◽  
The Impact

In the last few years, increasing concern about the harmful effects of the use of fossil fuels in internal combustion engines has been observed. In addition, the limited availability of crude oil has driven the interest in alternative fuels, especially biofuels. In the context of spark ignition engines, bioalcohols are of great interest owing to their similarities and blend capacities with gasoline. Methanol and ethanol have been widely used, mainly due to their knocking resistance. Another alcohol of great interest is butanol, thanks to its potential of being produced as biofuel and its heat value closer to gasoline. In this study, a comparative study of gasoline–alcohol blend combustion, with up to 20% volume, with neat gasoline has been carried out. A single-cylinder, variable compression ratio, Cooperative Fuel Research-type spark ignition engine has been employed. The comparison is made in terms of fuel conversion efficiency and flame development angle. Relevant information related to the impact in the combustion process of the use of the three main alcohols used in blends with gasoline has been obtained.

scholarly journals Energetic Analysis of the Aircraft Diesel Engine

2019 ◽  
Vol 252 ◽  
pp. 05012
Author(s):  
Łukasz Grabowski ◽  
Konrad Pietrykowski ◽  
Paweł Karpiński
Keyword(s):  
Steady State ◽  
Diesel Engine ◽  
Energy Balance ◽  
Internal Combustion Engines ◽  
Combustion Process ◽  
Energy Losses ◽  
Exhaust Gas ◽  
Combustion Engines ◽  
Engine Model ◽  
Energetic Analysis

The analysis of the distribution of thermal energy generated during the combustion process in internal combustion engines and the estimation of individual losses are important regarding performance and efficiency. The article analyses the energy balance of the designed two-stroke opposed piston diesel engines with offset, i.e. the angle by which the crankshaft at the side of exhaust ports is ahead of the crankshaft at the side of intake ports. Based on the developed zero-dimensional engine model, a series of simulations were performed in steady-state conditions using the AVL BOOST software. The values of individual energy losses, including cooling losses, exhaust gas losses, friction losses were obtained. The influence of decreasing and increasing the offset on the performance of the tested engine was analysed.

The study of a tractor diesel engine operation on ethanol and rapeseed oil at various speed modes

Trudy NAMI ◽  
2022 ◽  
pp. 53-59
Author(s):  
A. N. Kozlov ◽  
M. I. Araslanov
Keyword(s):  
Diesel Engine ◽  
Rapeseed Oil ◽  
Power Plants ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Renewable Energy Sources ◽  
Comparative Method ◽  
Combustion Process ◽  
Engine Operation ◽  
Tractor Diesel

Introduction (problem statement and relevance). The depletion of oil fuels reserves and the steady growth of their consumption will require new solutions in the development of technologies based on renewable energy sources. The study of the possible alternative fuels use in internal combustion engines is a complex scientific task, including the research of the alternative fuels effect on the power plants operation efficiency.The purpose of the study was to obtain the speed characteristics of a diesel engine operating on ethyl alcohol and rapeseed oil.Methodology and research methods. An air-cooled with volumetric mixture formation tractor diesel engine of dimension 2Ch 10.5/12.0 was selected as an object of research. The study was carried out by a comparative method. To measure the speed characteristic a fixed cyclic fuel supply was applied after the engine reaching the nominal operating mode at a crankshaft speed of 1800 min-1 and an average effective pressure in the cylinder of 0.588 MPa. This approach, with the all-mode regulator of the fuel pump turned off, made it possible to identify the main regularities of intra-cylinder processes at different speed modes of engine operation.Scientific novelty and results. The article presents the bench tests results of a diesel engine operating at various speed modes on ethanol and rapeseed oil, and analyzes in detail the main indicators of the combustion process and the effective engine performance in comparison to the use of traditional fuel. The practical significance lies in the possibility of using the obtained results to improve the diesel engines operation on alternative renewable fuels.

scholarly journals Investigating Combustion Process of N-Butanol-Diesel Blends in a Diesel Engine with Variable Compression Ratio

2021 ◽  
Vol 3 (3) ◽  
pp. 618-628
Author(s):  
György Szabados ◽  
Kristóf Lukács ◽  
Ákos Bereczky
Keyword(s):  
Heat Release ◽  
Heat Release Rate ◽  
Compression Ratio ◽  
Release Rate ◽  
Ignition Delay ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Combustion Process ◽  
Injection Angle ◽  
Combustion Properties

The search for alternative fuels for internal combustion engines is ongoing. Among the alternatives, plant-based fuels can also be mentioned. Alcohol is not a common fuel for diesel engines because the physical and chemical properties of the alcohols are closer to those of gasoline. In our research, the combustion properties of diesel-n-butanol mixtures have been investigated to obtain results on the effect of butanol blending on combustion. Among the combustion properties, ignition delay, in-cylinder pressure, and heat release rate can be mentioned. They have been observed under different compression conditions on an engine on which the compression ratio can be adjusted. The method used was a quite simple one, so the speed of the engine was set to a constant 900 rpm without load, while three compression ratios (19.92, 15.27, and 12.53) were adjusted with a fuel flow rate of 13 mL/min and the pre-injection angle of 18° BTDC. Blending butanol into the investigated fuel does not significantly affect maximal values of indicated pressure, while much more effect on the pressure rising rate can be detected. Furthermore, heat release rate and ignition delay increased at every compression ratio investigated. Despite the low blending rates of butanol in the mixtures, butanol significantly affects the combustion parameters, especially at high compression ratios.

Simulation of Turbocharged Marine Diesel Engine for Electrical Power System Trainer

2012 ◽  
Author(s):  
Matthew Boley ◽  
Christopher L. Hagen
Keyword(s):  
Power System ◽  
Internal Combustion Engines ◽  
Direct Injection ◽  
Electrical Power ◽  
Combustion Process ◽  
Mean Value ◽  
Combustion Model ◽  
Electrical Power System ◽  
Training Simulator ◽  
Engine Model

This paper presents an application of the mean value combustion model to simulate large bore turbocharged diesel engines, coupled with large electric AC synchronous generators, to mimic power generation within a training simulator for a ship board electrical power system. A mean value engine model has been developed to simulate the most prevalent phenomena occurring in diesel direct injection internal combustion engines. The combustion process is modeled as a mean value system where characteristics of combustion are averaged over the entire cycle. Detailed models of the air intake, fuel delivery, and internal/external cooling systems have been developed using concepts from fluid dynamics and thermodynamics. The engine model has been created in MATLAB® Simulink® to simulate actual hardware signals sent to the power management controller to facilitate the development of the power system trainer. The model has been structured so that it is highly adaptable and is capable of simulating a wide variety of engine bore sizes and cylinder numbers which has significantly increased the utility of the work presented herein.

scholarly journals The study of the spark ignition engine operation at fuelling with n-butanol-gasoline blends

2020 ◽  
Vol 180 ◽  
pp. 01010
Author(s):  
Cristian Sandu ◽  
Constantin Pană ◽  
Niculae Negurescu ◽  
Alexandru Cernat ◽  
Cristian Nuţu ◽  
...  
Keyword(s):  
Oxygen Content ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Combustion Process ◽  
Good Alternative ◽  
Spark Ignition ◽  
Spark Ignition Engine ◽  
Engine Operation ◽  
High Oxygen Content ◽  
Combustion Properties

For conventional internal combustion engines alternative fuels such alcohols (ethanol, methanol and butanol) have attracted more attention. This aspect is due to the fact that alcohols have good combustion properties and high oxygen content. Butanol is a viable fuel for blending with conventional fuels such as gasoline or diesel because of its high miscibility with these conventional fuels. The high combustion speed of butanol compared to that of gasoline ensures a shorter burning process thus the engine thermal efficiency can potentially be improved. Moreover, the additional oxygen content of the alcohol n-butanol can potentially improve the combustion process and can lead to a reduction of carbon monoxide and unburnt hydrocarbons emissions level. Utilizing butanol-gasoline blends can provide a good solution for the reduction of greenhouse gases level (CO2) and pollutants level (CO, HC, and NOx). An experimental study was carried out in a spark ignition engine which was fueled with a blend of n-butanol-gasoline at different volume percentages. The objective of this paper is to determine the effects of butanol on the engine energetic performances and on the emissions (HC, CO and NOx). At first the engine fueled with pure gasoline to set up a reference at the engine load χ=55%, engine speed of n=2500 min-1 and different excess air coefficients (λ). After setting the reference the engine was fueled with butanol-gasoline blend (10% vol. butanol 90% vol. gasoline) with the same engine adjustments. At butanol use the CO, HC and CO2 emissions level decreased, but the NOx emission level increased. The butanol can be considered a good alternative fuel for the spark ignition engines without modifications.

scholarly journals Influence of biofuels usage in internal combustion engines of agricultural tractors on output parametrs

2010 ◽  
Vol 58 (2) ◽  
pp. 219-228
Author(s):  
Tomáš Šmerda ◽  
Jiří Čupera
Keyword(s):  
Internal Combustion Engine ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Combustion Engine ◽  
Combustion Process ◽  
Internal Combustion ◽  
Environmental Benefits ◽  
Injection System ◽  
Renewable Energy Resources ◽  
Agricultural Tractors

Application of alternative fuels brings the social benefits in terms of reducing dependence on oil industry and its products as well as decreasing of damage of the environment together with using of na­tu­ral resources, especially in field of renewable energy resources. The use of biofuels is the most important part of energy strategy in European Union, whose member states have agreed the content of biofuels will achieve 5.75% of the total energy sum of fuel for transport purposes in 2010. Operation of internal combustion engine fueled by RME brings environmental benefits as described several authors in analysis of the life cycle. The contribution deals with technical difficulties of the RME usage in internal combustion engine used in agricultural tractors. Different fuel causes different process of combustion which means changes in output power and pollution. The aim of this experiment was to determine these effects. Experimental work was divided into two parts according to various fuel systems. The first tractor was equipped with mechanical injection system, the second one was provided with common-rail fuel system. The test procedures consisted of measurement of power- torque curves where the engine load was created by Eddy current dynamometer. Exhaust gas analyzer sampled the pollution of carbon monoxide, carbon dioxide and hydrocarbons as the most important indicators of combustion process.

scholarly journals Investigations for a Trajectory Variation to Improve the Energy Conversion for a Four-Stroke Free-Piston Engine

2021 ◽  
Vol 11 (13) ◽  
pp. 5981
Author(s):  
Robin Tempelhagen ◽  
Andreas Gerlach ◽  
Sebastian Benecke ◽  
Kevin Klepatz ◽  
Roberto Leidhold ◽  
...  
Keyword(s):  
Degrees Of Freedom ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Combustion Process ◽  
Optimal Operation ◽  
Combustion Engines ◽  
Piston Engine ◽  
Free Piston ◽  
Free Piston Engine ◽  
Future Work

Internal combustion engines with a crankshaft have been successfully developed for many years. They are lacking in the fact that the piston trajectory, i.e., position as a function of time, is limited by the crankshaft motion law. Position-controlled electric linear machines directly coupled to the piston allow to realize free-piston engines. Unlike the crankshaft-based engines, they allow for a higher degree of freedom in shaping the piston trajectory, including adaptive compression ratios, which enables optimal operation with alternative fuels. The possibility of adapting the stroke course results in new degrees of freedom with which the combustion process can be optimized. In this work, four-stroke trajectories with different amplitudes and piston dynamics have been proposed and analyzed regarding efficiency. A simulation model was created based on experimental measurements for testing the proposed trajectories. It could be proved that the variation of the trajectory resulted in an improvement of the overall efficiency. The trajectories were described analytically so that they can be used for a prototype in a future work.

Extraction and Determination of Physico-chemical Properties of Oil from Watermelon Seeds (Citrullus lanatus L) to Use in Internal Combustion Engines

2017 ◽  
Vol 68 (11) ◽  
pp. 2676-2681
Author(s):  
Mihaela Gabriela Dumitru ◽  
Dragos Tutunea
Keyword(s):  
Fatty Acid ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Citrullus Lanatus ◽  
Combustion Process ◽  
Chemical Properties ◽  
Physico Chemical ◽  
Mean Diameter ◽  
Geometrical Mean ◽  
Reduction Of Nox

The purpose of this work was to investigate the physicochemical properties of watermelon seeds and oil and to find out if this oil is suitable and compatible with diesel engines. The results showed that the watermelon seeds had the maximum length (9.08 mm), width (5.71mm), thickness (2.0 mm), arithmetic mean diameter (5.59 mm), geometrical mean diameter (4.69 mm), sphericity (51.6%), surface area (69.07), volume 0.17 cm3 and moisture content 5.4%. The oil was liquid at room temperature, with a density and refractive index of 0.945 and 1.4731 respectively acidity value (1.9 mgNaOH/g), free fatty acid (0.95 mgNaOH), iodine value (120 mgI2/100g), saponification value (180 mgKOH/g), antiradical activity (46%), peroxide value (7.5 mEqO2/Kg), induction period (6.2 h), fatty acid: palmitic acid (13.1%), stearic acid (9.5 %), oleic acid (15.2 %) and linoleic acid (61.3%). Straight non food vegetable oils can offer a solution to fossil fuels by a cleaner burning with minimal adaptation of the engine. A single cylinder air cooled diesel engine Ruggerini RY 50 was used to measure emissions of various blends of watermelon oil (WO) and diesel fuel (WO10D90, WO20D80, WO30D70 and WO75D25). The physic-chemical properties of the oil influence the combustion process and emissions leading to the reduction of NOX and the increase in CO, CO2 and HC.

scholarly journals Combustion Thermodynamics of Ethanol, n-Heptane, and n-Butanol in a Rapid Compression Machine with a Dual Direct Injection (DDI) Supply System

Energies ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2729
Author(s):  
Ireneusz Pielecha ◽  
Sławomir Wierzbicki ◽  
Maciej Sidorowicz ◽  
Dariusz Pietras
Keyword(s):  
Heat Release ◽  
Combustion Chamber ◽  
Internal Combustion Engines ◽  
Direct Injection ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Injection System ◽  
Rapid Compression Machine ◽  
Process Indicators ◽  
Rapid Compression

The development of internal combustion engines involves various new solutions, one of which is the use of dual-fuel systems. The diversity of technological solutions being developed determines the efficiency of such systems, as well as the possibility of reducing the emission of carbon dioxide and exhaust components into the atmosphere. An innovative double direct injection system was used as a method for forming a mixture in the combustion chamber. The tests were carried out with the use of gasoline, ethanol, n-heptane, and n-butanol during combustion in a model test engine—the rapid compression machine (RCM). The analyzed combustion process indicators included the cylinder pressure, pressure increase rate, heat release rate, and heat release value. Optical tests of the combustion process made it possible to analyze the flame development in the observed area of the combustion chamber. The conducted research and analyses resulted in the observation that it is possible to control the excess air ratio in the direct vicinity of the spark plug just before ignition. Such possibilities occur as a result of the properties of the injected fuels, which include different amounts of air required for their stoichiometric combustion. The studies of the combustion process have shown that the combustible mixtures consisting of gasoline with another fuel are characterized by greater combustion efficiency than the mixtures composed of only a single fuel type, and that the influence of the type of fuel used is significant for the combustion process and its indicator values.

Sign in / Sign up

Export Citation Format

Share Document