Modeling the Lubrication, Dynamics, and Effects of Piston Dynamic Tilt of Twin-Land Oil Control Rings in Internal Combustion Engines

1999 ◽  
Vol 122 (1) ◽  
pp. 119-129 ◽  
Author(s):  
T. Tian ◽  
V. W. Wong
Keyword(s):  
Film Thickness ◽  
Internal Combustion Engines ◽  
Three Dimensional ◽  
Internal Combustion ◽  
Asperity Contact ◽  
Combustion Engines ◽  
Ring Groove ◽  
Oil Film ◽  
Oil Transport ◽  
Axial Forces

A theoretical model was developed to study the lubrication, friction, dynamics, and oil transport of twin-land oil control rings (TLOCR) in internal combustion engines. A mixed lubrication model with consideration of shear-thinning effects of multigrade oils was used to describe the lubrication between the running surfaces of the two lands and the liner. Oil squeezing and asperity contact were both considered for the interaction between the flanks of the TLOCR and the ring groove. Then, the moments and axial forces from TLOCR/liner lubrication and TLOCR/groove interaction were coupled into the dynamic equations of the TLOCR. Furthermore, effects of piston dynamic tilt were considered in a quasi three-dimensional manner so that the behaviors of the TLOCR at different circumferential locations could be studied. As a first step, variation of the third land pressure was neglected. The model predictions were illustrated via an SI engine. One important finding is that around thrust and anti-thrust sides, the difference between the minimum oil film thickness of two lands can be as high as several micrometers due to piston dynamic tilt. As a result, at thrust and anti-thrust sides, significant oil can pass under one land of the TLOCR along the bore, although the other land perfectly seals the bore. Then, the capabilities of the model were further explained by studying the effects of ring tension and torsional resistance on the lubrication and oil transport between the lands and the liner. The effects of oil film thickness on the flanks of the ring groove on the dynamics of the TLOCR were also studied. Friction results show that boundary lubrication contributes significantly to the total friction of the TLOCR. [S0742-4795(00)01801-9]

Experimental Investigation of Oil Accumulation in Second Land of Internal Combustion Engines

2005 ◽  
Vol 127 (1) ◽  
pp. 206-212
Author(s):  
T. Icoz ◽  
Z. Dursunkaya
Keyword(s):  
Film Thickness ◽  
Internal Combustion Engines ◽  
Internal Combustion ◽  
Engine Oil ◽  
Combustion Engines ◽  
Oil Consumption ◽  
Oil Accumulation ◽  
Oil Film ◽  
Piston Cylinder ◽  
Total Oil

Blowback of engine oil suspended in combustion gases, when the gas flows from the piston second land back into the combustion chamber, is believed to contribute to oil consumption and hydrocarbon emissions in internal combustion engines. Oil accumulation in the region between top and second compression rings is a factor that influences this phenomenon. The effects of individual parameters, such as oil film thickness and viscosity, however, have still not been understood. The present study was aimed at constructing an experimental setup to study the effect of oil film thickness on oil accumulation in the second land of internal combustion engines. Due to the inherent difficulties of experimentation on production engines, a modeled piston-cylinder assembly was constructed. Total oil accumulation in the modeled second land after a single piston stroke was measured and compared to oil consumption in operating engines.

Piston Rings Friction Comparison in a Free Piston and Conventional Crankshaft Engines

2018 ◽  
Author(s):  
Mehar Bade ◽  
Nigel N. Clark ◽  
Terence Musho ◽  
Parviz Famouri
Keyword(s):  
Film Thickness ◽  
Internal Combustion Engines ◽  
Asperity Contact ◽  
Combustion Engines ◽  
Power Losses ◽  
Piston Rings ◽  
Free Piston ◽  
Oil Film ◽  
Frictional Losses ◽  
Free Piston Engine

The conventional internal combustion engines driven by crankshafts and connecting rod mechanisms are restrained by combustion, thermal and mechanical inefficiencies. The Oscillating Free Piston Linear Engine Alternator (OFPLEA) produces electric power with no need to modify the reciprocating motion to rotary motion. In the most common geometry it consists of a linear alternator driven cyclically by one or two internal combustion engines. With the elimination of crankshaft mechanism linkages, the free piston engine offers potential benefits over crankshaft engines in terms of total mechanical losses. A significant proportion of 5% to 12% of total fuel energy in conventional engines is consumed to overcome the frictional losses. This research investigation addresses an analytical and numerical model to simulate the tribological performance of piston rings in an OFPLEA engine. The results are then compared with results from an equivalent conventional crankshaft driven engine. This axisymmetric, mixed lubrication tribological model is developed on the hydrodynamic process defined by Patir and Cheng’s modified Reynolds equation and an asperity contact process as defined by Greenwood and Tripp’s rough surface dry contact model. The asperity contact pressure distribution, hydrodynamic pressure distribution, lubricant oil film thickness, frictional force and frictional power losses are calculated using an explicit finite difference approach. In the absence of spring-dominated OFPLEA system, dissimilarity in the piston motion profile for compression and power stroke exhibited two different oil film thickness peaks. Whereas a similar oil film thickness peaks are observed for conventional engine due to the controlled and stable operation maintained by crankshaft mechanism. The simulation results state that the frictional losses due to piston ring - cylinder liner contact are found to be lower for a free piston engine than for those of a corresponding crankshaft engine. The simulated piston ring frictional power losses are found to be 342.8 W for the OFPLEA system and 382.6 W for the crankshaft engine. Further, an overall system efficiency improvement of 0.6 % is observed for an OFPLEA engine due to these reduced frictional losses from piston rings.

An Analysis of Ring Temperature, Oil Film Temperature and Oil Film Thickness on a Piston Ring of an IC Engine in Consideration of Ring Movement: Effect of Ring Sliding Face Profile

2007 ◽  
Author(s):  
Takashi Ishijima ◽  
Akiko Shimada ◽  
Shinichiro Kodaira ◽  
Hiroshi Sakamoto ◽  
Yasuo Harigaya ◽  
...  
Keyword(s):  
Film Thickness ◽  
Internal Combustion Engines ◽  
Piston Ring ◽  
Characteristic Temperature ◽  
Combustion Engines ◽  
Ring Groove ◽  
Ic Engine ◽  
Lower Face ◽  
Oil Film ◽  
Movement Effect

For the clarification of the lubrication and thermal problems between ring and liner of internal combustion engines, an unsteady thermohydrodynamic lubrication model considering the ring temperature and the ring movement in the piston ring groove was developed. Then using the method of thermohydrodynamic lubrication, the effect of the profile of top ring sliding face on the oil film thickness and friction losses was analyzed. The ring is width of 3mm and thickness of 4.5mm. Profiles in sliding face of the ring used are two types. Ring 1 has a flat in the middle and a roundness in the corner, and Ring 2 has a barrel face. The ring temperature on the sliding surface shows the characteristic temperature distribution, and the temperature difference between ring lower face and middle of ring has about 19 °C. The oil film thickness changed in a cycle increases with increase of barrel height. The friction mean effective pressure FMEP decreases with the increase of barrel height both Ring 1 and Ring 2. FMEP of Ring 2 is more effective than that of Ring 1.

Nonlinear Transient Response of a High Speed Driven Valve System and Stresses in Valve Springs for Internal Combustion Engines

1989 ◽  
Vol 111 (3) ◽  
pp. 264-271 ◽  
Author(s):  
K. Nagaya
Keyword(s):  
High Speed ◽  
Internal Combustion Engines ◽  
Three Dimensional ◽  
Beam Theory ◽  
Internal Combustion ◽  
Valve Train ◽  
Combination Method ◽  
Combustion Engines ◽  
Valve System ◽  
Cam Profile

This paper presents a method for solving the dynamic response problems of a driven valve system and the stress problem of valve springs for internal combustion engines. In this system there is hysteresis behavior in the spring constants during the rotation of the cam shaft. To treat this nonlinearity, the rigidity of each section is assumed to be one of a partly linear spring. For the valve trains, the cam profile is complex in general. To treat a general cam profile, this paper applies a combination method of the Fourier expansion, the Laplace transform and the analytical connection methods, and gives a response of valve trains. This paper also presents a theoretical result for the stresses in the valve spring due to the motion of the valve train based on the three dimensional curved beam theory.

scholarly journals Modeling the Fatigue Wear of the Cylinder Liner in Internal Combustion Engines during the Break-In Period and Its Impact on Piston Ring Lubrication

Lubricants ◽  
2019 ◽  
Vol 7 (10) ◽  
pp. 89
Author(s):  
Chongjie Gu ◽  
Renze Wang ◽  
Tian Tian
Keyword(s):  
Internal Combustion Engines ◽  
Cylinder Liner ◽  
Internal Combustion ◽  
Asperity Contact ◽  
Combustion Engines ◽  
Fatigue Wear ◽  
Wear Model ◽  
Surface Finishes ◽  
Liner Surface ◽  
Piston Ring Lubrication

In internal combustion engines, a significant portion of the total fuel energy is consumed to overcome the mechanical friction between the cylinder liner and the piston rings. The engine work loss through friction gradually reduces during the engine break-in period, as the result of liner surface topography changes caused by wear. This work is the first step toward the development of a physics-based liner wear model to predict the evolution of liner roughness and ring pack lubrication during the break-in period. Two major mechanisms are involved in the wear model: plastic deformation and asperity fatigue. The two mechanisms are simulated through a set of submodels, including elastoplastic asperity contact, crack initiation, and crack propagation within the contact stress field. Compared to experimental measurements, the calculated friction evolution of different liner surface finishes during break-in exhibits the same trend and a comparable magnitude. Moreover, the simulation results indicate that the liner wear rate or duration of break-in depends greatly on the roughness, which may provide guidance for surface roughness design and manufacturing processes.

An analytical study of tribological parameters between piston ring and cylinder liner in internal combustion engines

2016 ◽  
Vol 230 (4) ◽  
pp. 329-349 ◽  
Author(s):  
Mohamed Kamal Ahmed Ali ◽  
Hou Xianjun ◽  
Richard Fiifi Turkson ◽  
Muhammad Ezzat
Keyword(s):  
Film Thickness ◽  
Internal Combustion Engines ◽  
Piston Ring ◽  
Cylinder Liner ◽  
Combustion Engines ◽  
Oil Viscosity ◽  
Oil Film ◽  
Ring Assembly ◽  
Ring Dynamics ◽  
Tribological Parameters

This paper presents a model to study the effect of piston ring dynamics on basic tribological parameters that affect the performance of internal combustion engines by using dynamics analysis software (AVL Excite Designer). The paramount tribological parameters include friction force, frictional power losses, and oil film thickness of piston ring assembly. The piston and rings assembly is one of the highest mechanically loaded components in engines. Relevant literature reports that the piston ring assembly accounts for 40% to 50% of the frictional losses, making it imperative for the piston ring dynamics to be understood thoroughly. This analytical study of the piston ring dynamics describes the significant correlation between the tribological parameters of piston and rings assembly and the performance of engines. The model was able to predict the effects of engine speed and oil viscosity on asperity and hydrodynamic friction forces, power losses, oil film thickness and lube oil consumption. This model of mixed film lubrication of piston rings is based on the hydrodynamic action described by Reynolds equation and dry contact action as described by the Greenwood–Tripp rough surface asperity contact model. The results in the current analysis demonstrated that engine speed and oil viscosity had a remarkable effect on oil film thickness and hydrodynamic friction between the rings and cylinder liner. Hence, the mixed lubrication model, which unifies the lubricant flow under different ring–liner gaps, is needed via the balance between the hydrodynamic and boundary lubrication modes to obtain minimum friction between rings and liner and to ultimately help in improving the performance of engines.

Sign in / Sign up

Export Citation Format

Share Document