scholarly journals Comparison of Coriolis and Turbine Type Flow Meters for Fuel Measurement in Gas Turbine Testing

1993 ◽  
Author(s):  
J. D. MacLeod ◽  
W. Grabe
Keyword(s):  
Steady State ◽  
Gas Turbine ◽  
Mass Flow ◽  
Gas Turbines ◽  
Gas Turbine Engine ◽  
Turbine Engine ◽  
Turbine Flowmeter ◽  
Turbine Performance ◽  
Coriolis Flowmeter ◽  
Project Objectives

The Machinery and Engine Technology (MET) Program of the National Research Council of Canada (NRCC) has established a program for the evaluation of sensors to measure gas turbine engine performance accurately. The precise measurement of fuel flow is an essential part of steady-state gas turbine performance assessment. Prompted by an international engine testing and information exchange program, and a mandate to improve all aspects of gas turbine performance evaluation, the MET Laboratory has critically examined two types of fuel flowmeters, Coriolis and turbine. The two flowmeter types are different in that the Coriolis flowmeter measures mass flow directly, while the turbine flowmeter measures volumetric flow, which must be converted to mass flow for conventional performance analysis. The direct measurement of mass flow, using a Coriolis flowmeter, has many advantages in field testing of gas turbines, because it reduces the risk of errors resulting from the conversion process. Turbine flowmeters, on the other hand, have been regarded as an industry standard because they are compact, rugged, reliable, and relatively inexpensive. This paper describes the project objectives, the experimental installation, and the results of the comparison of the Coriolis and turbine type flowmeters in steady-state performance testing. Discussed are variations between the two types of flowmeters due to fuel characteristics, fuel handling equipment, acoustic and vibration interference and installation effects. Also included in this paper are estimations of measurement uncertainties for both types of flowmeters. Results indicate that the agreement between Coriolis and turbine type flowmeters is good over the entire steady-state operating range of a typical gas turbine engine. In some cases the repeatability of the Coriolis flowmeter is better than the manufacturers specification. Even a significant variation in fuel density (10%), and viscosity (300%), did not appear to compromise the ability of the Coriolis flowmeter to match the performance of the turbine flowmeter.

Comparison of Coriolis and Turbine-Type Flowmeters for Fuel Measurement in Gas Turbine Testing

1995 ◽  
Vol 117 (1) ◽  
pp. 132-137 ◽  
Author(s):  
J. D. MacLeod ◽  
W. Grabe
Keyword(s):  
Steady State ◽  
Gas Turbine ◽  
Mass Flow ◽  
Gas Turbines ◽  
Gas Turbine Engine ◽  
Turbine Engine ◽  
Turbine Flowmeter ◽  
Turbine Performance ◽  
Coriolis Flowmeter ◽  
Project Objectives

The Machinery and Engine Technology (MET) Program of the National Research Council of Canada (NRCC) has established a program for the evaluation of sensors to measure gas turbine engine performance accurately. The precise measurement of fuel flow is an essential part of steady-state gas turbine performance assessment. Prompted by an international engine testing and information exchange program, and a mandate to improve all aspects of gas turbine performance evaluation, the MET Laboratory has critically examined two types of fuel flowmeters, Coriolis and turbine. The two flowmeter types are different in that the Coriolis flowmeter measures mass flow directly, while the turbine flowmeter measures volumetric flow, which must be converted to mass flow for conventional performance analysis. The direct measurement of mass flow, using a Coriolis flowmeter, has many advantages in field testing of gas turbines, because it reduces the risk of errors resulting from the conversion process. Turbine flowmeters, on the other hand, have been regarded as an industry standard because they are compact, rugged, reliable, and relatively inexpensive. This paper describes the project objectives, the experimental installation, and the results of the comparison of the Coriolis and turbine-type flowmeters in steady-state performance testing. Discussed are variations between the two types of flowmeters due to fuel characteristics, fuel handling equipment, acoustic and vibration interference, and installation effects. Also included in this paper are estimations of measurement uncertainties for both types of flowmeter. Results indicate that the agreement between Coriolis and turbine-type flowmeters is good over the entire steady-state operating range of a typical gas turbine engine. In some cases the repeatability of the Coriolis flowmeter is better than the manufacturer’s specification. Even a significant variation in fuel density (10 percent), and viscosity (300 percent) did not appear to compromise the ability of the Coriolis flowmeter to match the performance of the turbine flowmeter.

scholarly journals Turbine Rebuild Effects on Gas Turbine Performance

1992 ◽  
Author(s):  
J. D. MacLeod ◽  
B. Drbanski
Keyword(s):  
Gas Turbine ◽  
National Research Council ◽  
Engine Performance ◽  
Gas Turbine Engine ◽  
Turbine Engine ◽  
New Methods ◽  
Turbine Performance ◽  
Turboprop Engine ◽  
Project Objectives ◽  
Performance Variations

The Engine Laboratory of the National Research Council of Canada (NRCC), with the assistance of Standard Aero Ltd., has established a program for the evaluation of component deterioration on gas turbine engine performance. As part of this project, a study of the effects of turbine rebuild tolerances on overall engine performance was undertaken. This study investigated the range of performance changes that might be expected for simply disassembling and reassembling the turbine module of a gas turbine engine, and how these changes would influence the results of the component fault implantation program. To evaluate the effects of rebuilding the turbine on the performance of a single spool engine, such as Allison T56 turboprop engine, a series of three rebuilds were carried out. This study was performed in a similar way to a previous NRCC study on the effects of compressor rebuilding. While the compressor rebuild study had found performance changes in the order of 1% on various engine parameters, the effects of rebuilding the turbine have proven to be even more significant. Based on the results of the turbine rebuild study, new methods to improve the assurance of the best possible tolerances during the rebuild process are currently being addressed. This paper describes the project objectives, the experimental installation, and the results of the performance evaluations. Discussed are performance variations due to turbine rebuilds on engine performance characteristics. As the performance changes were significant, a rigorous measurement uncertainty analysis is included.

Improving Gas Turbine Performance Through Reassembling Degraded Components: An Experimental and Computational Study

2020 ◽  
Author(s):  
Shuocheng Xia ◽  
Zhongran Chi ◽  
Shusheng Zang ◽  
Hui Wang
Keyword(s):  
Gas Turbine ◽  
Test Data ◽  
Thermal Efficiency ◽  
Gas Turbines ◽  
Computational Study ◽  
Low Cost ◽  
Gas Turbine Engine ◽  
Performance Degradation ◽  
Turbine Engine ◽  
Turbine Performance

Abstract Performance degradation of gas turbine is a common phenomenon during operation. Maintenance of the degraded gas turbines and improving their performance at a low cost are important in engineering. In this paper, the maintenance method based on reassembling degraded components of existing gas turbines was studied. This research was based on a type of 2MW gas turbine engine. Blue ray scanning was carried out to rebuild the 3D flow-path geometries of the compressor and turbine of a degraded engine. Then CFD simulations were carried out to compare the characteristic maps of new and degraded components. Secondly, performance tests of six engines were carried out. A correction method was developed to get the specific component characteristics using test data, which can also analyze and quantify the degradations. Also, a gas turbine performance prediction program was used to find the promising component-exchange plan within 5 given gas turbines to improve total thermal efficiency. Finally, additional test was carried out to verify the performance of the reassembled gas turbine. Through the developed method including 3D scanning, CFD simulation, and correction of component characteristics with engine test data, the component performance degradation of a specific gas turbine can be obtained in quantity. The gas turbine performance predictions based on the acquired characteristic maps showed good agreement with test data. With the help of the method developed in this work, a new gas turbine engine was obtained through exchanging the components of degraded engines, which is at a very low cost and in a short time. The improvement in total thermal efficiency was about 0.3 percentage, which was verified by engine tests.

Combustor Rebuild Effects on Gas Turbine Performance

1995 ◽  
Author(s):  
J. D. MacLeod ◽  
B. Barry
Keyword(s):  
Gas Turbine ◽  
National Research Council ◽  
Engine Performance ◽  
Gas Turbine Engine ◽  
Performance Characteristics ◽  
Turbine Engine ◽  
Turbine Performance ◽  
Turboprop Engine ◽  
Project Objectives ◽  
Performance Variations

The Institute for Aerospace Research of the National Research Council of Canada (NRCC), has established a program for the evaluation of component deterioration on gas turbine engine performance. The effort is aimed at investigating the effects of typical in-service faults on the performance characteristics of each individual engine component. As part of this project, a study of the effects of combustor rebuild tolerances on overall engine performance was undertaken. This study investigated the range of performance changes that might be expected for simply disassembling and reassembling the combustor module of a gas turbine engine, and how these changes would influence the results of any component modification testing. To evaluate the effects of rebuilding the combustor on the performance of a single spool engine, such as an Allison T56 turboprop engine, a series of three rebuilds was carried out. This study was performed in a similar way to two previous NRCC studies on the effects of compressor and turbine rebuilding. While the compressor and turbine rebuild studies found performance changes in the order of I% on various engine parameters, the effects of rebuilding the combustor have proven to be of similar magnitude. Based on the results of the combustor rebuild study, new methods to improve the assurance of the best possible tolerances during the rebuild process are currently being addressed. This paper describes the project objectives, the experimental installation, and the results of the performance evaluations. Discussed are performance variations due to combustor rebuilds on engine performance characteristics. As the performance changes were significant, a rigorous measurement uncertainty analysis is included.

Training Future Gas Turbine Performance Engineers

2007 ◽  
Author(s):  
V. Pachidis ◽  
P. Pilidis ◽  
I. Li
Keyword(s):  
Gas Turbine ◽  
Thermal Power ◽  
Engine Performance ◽  
Gas Turbine Engine ◽  
Performance Simulation ◽  
Turbine Engine ◽  
Turbine Performance ◽  
Auxiliary Power ◽  
Engine Testing ◽  
The Uk

The performance analysis of modern gas turbine engine systems has led industry to the development of sophisticated gas turbine performance simulation tools and the utilization of skilled operators who must possess the ability to balance environmental, performance and economic requirements. Academic institutions, in their training of potential gas turbine performance engineers have to be able to meet these new challenges, at least at a postgraduate level. This paper describes in detail the “Gas Turbine Performance Simulation” module of the “Thermal Power” MSc course at Cranfield University in the UK, and particularly its practical content. This covers a laboratory test of a small Auxiliary Power Unit (APU) gas turbine engine, the simulation of the ‘clean’ engine performance using a sophisticated gas turbine performance simulation tool, as well as the simulation of the degraded performance of the engine. Through this exercise students are expected to gain a basic understanding of compressor and turbine operation, gain experience in gas turbine engine testing and test data collection and assessment, develop a clear, analytical approach to gas turbine performance simulation issues, improve their technical communication skills and finally gain experience in writing a proper technical report.

Low Emission Variable Area Combustor for Vehicular Gas Turbines

1973 ◽  
Vol 95 (3) ◽  
pp. 191-198 ◽  
Author(s):  
D. J. White ◽  
P. B. Roberts ◽  
W. A. Compton
Keyword(s):  
Power Systems ◽  
Gas Turbine ◽  
Environmental Protection Agency ◽  
Gas Turbines ◽  
Gas Turbine Engine ◽  
Protection Agency ◽  
Engine Emissions ◽  
Turbine Engine ◽  
Automotive Engine ◽  
Low Emission

In recent years automotive engine emissions have become subject to stringent Federal legislation. The most severe of these regulations pertains to the 1976 Emission Standards as defined by the Advanced Automotive Power Systems (AAPS) Division of the Environmental Protection Agency (EPA). A unique combustor concept has been developed by Solar which has demonstrated the feasibility of meeting these emission requirements. The integrated emissions of a typical regenerative gas turbine engine employing this combustor type were each below one half of the levels specified by the Federal 1976 Standards, when tested over a simulated federal driving cycle. The success of the feasibility tests for this combustor concept has lead to more fundamental studies and the planned development of a prototype combustor for demonstration on the EPA-AAPS baseline gas turbine engine. The prototype combustor for the baseline engine is described together with its variable area port mechanisms, which has been demonstrated as necessary for emission control.

A Simple Thermal Model of Bearings With Transient Effects

2010 ◽  
Author(s):  
Karleine M. Justice ◽  
Ian Halliwell ◽  
Jeffrey S. Dalton
Keyword(s):  
Steady State ◽  
Gas Turbine ◽  
Thermal Management ◽  
Heat Load ◽  
Transient Behavior ◽  
Gas Turbine Engine ◽  
System Level ◽  
Lubrication System ◽  
Transient Effects ◽  
Turbine Engine

In thermal management, system-level models provide an understanding of interactions between components and integration constraints — issues which are exacerbated by tighter coupling in both real life and simulation. A simple model of the steady-state thermal characteristics of the bearings in a two-spool turbofan engine has been described in previous work [1], where it was compared with a more comprehensive tribology-based simulation. Since failure is more likely to occur during transient rather than steady-state operating conditions, it is important that transient behavior is also studied. Therefore, development of models capable of capturing transient system-level performance in air vehicles is critical. In the current paper, the former simple model is used for the generation of a method to replicate the transient effects of heat loads within the lubrication system of a gas turbine engine. The simple engine model that defined the lubrication system is representative of a twin-spool, mid-size, high bypass ratio turbofan used in commercial transport. In order to demonstrate the range and versatility of the parametric heat load model, the model is now applied to the transient operation of a low-thrust unmanned aerial vehicle (UAV) engine, similar to that found on the Global Hawk. There are five separate bearings in the oil loop model and four separate oil sump locations. Contributions to the heat load calculations are heat transfer through the bearing housings and friction caused by station temperatures and shaft speeds, respectively. The lubrication system has been simplified by applying general assumptions for a proof-of-concept of the new transient parametric model. The fuel flow rate for the fuel-cooled oil cooler (FCOC) is set via the full authority digital electronic control (FADEC) in the transient engine model which is coupled to the parametric heat load model. Initially, it is assumed that total heat transfer from the bearings to the oil correspond to oil temperature changes of 150–250°F (83–139°C). The results show that successful modeling of the transient behavior on the thermal effects in the bearings of a gas turbine engine using the MATLAB/Simulink environment have been achieved. This is a valuable addition to the previous steady-state simulation, and the combined tools may be used as part of a more sophisticated thermal management system. Because it is so simple and scalable, the tool enables thermal management issues to be addressed in the preliminary design phase of a gas turbine engine development program.

Exploration of Compact Combustors for Reheat Cycle Aero Engine Applications

2006 ◽  
Author(s):  
J. Zelina ◽  
D. T. Shouse ◽  
J. S. Stutrud ◽  
G. J. Sturgess ◽  
W. M. Roquemore
Keyword(s):  
Gas Turbine ◽  
Temperature Rise ◽  
Gas Turbines ◽  
Gas Turbine Engine ◽  
Operating Conditions ◽  
Combustion System ◽  
Turbine Engine ◽  
Lean Blowout ◽  
Power Extraction ◽  
Wide Range

An aero gas turbine engine has been proposed that uses a near-constant-temperature (NCT) cycle and an Inter-Turbine Burner (ITB) to provide large amounts of power extraction from the low-pressure turbine. This level of energy is achieved with a modest temperature rise across the ITB. The additional energy can be used to power a large geared fan for an ultra-high bypass ratio transport aircraft, or to drive an alternator for large amounts of electrical power extraction. Conventional gas turbines engines cannot drive ultra-large diameter fans without causing excessively high turbine temperatures, and cannot meet high power extraction demands without a loss of engine thrust. Reducing the size of the combustion system is key to make use of a NCT gas turbine cycle. Ultra-compact combustor (UCC) concepts are being explored experimentally. These systems use high swirl in a circumferential cavity about the engine centerline to enhance reaction rates via high cavity g-loading on the order of 3000 g’s. Any increase in reaction rate can be exploited to reduce combustor volume. The UCC design integrates compressor and turbine features which will enable a shorter and potentially less complex gas turbine engine. This paper will present experimental data of the Ultra-Compact Combustor (UCC) performance in vitiated flow. Vitiation levels were varied from 12–20% oxygen levels to simulate exhaust from the high pressure turbine (HPT). Experimental results from the ITB at atmospheric pressure indicate that the combustion system operates at 97–99% combustion efficiency over a wide range of operating conditions burning JP-8 +100 fuel. Flame lengths were extremely short, at about 50% of those seen in conventional systems. A wide range of operation is possible with lean blowout fuel-air ratio limits at 25–50% below the value of current systems. These results are significant because the ITB only requires a small (300°F) temperature rise for optimal power extraction, leading to operation of the ITB at near-lean-blowout limits of conventional combustor designs. This data lays the foundation for the design space required for future engine designs.

Experimental Results of Hot Section Metal Temperature Measurements of Rolls-Royce Allison 501KH Under Massive Steam Injection

2002 ◽  
Author(s):  
Dah Yu Cheng ◽  
Albert L. C. Nelson
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Steam Injection ◽  
Gas Turbine Engine ◽  
Injection Rate ◽  
Experimental Results ◽  
Turbine Engine ◽  
Second Stage ◽  
Before And After ◽  
Internally Cooled

It has always been thought by the gas turbine industry that steam injection will shorten the effective life of certain gas turbine parts. Recently it was shown that a number of steam injected Cheng Cycle Rolls-Royce Allison 501KH gas turbines, accumulated more than 2.5 million logged hours of operation and with a prolonged parts life. The “hot parts” of a Rolls-Royce Allison 501KH gas turbine engine that are of concern, are the first stage nozzle, the first stage blade, and the second stage nozzle. These parts are all air cooled through the first stages internal passages. (The second stage blades and on down are not internally cooled.) The concern raised in many gas turbine institutions is that the metal temperatures of these hot parts, due to the heat conductivity properties of injected steam, will make them deteriorate faster. An experiment was completed using a steam injected Cheng Cycle, on an Allison 501KH gas turbine engine. In the experiment, a substantial number of thermocouples were attached to the surfaces of the turbines hot parts. This engine had a steam injection rate of up to 18% airflow. The experimental results showed that if steam could be properly mixed with the cooling air before the air enters into the cooling passages of the hot parts, the metal temperatures did not increase. During the operation of the engines, it was recorded that the hot parts lifetime increased from 25,000 hours before the hot parts section had to be overhauled, to 42,000 hours (on average) before they needed to be overhauled. This paper will report the measurement installation in detail. The results before and after steam injection in the hot parts sections of the Rolls-Royce Allison 501KH engine will also be discussed.

Technological Trend of Aircraft Gas Turbines and its Effect on the Development for Ship Propulsion Plants

1970 ◽  
Author(s):  
N. K. H. Scholz
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Gas Turbine Engine ◽  
Design Parameters ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Compression Pressure ◽  
Turbine Engine ◽  
Ship Propulsion

The effect of the main design parameters of the aero gas turbine engine cycle, namely combustion temperature and compression pressure ratio, on the specific performance values is discussed. The resulting development trend has been of essential influence on the technology. Relevant approaches are outlined. The efforts relating to weight and manufacturing expense are also indicated. In the design of aero gas turbine engines increasing consideration is given to the specific flight mission requirements, such as for instance by the introduction of the by-pass principle. Therefore direct application of aero gas turbine engines for ship propulsion without considerable modifications, as has been practiced in the past, is not considered very promising for the future. Nevertheless, there are possibilities to take advantage of aero gas turbine engine developments for ship propulsion systems. Appropriate approaches are discussed. With the experience obtained from aero gas turbine engines that will enter service in the early seventies it should be possible to develop marine gas turbine engines achieving consumptions and lifes that are competitive with those of advanced diesel units.

Sign in / Sign up

Export Citation Format

Share Document