Displacement Amplifying Compliant Mechanisms for Two-Axis High-Resolution Monolithic Inertial Sensors

Author(s):  
M. Dinesh ◽  
G. K. Ananthasuresh

Novel designs for two-axis, high-resolution, monolithic inertial sensors are presented in this paper. Monolithic, i.e., joint-less single-piece compliant designs are already common in micromachined inertial sensors such as accelerometers and gyroscopes. Here, compliant mechanisms are used not only to achieve de-coupling between motions along two orthogonal axes but also to amplify the displacements of the proof-mass. Sensitivity and resolution capabilities are enhanced because the amplified motion is used for sensing the measurand. A particular symmetric arrangement of displacement-amplifying compliant mechanisms (DaCMs) leads to de-coupled and amplified motion. An existing DaCM and a new topology-optimized DaCM are presented as a building block in the new arrangement. A spring-mass-lever model is presented as a lumped abstraction of the new arrangement. This model is useful for arriving at the optimal parameters of the DaCM and for performing system-level simulation. The new designs improved the performance by a factor of two or more.

2013 ◽  
Vol 562-565 ◽  
pp. 311-316
Author(s):  
Xiao Wei Liu ◽  
Qiang Li ◽  
Guan Nan Sun ◽  
Wen Yan Liu

The theory of a Sigma-Delta modulator is introduced in this paper. Based on this theory, a feedback 2-1-1 multi-stage-noise-shaping (MASH) sigma-delta modulator is designed, and the coefficients of the modulator are calculated. The system-level simulation results show that the effective number of bits (ENOB) is 24 bits when the signal bandwidth is 1 kHz and the over-sampling (OSR) rate is 128. Then the circuits of modulator are designed, including integrator, comparator, multi-phase clock and the noise cancelling logic. The whole modulator is simulated in Cadence, the signal to noise ratio (SNR) of the modulator is 125.4dB, and the ENOB is 21.1bits, which meet the technical requirements of the sensor.


2020 ◽  
Author(s):  
Christoph Statz ◽  
Dirk Plettemeier ◽  
Yun Lu ◽  
Wolf-Stefan Benedix ◽  
Sebastian Hegler ◽  
...  

<p>Key in the interpretation and understanding of WISDOMs ground penetrating RADAR (GPR) measurements is the capability to correctly (and efficiently) simulate the instrument characteristics and the RADAR wave propagation in the Martian subsurface (the signal received by WISDOM), taking into account all relevant effects at large scale. In this contribution we present a ray tracing approach that can be applied to heterogeneous and inhomogeneous media and includes the antenna characteristics of the WISDOM instrument as well as rover structures.</p> <p>The WISDOM GPR is part of the 2022 ESA-Roscosmos ExoMars “Rosalind Franklin” rover payload. It will probe the Martian surface and subface at centimetric resolution and a penetration depth of about 3m. WISDOMs primary scientific objective is the high-resolution characterization of the material distribution within the first few meters of the Martian subsurface as a contribution to the search for evidence of past life [1] and to support the drilling operations [2].</p> <p>The simulation tool consists of two parts: The first part simulates the instrument at system level and generates the signal that is fed into the antenna as well as the receive-filter and discretization characteristic of the instrument (taking into account filters, RF effects and the ADC). The second part simulates the wave propagation of this signal in complex media (inhomogeneous or heterogeneous lossy media) taking into account polarization effects and the WISDOM antenna pattern [3]. This method is a hybrid between conventional raytracing (SBR), differential raytracing and physical optics. The simulation complexity can be granularly controlled and weighed against the level of approximation. It is capable of simulating electrically large domains with an acceptable accuracy yielding good predictions of the propagation properties in Martial soil while being significantly less computationally expensive than conventional full-wave solvers like FEM or the Finite-Differences in Time-Domain Method. <br />The results of the system-level-simulation and the propagation simulation for multiple measurement positions (along a rover track) are then combined (similar to the application of a filter) in order to generate a synthetic radargram. This radargram can be directly compared to the WISDOM measurements.</p> <p>The proposed method is validated using measurements of the WISDOM instrument at analog sites and by reference simulations using the FDTD Method [4]. We present synthetic radargrams as simulation results for several sounding scenarios including the WISDOM antenna characteristics, an inhomogeneous subsurface and lossy materials.</p> <p>The proposed approximation method yields accurate estimates of WISDOM soundings for a complex subsurface while being significantly faster than conventional (full wave) methods. The synthetic radargrams can easily be compared to actual measured data.</p> <p>The research on WISDOM is supported by funding from the Centre National d’Etudes Spatiales (CNES) and the Deutsches Zentrum für Luft- und Raumfahrt (DLR).</p> <p>[1] V. Ciarletti, C. Corbel, D. Plettemeier, P. Cais, S. M. Clifford, S.-E. Hamran, "WISDOM GPR Designed for Shallow and High-Resolution Sounding of the Martian Subsurface", Proceedings of the IEEE, Vol. 99, Issue 5, pp. 824-836, May 2011. <br />[2] V. Ciarletti, S. Clifford, D. Plettemeier and the WISDOM Team, "The WISDOM Radar: Unveiling the Sub surface Beneath the ExoMars Rover and Identifying the Best Locations for Drilling", Astrobiology, Vol. 17, No. 6-7, July 2017 <br />[3] D. Plettemeier et al., "Full polarimetric GPR antenna system aboard the ExoMars rover," 2009 IEEE Radar Conference, Pasadena, CA, 2009, pp. 1-6, doi: 10.1109/RADAR.2009.4977120.<br />[4] C. Statz and D. Plettemeier, "BETSi: An electromagnetic time-domain simulation tool for antennas and heterogeneous media in ground penetration radar and biomedical applications," 2017 Computing and Electromagnetics International Workshop (CEM), Barcelona, 2017, pp. 37-38, doi: 10.1109/CEM.2017.7991875.</p>


2011 ◽  
Vol 317-319 ◽  
pp. 1631-1634
Author(s):  
Zhen Wan ◽  
Feng Cui ◽  
Yun Kui Zhang ◽  
Wu Liu ◽  
Wen Yuan Chen ◽  
...  

A six-axis Micromachined Electrostatically Suspended Accelerometer (MESA) which is based on LIGA-type microfabrication was designed. MESA employs a levitated perforated plate as its proof mass. Three main purposes are considered for the design of the perforated proof mass: (1) reducing squeeze-film effect; (2) improving the dynamic response of MESA; (3) facilitating the etching of sacrificial layer under the plate. This paper utilized a finite element model for evaluating air squeeze film damping effect of perforated proof mass. Among several designs of perforated proof mass, the best choice was found. Besides, a system-level model created in CoventorWare is used to evaluate the effect of squeeze film damping and the dynamic response of the MESA.


Electronics ◽  
2021 ◽  
Vol 10 (3) ◽  
pp. 231
Author(s):  
Chester Sungchung Park ◽  
Sunwoo Kim ◽  
Jooho Wang ◽  
Sungkyung Park

A digital front-end decimation chain based on both Farrow interpolator for fractional sample-rate conversion and a digital mixer is proposed in order to comply with the long-term evolution standards in radio receivers with ten frequency modes. Design requirement specifications with adjacent channel selectivity, inband blockers, and narrowband blockers are all satisfied so that the proposed digital front-end is 3GPP-compliant. Furthermore, the proposed digital front-end addresses carrier aggregation in the standards via appropriate frequency translations. The digital front-end has a cascaded integrator comb filter prior to Farrow interpolator and also has a per-carrier carrier aggregation filter and channel selection filter following the digital mixer. A Farrow interpolator with an integrate-and-dump circuitry controlled by a condition signal is proposed and also a digital mixer with periodic reset to prevent phase error accumulation is proposed. From the standpoint of design methodology, three models are all developed for the overall digital front-end, namely, functional models, cycle-accurate models, and bit-accurate models. Performance is verified by means of the cycle-accurate model and subsequently, by means of a special C++ class, the bitwidths are minimized in a methodic manner for area minimization. For system-level performance verification, the orthogonal frequency division multiplexing receiver is also modeled. The critical path delay of each building block is analyzed and the spectral-domain view is obtained for each building block of the digital front-end circuitry. The proposed digital front-end circuitry is simulated, designed, and both synthesized in a 180 nm CMOS application-specific integrated circuit technology and implemented in the Xilinx XC6VLX550T field-programmable gate array (Xilinx, San Jose, CA, USA).


Electronics ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 644
Author(s):  
Michal Frivaldsky ◽  
Jan Morgos ◽  
Michal Prazenica ◽  
Kristian Takacs

In this paper, we describe a procedure for designing an accurate simulation model using a price-wised linear approach referred to as the power semiconductor converters of a DC microgrid concept. Initially, the selection of topologies of individual power stage blocs are identified. Due to the requirements for verifying the accuracy of the simulation model, physical samples of power converters are realized with a power ratio of 1:10. The focus was on optimization of operational parameters such as real-time behavior (variable waveforms within a time domain), efficiency, and the voltage/current ripples. The approach was compared to real-time operation and efficiency performance was evaluated showing the accuracy and suitability of the presented approach. The results show the potential for developing complex smart grid simulation models, with a high level of accuracy, and thus the possibility to investigate various operational scenarios and the impact of power converter characteristics on the performance of a smart gird. Two possible operational scenarios of the proposed smart grid concept are evaluated and demonstrate that an accurate hardware-in-the-loop (HIL) system can be designed.


2021 ◽  
Vol 18 (4) ◽  
pp. 1-27
Author(s):  
Yasir Mahmood Qureshi ◽  
William Andrew Simon ◽  
Marina Zapater ◽  
Katzalin Olcoz ◽  
David Atienza

The increasing adoption of smart systems in our daily life has led to the development of new applications with varying performance and energy constraints, and suitable computing architectures need to be developed for these new applications. In this article, we present gem5-X, a system-level simulation framework, based on gem-5, for architectural exploration of heterogeneous many-core systems. To demonstrate the capabilities of gem5-X, real-time video analytics is used as a case-study. It is composed of two kernels, namely, video encoding and image classification using convolutional neural networks (CNNs). First, we explore through gem5-X the benefits of latest 3D high bandwidth memory (HBM2) in different architectural configurations. Then, using a two-step exploration methodology, we develop a new optimized clustered-heterogeneous architecture with HBM2 in gem5-X for video analytics application. In this proposed clustered-heterogeneous architecture, ARMv8 in-order cluster with in-cache computing engine executes the video encoding kernel, giving 20% performance and 54% energy benefits compared to baseline ARM in-order and Out-of-Order systems, respectively. Furthermore, thanks to gem5-X, we conclude that ARM Out-of-Order clusters with HBM2 are the best choice to run visual recognition using CNNs, as they outperform DDR4-based system by up to 30% both in terms of performance and energy savings.


Sign in / Sign up

Export Citation Format

Share Document