scholarly journals Hybrid Ceramic Bearing Development for Gas Turbine Engines

1994 ◽  
Author(s):  
Frederick D. Slaney
Keyword(s):  
Silicon Nitride ◽  
Gas Turbine ◽  
High Speed ◽  
Development Program ◽  
Operating Conditions ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Hybrid Bearing ◽  
Engine Testing ◽  
Hybrid Ceramic

Over the past seven years, an extensive hybrid bearing development program has been conducted at Textron Lycoming. This paper will report the details of testing and the extraordinary results which can be obtained with silicon nitride balls as applied in hybrid bearings on gas turbine engines. This paper describes the analytically predicted advantages which low mass silicon nitride balls offer at speeds over 2.0MDN. Rig testing comparing hybrid bearings to standard bearings is reported. Testing included heat generation evaluation which showed that hybrid bearings generate an average of 40% less heat than standard bearings. Rig simulation of the AGT1500 mission duty cycle demonstrated that the hybrid silicon nitride bearing system is robust enough to handle the most severe operating conditions. Testing under severe slipping/skidding conditions demonstrated good resistance to skid failure. Under conditions selected to produce high wear, no wear was induced in a hybrid bearing while severe wear was induced in the M50 steel bearing. These preliminary successes lead to active engine testing on the AGT1500 and a new test program to demonstrate operation at 4.0 MDN. As a result of these programs Textron Lycoming now considers hybrid ceramic bearings as a viable design to be used in high speed development applications. This paper provides design detail and test data covering the work outlined above.

Renovation features of powder high-speed steels broaches with plazma hardening

2021 ◽  
pp. 82-85
Author(s):  
A.S. Politov ◽  
R.R. Latypov
Keyword(s):  
Gas Turbine ◽  
Comparative Studies ◽  
High Speed ◽  
Atmospheric Plasma ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Cold Atmospheric Plasma ◽  
Plasma Hardening

The comparative studies results of the durability of cutting properties of new and restored by regrinding and repeated plasma hardening with the application of multi-layer Si—O—C—N nanocoating system (PECVD by cold atmospheric plasma) powder high — speed steels broaches teeth for the processing of hard-to-process materials profilecomposite gas-turbine engines components are presented.

scholarly journals Development of 300 kW Class Ceramic Gas Turbine (CGT302)

1995 ◽  
Author(s):  
Kozi Nishio ◽  
Junzo Fujioka ◽  
Tetsuo Tatsumi ◽  
Isashi Takehara
Keyword(s):  
Gas Turbine ◽  
Development Program ◽  
Pollutant Emissions ◽  
Turbine Engines ◽  
Inlet Temperature ◽  
Gas Turbine Engines ◽  
Turbine Inlet Temperature ◽  
Iso Standard ◽  
Current State ◽  
Ceramic Components

With the aim of achieving higher efficiency, lower pollutant emissions, and multi-fuel capability for small to medium-sized gas turbine engines for use in co-generation systems, a ceramic gas turbine (CGT) research and development program is being promoted by the Japanese Ministry of International Trade and Industry (MITI) as a part of its “New Sunshine Project”. Kawasaki Heavy Industries (KHI) is participating in this program and developing a regenerative two-shaft CGT (CGT302). In 1993, KHI conducted the first test run of an engine with full ceramic components. At present, the CGT302 achieves 28.8% thermal efficiency at a turbine inlet temperature (TIT) of 1117°C under ISO standard conditions and an actual TIT of 1250°C has been confirmed at the rated speed of the basic CGT. This paper consists of the current state of development of the CGT302 and how ceramic components are applied.

Engine Test Experience and Characterization of Self Sealing Ceramic Matrix Composites for Nozzle Applications in Gas Turbine Engines

2003 ◽  
Author(s):  
Eric P. Bouillon ◽  
Patrick C. Spriet ◽  
Georges Habarou ◽  
Thibault Arnold ◽  
Greg C. Ojard ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Elevated Temperatures ◽  
Low Cycle Fatigue ◽  
Ceramic Matrix Composites ◽  
Ceramic Matrix ◽  
Turbine Engines ◽  
Matrix Composites ◽  
Gas Turbine Engines ◽  
Sic Fiber ◽  
Engine Testing

Advanced materials are targeting durability improvement in gas turbine engines. One general area of concern for durability is in the hot section components of the engine. Ceramic matrix composites offer improvements in durability at elevated temperatures with a corresponding reduction in weight for nozzles of gas turbine engines. Building on past material efforts, ceramic matrix composites using a carbon and a SiC fiber with a self-sealing matrix have been developed for gas turbine applications. Prior to ground engine testing, a reduced test matrix was undertaken to aggressively test the material in a long-term hold cycle at elevated temperatures and environments. This tensile low cycle fatigue testing was done in air and a 90% steam environment. After completion of the aggressive testing effort, six nozzle seals were fabricated and installed in an F100-PW-229 engine for accelerated mission testing. The C fiber CMC and the SiC Fiber CMC were respectively tested to 600 and 1000 hours in accelerated conditions without damage. Engine testing is continuing to gain additional time and insight with the objective of pursuing the next phase of field service evaluation. Mechanical testing and post-test characterization results of this testing will be presented. The results of the engine testing will be shown and overall conclusions drawn.

Marine Operation of Gas Turbine Engines and Waterjet Pumps for Small Passenger Vessels

1979 ◽  
Author(s):  
S. M. Kowleski ◽  
C. D. Harrington
Keyword(s):  
Gas Turbine ◽  
San Francisco ◽  
High Speed ◽  
San Francisco Bay ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Golden Gate ◽  
Operational Problem ◽  
Golden Gate Bridge ◽  
Selection Of

This paper describes the planning, developmental, equipment selection and operational problem phases of the high-speed ferry system presently being operated on San Francisco Bay by the Golden Gate Bridge, Highway and Transportation District. The reasons for the selection of the vessel propulsion package consisting of gas turbine engines and waterjet pumps are discussed in some detail. Most importantly, the paper covers the problems experienced to date with this equipment in continuous marine operation.

U.S. Navy Development of Air Assist Fuel Nozzle System for the 501K Series Gas Turbine Engines

2002 ◽  
Author(s):  
Matthew G. Hoffman ◽  
Richard J. DeCorso ◽  
Dennis M. Russom
Keyword(s):  
Gas Turbine ◽  
Failure Modes ◽  
Development Program ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Engine Operation ◽  
Air Blast ◽  
Blast Design ◽  
Fuel Nozzle ◽  
The U.S

The U.S. Navy has experienced problems with liquid fuel nozzles used on the Rolls Royce (formerly Allison) 501K series marine gas turbine engines. The 501K engines used by the U.S. Navy power Ship Service Gas Turbine Generators (SSGTGs) on a number of destroyer and cruiser class ships. Over roughly the last 25 years, 3 different nozzle designs have been employed, the latest and current nozzle being a piloted air blast design. The primary failure modes of these designs were internal fuel passage coking and external carbon deposits. The current piloted air blast design has a hard time replacement requirement of 1500 hours. This life is considered unacceptable. To improve fuel nozzle life, the Navy and Turbine Fuel Technologies (formerly Delavan) teamed in a fast track program to develop a new fuel nozzle with a target life of 5000 hours and 500 starts. As a result, an air assist/air blast nozzle was developed and delivered in approximately 6 months. In addition to the nozzle itself, a system was developed to provide assist air to the fuel nozzles to help atomize the fuel for better ignition. Nozzle sets and air assist systems have been delivered and tested at the NSWC Philadelphia LBES (Land Based Engineering Site). In addition, nozzle sets have been installed aboard operating ships for in-service evaluations. During the Phase one evaluation (July 2000 to June 2001) aboard USS Porter (DDG 78) a set of nozzles accumulated over 3500 hours of trouble free operation, indicating the target of 5000 hours is achievable. As of this writing these nozzles have in excess of 5700 hours. The improvements in nozzle life provided by the new fuel nozzle design will result in cost savings through out the life cycle of the GTGS. In fact, the evaluation nozzles are already improving engine operation and reliability even before the nozzles’ official fleet introduction. This paper describes the fuel nozzle and air assist system development program and results of OEM, LBES and fleet testing.

scholarly journals Generalized High Speed Simulation of Gas Turbine Engines

1990 ◽  
Author(s):  
Nanahisa Sugiyama
Keyword(s):  
Real Time ◽  
Gas Turbine ◽  
Gas Turbines ◽  
High Speed ◽  
Power Plants ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Jet Engines ◽  
Industrial Gas Turbine ◽  
High Degree

This paper describes a real-time or faster-than-real-time simulation of gas turbine engines, using an ultra high speed, multi-processor digital computer, designated the AD100. It is shown that the frame time is reduced significantly without any loss of fidelity of a simulation. The simulation program is aimed at a high degree of flexibility to allow changes in engine configuration. This makes it possible to simulate various types of gas turbine engines, including jet engines, gas turbines for vehicles and power plants, in real-time. Some simulation results for an intercooled-reheat type industrial gas turbine are shown.

Fuel Flexibility in LM2500 and LM6000 Dry Low Emission Engines

2012 ◽  
Vol 134 (5) ◽  
Author(s):  
John Blouch ◽  
Hejie Li ◽  
Mark Mueller ◽  
Richard Hook
Keyword(s):  
Gas Turbine ◽  
Operating Conditions ◽  
Inert Gases ◽  
Effect Of Temperature ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Kinetics Analysis ◽  
Fuel Flexibility ◽  
Low Emission ◽  
Commercial Operation

The LM2500 and LM6000 dry-low-emissions aeroderivative gas turbine engines have been in commercial service for 15 years and have accumulated nearly 10 × 106 hours of commercial operation. The majority of these engines utilize pipeline quality natural gas predominantly comprised of methane. There is; however, increasing interest in nonstandard fuels that contain varying levels of higher hydrocarbon species and/or inert gases. This paper reports on the demonstrated operability of LM2500 and LM6000 DLE engines with nonstandard fuels. In particular, rig tests at engine conditions were performed to demonstrate the robustness of the dual-annular counter-rotating swirlers premixer design, relative to flameholding with fuels containing high ethane, propane, and N2 concentrations. These experiments, which test the ability of the hardware to shed a flame introduced into the premixing region, have been used to expand the quoting limits for LM2500 and LM6000 gas turbine engines to elevated C2+ levels. In addition, chemical kinetics analysis was performed to understand the effect of temperature, pressure, and fuel compositions on flameholding. Test data for different fuels and operating conditions were successfully correlated with Damkohler number.

Development of FT9 Marine Gas Turbine

1981 ◽  
Author(s):  
D. A. Groghan ◽  
C. L. Miller
Keyword(s):  
Gas Turbine ◽  
Development Program ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Turbine Engine ◽  
System A ◽  
On Line ◽  
Condition Monitoring System ◽  
Industrial Gas Turbine ◽  
Engine Condition

The FT9 Marine Gas Turbine development program was initiated in August 1973 by the Naval Sea Systems Command to fulfill, in part, the requirement for a family of gas turbine engines ranging in power from 1000 to 30,000 hp. The FT9 satisfied the requirement to develop a 30,000 hp class marine gas turbine. The FT9 is a derivative of the Pratt & Whitney Aircraft JT9D engine, which powers Boeing 747, DC-10 and A300 aircraft, and of the FT4 industrial gas turbine engine. The FT9 specification also required development of an on-line engine condition monitoring system. A rigorous development test program showed the FT9 has met all specified U.S. Navy requirements and demonstrated its suitability for use in U.S. Navy combatant ships.

Fuel Flexibility in LM2500 and LM6000 Dry Low Emission Engines

2011 ◽  
Author(s):  
John Blouch ◽  
Hejie Li ◽  
Mark Mueller ◽  
Richard Hook
Keyword(s):  
Gas Turbine ◽  
Operating Conditions ◽  
Inert Gases ◽  
Effect Of Temperature ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Kinetics Analysis ◽  
Fuel Flexibility ◽  
Low Emission ◽  
Commercial Operation

The LM2500 and LM6000 dry-low-emissions (DLE) aeroderivative gas turbine engines have been in commercial service for 15 years and have accumulated nearly 10 million hours of commercial operation. The majority of these engines utilize pipeline quality natural gas predominantly comprised of methane. There is, however, increasing interest in nonstandard fuels that contain varying levels of higher hydrocarbon species and/or inert gases. This paper reports on the demonstrated operability of LM2500 and LM6000 DLE engines with nonstandard fuels. In particular, rig tests at engine conditions were performed to demonstrate the robustness of the dual-annular counter-rotating swirlers (DACRS) premixer design, relative to flameholding with fuels containing high ethane, propane, and N2 concentrations. These experiments, which test the ability of the hardware to shed a flame introduced into the premixing region, have been used to expand the quoting limits for LM2500 and LM6000 gas turbine engines to elevated C2+ levels. In addition, chemical kinetics analysis was performed to understand the effect of temperature, pressure, and fuel compositions on flameholding. Test data for different fuels and operating conditions were successfully correlated with Damkohler number.

Sign in / Sign up

Export Citation Format

Share Document