Modeling and Control of a High Pressure Combined Air/Fuel Injection System

2009 ◽  
Author(s):  
Chao Yong ◽  
Eric J. Barth
Keyword(s):  
High Pressure ◽  
Fuel Injection ◽  
Lumped Parameter Model ◽  
Injection System ◽  
Fuel Injection System ◽  
Modeling And Control ◽  
Lumped Parameter ◽  
Mass Flow Rates ◽  
And Control ◽  
Liquid Piston

A high pressure combined air-fuel injection system is designed and tested for an experimental free liquid-piston engine compressor. The application discussed utilizes available high pressure air from the compressor’s reservoir, and high pressure fuel to mix and then inject into a combustion chamber. This paper addresses the modeling, design and control for this particular high-pressure air-fuel injection system, which features an electronically controlled air/fuel ratio control scheme. This system consists of a fuel line and an air line, whose mass flow rates are restricted by metering valves. These two lines are connected to a common downstream tube where air and fuel are mixed. By controlling the upstream pressures and the orifice areas of the metering valves, desired A/F ratios can be achieved. The effectiveness of the proposed system is demonstrated by a lumped-parameter model in simulation and validated by experiments.

Numerical Simulation of the Dynamic Response of a Diesel Fuel Injector Using CFD

2005 ◽  
Author(s):  
Yong Yi ◽  
Aleksandra Egelja ◽  
Clement J. Sung
Keyword(s):  
Experimental Data ◽  
High Pressure ◽  
Dynamic Response ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection System ◽  
Fuel Injection System ◽  
Fuel Injector ◽  
Diesel Fuel Injection ◽  
Very High

The development of a very high pressure diesel fuel injection system has been one of the key solutions to improve engine performance and to reduce emissions. The diesel fuel management in the injector directly affects how the fuel spray is delivered to the combustion chamber, and therefore affects the mixing, combustion and the pollutants formation. To design such a very high pressure diesel fuel injection system, an advanced CFD tool to predict the complex flow in the fuel injection system is required in the robust design process. In this paper, a novel 3D CFD dynamic mesh with cavitation model is developed to simulate the dynamic response of the needle motion of a diesel fuel injector corresponding to high common rail pressure and other dimensional design variables, coupling with the imbalance of the spring force and the flow force (pressure plus viscous force). A mixture model is used for cavitation resulting from high speed flow in fuel injector. Due to the lack of experimental data, the model presented in this paper is only validated by a limited set of experimental data. Required meshing strategy is also discussed in the paper.

scholarly journals EFFECT OF ETHANOL ON PERFORMANCE AND DURABILITY OF A DIESEL COMMON RAIL HIGH PRESSURE FUEL PUMP

Transport ◽  
2015 ◽  
Vol 31 (3) ◽  
pp. 305-311 ◽  
Author(s):  
Tomas Mickevičius ◽  
Stasys Slavinskas ◽  
Raimondas Kreivaitis
Keyword(s):  
High Pressure ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Common Rail ◽  
Injection System ◽  
Fuel Injection System ◽  
Fuel Blend ◽  
High Pressure Pump ◽  
Fuel Pump ◽  
Fuel Delivery

This paper presents a comparative experimental study for determining the effect of ethanol on functionality of a high pressure pump of the common rail fuel injection system. For experimental durability tests were prepared two identical fuel injection systems, which were mounted on a test bed for a fuel injection pump. One of the fuel injection systems was feed with diesel fuel; other fuel injection system was fuelled with ethanol–diesel fuel blend. A blend with 12% v/v ethanol and 88% v/v diesel fuel and low sulphur diesel fuel as a reference fuel were used in this study. To determine the effect of ethanol on the durability of the high pressure pump total fuel delivery performance and surface roughness of pump element were measured prior and after the test. Results show that the use of the ethanol–diesel blend tested produced a negative effect on the durability of the high pressure fuel pump. The wear of plungers and barrels when using ethanol–diesel fuel blend caused a decrease in fuel delivery up to 30% after 100 h of operation.

Modal Analysis of Fuel Injection Systems and the Determination of a Transfer Function Between Rail Pressure and Injection Rate

2018 ◽  
Vol 140 (11) ◽  
Author(s):  
A. Ferrari ◽  
F. Paolicelli
Keyword(s):  
High Pressure ◽  
Transfer Function ◽  
Modal Analysis ◽  
Flow Rate ◽  
Fuel Injection ◽  
Injection System ◽  
Rail Pressure ◽  
Hydraulic Circuit ◽  
Lumped Parameter ◽  
Injection Apparatus

A detailed analysis of a common rail (CR) fuel injection system, equipped with solenoid injectors for Euro 6 diesel engine applications, has been performed in the frequency domain. A lumped parameter numerical model of the high-pressure hydraulic circuit, from the pump delivery to the injector nozzle, has been realized. The model outcomes have been validated through a comparison with frequency values that were obtained by applying the peak-picking technique to the experimental pressure time histories acquired from the pipe that connects the injector to the rail. The eigenvectors associated with the different eigenfrequencies have been calculated and physically interpreted, thus providing a methodology for the modal analysis of hydraulic systems. Three main modal motions have been identified in the considered fuel injection apparatus, and the possible resonances with the external forcing terms, i.e., pump delivered flow rate, injected flow rate, and injector dynamic fuel leakage through the pilot valve, have been discussed. The investigation has shown that the rail is mainly involved in the first two vibration modes. In the first mode, the rail performs a decoupling action between the high-pressure pump and the downstream hydraulic circuit. Consequently, the oscillations generated by the pump flow rates mainly remain confined to the pipe between the pump and the rail. The second mode is centered on the rail and involves a large part of the hydraulic circuit, both upstream and downstream of the rail. Finally, the third mode principally affects the injector and its internal hydraulic circuit. It has also been observed that some geometric features of the injection apparatus can have a significant effect on the system dynamics and can induce hydraulic resonance phenomena. Furthermore, the lumped parameter model has been used to determine a simplified transfer function between rail pressure and injected flow rate. The knowledge obtained from this study can help to guide designers draw up an improved design of this kind of apparatus, because the pressure waves, which are triggered by impulsive events and are typical of injector working, can affect the performance of modern injection systems, especially when digital rate shaping strategies or closely coupled multiple injections are implemented.

Sign in / Sign up

Export Citation Format

Share Document