Mechanism of Fast Transition of Pressure Pulsations in the Vaneless Space of a Model Pump-Turbine During Runaway

2019 ◽  
Vol 141 (12) ◽  
Author(s):  
Xiaoxi Zhang ◽  
Wei Zeng ◽  
Yongguang Cheng ◽  
Zhiyan Yang ◽  
Qiuhua Chen ◽  
...  
Keyword(s):  
Transient Flow ◽  
Characteristic Curve ◽  
Three Dimensional ◽  
Low Frequency ◽  
Vortex Structures ◽  
Pressure Pulsations ◽  
Pump Turbine ◽  
Whole Process ◽  
Time Variations ◽  
Flow Vortex

The pressure pulsations in the vaneless space of pump-turbines are extremely intense and always experience rapid time variations during transient scenarios, causing structural vibrations and even more serious accidents. In this study, the mechanism behind the rapid time variations of the vaneless space pressure pulsations in a model pump-turbine during runaway was analyzed through three-dimensional (3D) numerical simulations. These results show that the high-frequency pressure pulsation components originating from rotor–stator interactions (RSI) are dominant during the whole process. These components fluctuate significantly in frequency when the working point goes through the S-shaped region of the characteristic curve, with the amplitudes increasing. Meanwhile, some low-frequency pulsations are also enhanced and become obvious. These features can be attributed to the transitions of the inter blade vortex structures (IBVSs) to the forward flow vortex structures (FFVSs) and the back flow vortex structures (BFVSs) at the impeller entrance, when the pump-turbine operates in the region with S-shaped characteristics. The FFVSs mainly cause decreases in frequency and introduce low-frequency pulsations, while the BFVSs are responsible for the unstable fluctuations. These findings contribute to the understanding of how transient flow patterns evolve and may provide new ideas about avoiding severe pressure pulsations caused by rotating stalls in the pump-turbine during transient scenarios.

scholarly journals Simulation and Experimental Investigation of the Stay Vane Channel Flow in a Reversible Pump Turbine at Off-Design Conditions

2017 ◽  
Vol 61 (2) ◽  
pp. 94 ◽  
Author(s):  
Sandro Erne ◽  
Gernot Edinger ◽  
Anton Maly ◽  
Christian Bauer
Keyword(s):  
Transient Flow ◽  
Guide Vane ◽  
Low Frequency ◽  
Rotating Stall ◽  
Design Flow ◽  
Flow State ◽  
Mean Flow ◽  
Load Range ◽  
Pump Turbine ◽  
Stall Inception

This work presents the assessment of the mean flow field and low frequency disturbances in the stay vane channel of a model pump turbine using transient numerical simulations and LDV-based measurements. The focus is laid on transient CFD simulations of characteristic flow states in the stay vane channel when operating at off-design conditions in pump mode. Experimental and numerical investigations obtained a shifting velocity distribution between the shroud and hub of the distributor when continuously increasing the discharge in the part-load range. Simulations captured the occurrence of this changing flow state in the stay vane channel reasonably well. A further increase of the discharge showed a uniformly redistributed mean flow of both hub and shroud side. Monitoring points and integral quantities from measurements and transient simulations were used to interpret the development of transient flow patterns in the stay vane channel at the operating point of strongest asymmetrical flow. During simulation and measurement, a dominant rotating stall inception was observed near the design flow of the pump turbine. At this point where the stall becomes severe, a high level of correlation between the signals of the upper and lower stalled flow in the stay vane channel was calculated. Further simulations for different guide vane positions predicted a strong influence of the guide vane position on the structure of rotating stall.

Looping Dynamic Characteristics of a Pump-Turbine in the S-shaped Region During Runaway

2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Xiaoxi Zhang ◽  
Yongguang Cheng ◽  
Linsheng Xia ◽  
Jiandong Yang ◽  
Zhongdong Qian
Keyword(s):  
Dynamic Characteristics ◽  
Transient Flow ◽  
Three Dimensional ◽  
Flow Patterns ◽  
Operating Conditions ◽  
Static Characteristics ◽  
Pump Turbine ◽  
Transient Flows ◽  
Characteristics Method ◽  
Water Conveyance

During transients, hydroturbines may demonstrate some dynamic characteristics that differ from the corresponding static characteristics in steady operating conditions. To study the dynamic characteristics of a pump-turbine, we simulated the runaway transients in a model pumped-storage plant by coupling one-dimensional (1D) water conveyance system and three-dimensional (3D) pump-turbine. The results show that the runaway dynamic trajectories form loops in the S-shaped region in the unit discharge and unit torque charts of the pump-turbine, not following the corresponding static characteristics. Theoretical analysis and flow patterns comparisons illustrate that the looping trajectories are mainly caused by the successive features of transient flow patterns, namely, the transient flows in the pump-turbine are influenced by their previous status. These features induce different performances between similar dynamic operating points in different moving directions. Furthermore, through comparing the transient parameters calculated by the dynamic and static characteristics separately, we found that both methods are available to capture the unstable behaviors of the pump-turbine, but the dynamic method displays more accurate results when simulating the critical transient parameters. Therefore, in practical engineering applications, we suggest to use the static characteristics method for stability analysis while dynamic characteristics method for transient parameters, which is important for optimizing the layout of water conveyance systems.

scholarly journals Research on Groove Method to Suppress Stall in Pump Turbine

Energies ◽  
2020 ◽  
Vol 13 (15) ◽  
pp. 3822
Author(s):  
Yong Liu ◽  
Hongjuan Ran ◽  
Dezhong Wang
Keyword(s):  
Characteristic Curve ◽  
Low Frequency ◽  
Pulse Amplitude ◽  
Optimization Method ◽  
High Amplitude ◽  
Pump Turbine ◽  
Structure Flow ◽  
Hydrodynamic Optimization ◽  
Full Consideration ◽  
Pressure Pulse Amplitude

The pump turbine is prone to stall when running at part-load operation. Stalls would cause a hump-like head characteristic curve, low-frequency high-amplitude pressure pulsation, and surge or resonance in the system. There is a lack of efficient methods for pump turbine stall suppression. The traditional blade hydrodynamic optimization method has limited effect and would influence the other characteristics. As the essence of stall is flow separation, forming a severe backflow vortex, a “Groove Method” is put forward and employed to suppress stall in a pump turbine with the full consideration of the mechanical structure, flow field, and pressure field. Both experiments and calculations are carried out to test the effectiveness of this new method. Furthermore, its deep mechanisms are revealed. This method can weaken the head hump to a certain extent and reduce the pressure pulse amplitude induced by stall. Meanwhile, the performance at the design operating point is not disturbed much.

scholarly journals Three-Dimensional Local MHD Simulations of High States and Low States in Magnetic Accretion Disks

1998 ◽  
Vol 188 ◽  
pp. 400-401
Author(s):  
T. Matsuzaki ◽  
R. Matsumoto ◽  
T. Tajima ◽  
K. Shibata
Keyword(s):  
Accretion Disks ◽  
Magnetic Energy ◽  
Three Dimensional ◽  
Low Frequency ◽  
High State ◽  
Mhd Simulations ◽  
Soft State ◽  
Hard State ◽  
Time Variations ◽  
Magnetic Energy Release

Black hole candidates sometimes show a transition between the high (or soft) state and the low (or hard) state. In the low state, low frequency time variations are much larger than the high state. A possible mechanism of the large-amplitude, sporadic time variabilities in the low-state is the magnetic energy release in low-β (β = Pgas/Pmag < 1) disks (Mineshige, Kusunose & Matsumoto 1995). It had been thought that low-β disks cannot exist because buoyant escape of magnetic flux due to the Parker instability may set the lower limit for β inside the disk. Shibata, Tajima & Matsumoto (1990), however, pointed out that in accretion disks, once a low-β disk is formed, it can stay in low-β state partly because the growth rate of the Parker instability decreases when β < 1. They suggested that magnetic accretion disks fall into two types; high-β disks and low-β disks.

scholarly journals Evolution of a narrow-band spectrum of random surface gravity waves

2003 ◽  
Vol 478 ◽  
pp. 1-10 ◽  
Author(s):  
KRISTIAN B. DYSTHE ◽  
KARSTEN TRULSEN ◽  
HARALD E. KROGSTAD ◽  
HERVÉ SOCQUET-JUGLARD
Keyword(s):  
Three Dimensional ◽  
Low Frequency ◽  
Three Dimensions ◽  
Band Spectrum ◽  
Nls Equation ◽  
Random Surface ◽  
Narrow Bandwidth ◽  
Quasi Stationary State ◽  
The Stability ◽  
Three Dimensional Simulations

Numerical simulations of the evolution of gravity wave spectra of fairly narrow bandwidth have been performed both for two and three dimensions. Simulations using the nonlinear Schrödinger (NLS) equation approximately verify the stability criteria of Alber (1978) in the two-dimensional but not in the three-dimensional case. Using a modified NLS equation (Trulsen et al. 2000) the spectra ‘relax’ towards a quasi-stationary state on a timescale (ε2ω0)−1. In this state the low-frequency face is steepened and the spectral peak is downshifted. The three-dimensional simulations show a power-law behaviour ω−4 on the high-frequency side of the (angularly integrated) spectrum.

scholarly journals Validation of the Portuguese version of Amsterdam Preoperative Anxiety and Information Scale (APAIS)

2021 ◽  
Vol 19 (1) ◽  
Author(s):  
Sandra Maurício ◽  
Isabel Rebêlo ◽  
Catarina Madeira ◽  
Filipa Resende ◽  
Susana Esteves
Keyword(s):  
Anesthetic Management ◽  
Characteristic Curve ◽  
Three Dimensional ◽  
Psychometric Evaluation ◽  
Preoperative Anxiety ◽  
Youden Index ◽  
Three Dimensional Model ◽  
Portuguese Version ◽  
Information Scale ◽  
Oncology Centre

Abstract Background Preoperative anxiety is common among the oncological surgical population. Due to its psychological and physiological detrimental effects, identifying and addressing it is of uttermost importance to improve anesthetic management and patient’s outcomes. The aim of this study is to validate the Portuguese version of Amsterdam Preoperative Anxiety and Information Scale (APAIS) in the oncological population. Methods Following forward and backward translation of the original APAIS scale, further adaptation was obtained through cognitive interviewing. The resulting instrument was tested on the day before surgery on a sample of adult cancer surgical patients from a Portuguese oncology centre. Psychometric evaluation was derived from inter-item correlation, confirmatory factor analysis, Cronbach’s alpha, correlation with comparative scales, receiver operating characteristic curve and Youden index. Results 109 patients (58 males, 51 females) were included. A three-dimensional model—anxiety about anesthesia, anxiety about surgery and desire for information, showed the best fit to the data. The questionnaire revealed high internal consistency (Cronbach alpha 0.81) and good inter-item correlation. Also, Portuguese APAIS correlated well with the gold standard anxiety scale. Therefore, the psychometric properties of this scale version make it a valid and reliable instrument. The optimal cutoff to maximize both sensitivity and specificity was 12 for the APAIS global anxiety score. Conclusions Portuguese APAIS version is an accurate tool to identify preoperative anxiety among cancer patients and might impact its management, from premedication choice to provision of information and reassurance about either anesthesia or surgery.

Obstacle drag in stratified flow

1990 ◽  
Vol 429 (1876) ◽  
pp. 119-140 ◽  
Keyword(s):  
Experimental Study ◽  
Linear Density ◽  
Three Dimensional ◽  
Inviscid Flow ◽  
Force Balance ◽  
Video Recordings ◽  
Lee Waves ◽  
Time Variations ◽  
Obstacle Height ◽  
Stable Linear

This paper describes an experimental study of the drag of two- and three-dimensional bluff obstacles of various cross-stream shapes when towed through a fluid having a stable, linear density gradient with Brunt-Vaisala frequency, N . Drag measurements were made directly using a force balance, and effects of obstacle blockage ( h / D , where h and D are the obstacle height and the fluid depth, respectively) and Reynolds number were effectively eliminated. It is shown that even in cases where the downstream lee waves and propagating columnar waves are of large amplitude, the variation of drag with the parameter K ( = ND /π U ) is qualitatively close to that implied by linear theories, with drag minima existing at integral values of K . Under certain conditions large, steady, periodic variations in drag occur. Simultaneous drag measurements and video recordings of the wakes show that this unsteadiness is linked directly with time-variations in the lee and columnar wave amplitudes. It is argued that there are, therefore, situations where the inviscid flow is always unsteady even for large times; the consequent implications for atmospheric motions are discussed.

scholarly journals Pressure Analysis in the Draft Tube of a Pump-Turbine under Steady and Transient Conditions

Energies ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4732
Author(s):  
Jing Yang ◽  
Yue Lv ◽  
Dianhai Liu ◽  
Zhengwei Wang
Keyword(s):  
Steady State ◽  
Pressure Pulsation ◽  
Transient Flow ◽  
Draft Tube ◽  
Simulation Method ◽  
Wall Pressure ◽  
Pump Turbine ◽  
Steady State Condition ◽  
Transient Conditions ◽  
Pumped Storage

Pumped-storage power stations play a regulatory role in the power grid through frequent transition processes. The pressure pulsation in the draft tube of the pump-turbine under transient processes is important for safe operation, which is more intense than that in the steady-state condition. However, there is no effective method to obtain the exact pressure in the draft tube in the transient flow field. In this paper, the pressure in the draft tube of a pump-turbine under steady-state and transient conditions are studied by means of CFD. The reliability of the simulation method is verified by comparing the real pressure pulsation data with the test results. Due to the distribution of the pressure pulsation in the draft tube being complex and uneven, the location of the pressure monitoring points directly affects the accurate judgement of cavitation. Eight monitoring surfaces were set in the straight cone of the draft tube and nine monitoring points were set on each monitoring surface to analyze the pressure differences on the wall and inside the center of the draft tube. The relationships between the pressure pulsation value inside the center of the draft tube and on the wall are studied. The “critical” wall pressure pulsation value when cavitation occurs is obtained. This study provides references for judging cavitation occurrences by using the wall pressure pulsation value in practical engineering.

The Investigation of the Optimization Scheme of the Low-cycle Fatigue Cropping Based on the Acoustic Emission Technique

2021 ◽  
Author(s):  
Yujian Ren ◽  
Jingxiang Li ◽  
Yuanzhe Dong ◽  
Dong Jin ◽  
Shengdun Zhao
Keyword(s):  
Acoustic Emission ◽  
High Frequency ◽  
Control Method ◽  
Low Cycle Fatigue ◽  
Control Strategies ◽  
Low Frequency ◽  
Loading Frequency ◽  
Cycle Fatigue ◽  
Al 6061 ◽  
Whole Process

Abstract High efficiency and good section quality are two main objectives of metal bar cropping. A suitable control method can help to achieve both goals. An investigation of the control method of low-cycle fatigue cropping (LCFC) based on the acoustic emission (AE) technique has been proposed in this study. Ring-down counts and kurtosis are used to monitor the whole process of LCFC. The results showed that kurtosis is more suitable for monitoring the LCFC process and as a critical parameter to optimize the control method than ring-down counts in the noisy factory environment.Moreover, three types of materials are studied in this experiment; by combine with the AE results, macroscopic images and microscopic images of sections, characteristics of various LCFC stages are obtained. The results also indicated reduce the area of the transient fracture zone is the key to improve the section quality. Reducing the load frequency before the unstable crack propagation stage will beneficial to realize the goals. Based on the evaluation of kurtosis, an optimized control method is presented, and two control parameters: transient time T and the critical value of the slope of kurtosis C are determined. For 16Mn, 1045 and Al 6061, the T is 5s, 10s, and 1s, respectively. For 16Mn, 1045, and Al 6061, the C is 100, 300, and 0, respectively. Two parameters, h and S, are used to evaluate the section quality and four control strategies are compared. The results indicate the optimal control methods can improve the section quality effectively. The influence trend of reducing loading frequency is investigated by further comparison. It can be seen as the frequency decreases, the efficiency of the section quality improving decreases. In order to realize the optimal results, different control strategies are adopted for different materials. Strategy 1 (high frequency is 20Hz，high frequency thought the whole process), strategy 2 (high frequency is 20Hz，low frequency is 8.33Hz), and strategy 3 (high frequency is 20Hz，low frequency is 6.67Hz) is suitable for Al 6061, 1045, and 16Mn, respectively.

Sign in / Sign up

Export Citation Format

Share Document