Fourier Decomposed Turbulence Measurements Downstream of a High-Pressure Turbine Stage

2008 ◽  
Author(s):  
Lars-Uno Axelsson ◽  
William K. George ◽  
T. Gunnar Johansson
Keyword(s):  
High Pressure ◽  
Periodic Component ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Time Resolved ◽  
Velocity Fluctuations ◽  
Axial Turbine ◽  
Blade Passage ◽  
Turbulence Measurements ◽  
Time Resolved Measurements

This forum paper discusses phase-resolved turbulence measurements of the flow downstream of an axial turbine, and especially how phase-resolved measurements compare to time-resolved measurements. The time-resolved spectra produced higher velocity fluctuations than the corresponding phase-resolved spectra even when the periodic component was filtered out from the time-resolved measurements. The phase-resolved spectrum effectively removes all the peaks in the spectrum except for the ones associated with the blade-passage frequency.

Comparison of Steady and Unsteady Coupled Heat-Transfer Simulations of a High-Pressure Turbine Blade

2015 ◽  
Author(s):  
Markus Schmidt ◽  
Christoph Starke
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Steady State ◽  
Flow Field ◽  
Film Cooling ◽  
Strong Increase ◽  
Pressure Side ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Time Resolved

This article presents results for the coupled simulation of a high-pressure turbine stage in consideration of unsteady hot gas flows. A semi-unsteady coupling process was developed to solve the conjugate heat transfer problem for turbine components of gas turbines. Time-resolved CFD simulations are coupled to a finite element solver for the steady state heat conduction inside of the blade material. A simplified turbine stage geometry is investigated in this paper to describe the influence of the unsteady flow field onto the time-averaged heat transfer. Comparisons of the time-resolved results to steady state results indicate the importance of a coupled simulation and the consideration of the time-dependent flow-field. Different film-cooling configurations for the turbine NGV are considered, resulting in different temperature and pressure deficits in the vane wake. Their contribution to non-linear effects causing the time-averaged heat load to differ from a steady result is discussed to further highlight the necessity of unsteady design methods for future turbine developments. A strong increase in the pressure side heat transfer coefficients for unsteady simulations is observed in all results. For higher film-cooling mass flows in the upstream row, the preferential migration of hot fluid towards the pressure side of a turbine blade is amplified as well, which leads to a strong increase in material temperature at the pressure side and also in the blade tip region.

Time-Resolved Vane-Rotor Interaction in a High-Pressure Turbine Stage

2003 ◽  
Vol 125 (1) ◽  
pp. 1-13 ◽  
Author(s):  
R. J. Miller ◽  
R. W. Moss ◽  
R. W. Ainsworth ◽  
C. K. Horwood
Keyword(s):  
High Pressure ◽  
Secondary Flow ◽  
Time Varying ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Trailing Edge ◽  
Time Resolved ◽  
Periodic Fluctuation ◽  
Interaction Mechanisms ◽  
Numerical Predictions

This paper describes the time-varying aerodynamic interaction mechanisms that have been observed within a transonic high-pressure turbine stage; these are inferred from the time-resolved behavior of the rotor exit flow field. It contains results both from an experimental program in a turbine test facility and from numerical predictions. Experimental data was acquired using a fast-response aerodynamic probe capable of measuring Mach number, whirl angle, pitch angle, total pressure, and static pressure. A 3-D time-unsteady viscous Navier-Stokes solver was used for the numerical predictions. The unsteady rotor exit flowfield is formed from a combination of four flow phenomena: the rotor wake, the rotor trailing edge recompression shock, the tip-leakage flow, and the hub secondary flow. This paper describes the time-resolved behavior of each phenomenon and discusses the interaction mechanisms from which each originates. Two significant vane periodic changes (equivalent to a time-varying flow in the frame of reference of the rotor) in the rotor exit flowfield are identified. The first is a severe vane periodic fluctuation in flow conditions close to the hub wall and the second is a smaller vane periodic fluctuation occurring at equal strength over the entire blade span. These two regions of periodically varying flow are shown to be caused by two groups of interaction mechanisms. The first is thought to be caused by the interaction between the wake and secondary flow of the vane with the downstream rotor; and the second is thought to be caused by a combination of the interaction of the vane trailing edge recompression shock with the rotor, and the interaction between the vane and rotor potential fields.

Computational and Experimental Study of the Unsteady Convection of Entropy Waves Within a High Pressure Turbine Stage

2020 ◽  
Author(s):  
Lorenzo Pinelli ◽  
Michele Marconcini ◽  
Roberto Pacciani ◽  
Paolo Gaetani ◽  
Giacomo Persico
Keyword(s):  
High Pressure ◽  
High Speed ◽  
Low Frequency ◽  
Frequency Content ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Cfd Simulations ◽  
Time Resolved ◽  
Azimuthal Position ◽  
Cfd Method

Abstract This paper describes the transport and the interaction of pulsating entropy waves generated by combustor burners within a high pressure turbine stage for aeronautical application. Experiments and Computational Fluid Dynamics (CFD) simulations were carried out in the context of the European Research Project RECORD. Experimental campaigns considering burner-representative temperature fluctuations (in terms of spot shape, fluctuation frequency and total temperature variation percentage) injected upstream of an un-cooled high-pressure gas turbine stage have been performed in the high-speed closed-loop test-rig of the Fluid Machine Laboratory (LFM) of Politecnico di Milano (Italy). The pulsating entropy waves are injected at the stage inlet in streamwise direction at four different azimuthal positions featuring a 7% over-temperature with respect to the main flow with a frequency of 90 Hz. Detailed time-resolved temperature measurements (in the range of 0–200 Hz) upstream and downstream of the stage, as well as in the stator–rotor axial gap were performed. Time-accurate CFD simulations with and without entropy fluctuations imposed at the stage inlet were performed with the TRAF code, developed by the University of Florence. A numerical post-processing procedure, based on the DFT (Discrete Fourier Transform) of the conservative variables has been implemented to extract the low frequency content connected to the entropy fluctuations. Measurements highlighted a significant attenuation of the entropy wave spot throughout their transport within the stator channel and their interaction with the rotor blade rows, highly depending on their injection azimuthal position. Simulations show an overall good agreement with the experiments on the measurement traverses, especially at the stage outlet. By exploiting the combination of experiments and simulations, the aerodynamic and thermal implications of the temperature fluctuation injected upstream of the stage were properly assessed, thus allowing suggest useful information to the designer. The comparison with the experiments confirms the accuracy of the CFD method to solve the periodic, but characterized by a low frequency content event, associated with the entropy wave fluctuation.

Using CFD to Reduce Resonant Stresses on a Single-Stage, High-Pressure Turbine Blade

2002 ◽  
Author(s):  
J. P. Clark ◽  
A. S. Aggarwala ◽  
M. A. Velonis ◽  
R. E. Gacek ◽  
S. S. Magge ◽  
...  
Keyword(s):  
High Pressure ◽  
Turbine Blade ◽  
Guide Vane ◽  
Turbine Blades ◽  
Suction Side ◽  
Lessons Learned ◽  
Single Stage ◽  
Navier Stokes ◽  
High Pressure Turbine ◽  
Time Resolved

The ability to predict levels of unsteady forcing on high-pressure turbine blades is critical to avoid high-cycle fatigue failures. In this study, 3D time-resolved computational fluid dynamics is used within the design cycle to predict accurately the levels of unsteady forcing on a single-stage high-pressure turbine blade. Further, nozzle-guide-vane geometry changes including asymmetric circumferential spacing and suction-side modification are considered and rigorously analyzed to reduce levels of unsteady blade forcing. The latter is ultimately implemented in a development engine, and it is shown successfully to reduce resonant stresses on the blade. This investigation builds upon data that was recently obtained in a full-scale, transonic turbine rig to validate a Reynolds-Averaged Navier-Stokes (RANS) flow solver for the prediction of both the magnitude and phase of unsteady forcing in a single-stage HPT and the lessons learned in that study.

Experimental Investigation of Vane Clocking in a One and 1/2 Stage High Pressure Turbine

2004 ◽  
Author(s):  
Charles W. Haldeman ◽  
Michael G. Dunn ◽  
John W. Barter ◽  
Brian R. Green ◽  
Robert F. Bergholz
Keyword(s):  
High Pressure ◽  
Low Pressure ◽  
Test Facility ◽  
Maximum Efficiency ◽  
High Pressure Turbine ◽  
Data Set ◽  
Time Resolved ◽  
Low Pressure Turbine ◽  
Turbine Vane ◽  
Vane Clocking

Aerodynamic measurements were acquired on a modern single-stage, transonic, high-pressure turbine with the adjacent low-pressure turbine vane row (a typical civilian one and one-half stage turbine rig) to observe the effects of low-pressure turbine vane clocking on overall turbine performance. The turbine rig (loosely referred to in this paper as the stage) was operated at design corrected conditions using the Ohio State University Gas Turbine Laboratory Turbine Test Facility (TTF). The research program utilized uncooled hardware in which all three airfoils were heavily instrumented at multiple spans to develop a full clocking dataset. The low-pressure turbine vane row (LPTV) was clocked relative to the high-pressure turbine vane row (HPTV). Various methods were used to evaluate the influence of clocking on the aeroperformance (efficiency) and the aerodynamics (pressure loading) of the LPTV, including time-resolved and time-averaged measurements. A change in overall efficiency of approximately 2–3% due to clocking effects is demonstrated and could be observed using a variety of independent methods. Maximum efficiency is obtained when the time-average surface pressures are highest on the LPTV and the time-resolved surface pressure (both in the time domain and frequency domain) show the least amount of variation. The overall effect is obtained by integrating over the entire airfoil, as the three-dimensional effects on the LPTV surface are significant. This experimental data set validates several computational research efforts that suggested wake migration is the primary reason for the perceived effectiveness of vane clocking. The suggestion that wake migration is the dominate mechanism in generating the clocking effect is also consistent with anecdotal evidence that fully cooled engine rigs do not see a great deal of clocking effect. This is consistent since the additional disturbances induced by the cooling flows and/or the combustor make it extremely difficult to find an alignment for the LPTV given the strong 3D nature of modern high-pressure turbine flows.

Assessment of the Indirect Combustion Noise Generated in a Transonic High-Pressure Turbine Stage

2015 ◽  
Author(s):  
Dimitrios Papadogiannis ◽  
Florent Duchaine ◽  
Laurent Gicquel ◽  
Gaofeng Wang ◽  
Stéphane Moreau ◽  
...  
Keyword(s):  
High Pressure ◽  
Acoustic Waves ◽  
Gas Turbines ◽  
Guide Vane ◽  
Combustion Noise ◽  
Dynamic Mode Decomposition ◽  
Dynamic Mode ◽  
Noise Generation ◽  
Turbine Stage ◽  
High Pressure Turbine

Indirect combustion noise, generated by the acceleration and distortion of entropy waves through the turbine stages, has been shown to be the dominant noise source of gas turbines at low-frequencies and to impact the thermoacoustic behavior of the combustor. In the present work, indirect combustion noise generation is evaluated in the realistic, fully 3D transonic high-pressure turbine stage MT1 using Large-Eddy Simulations (LES). An analysis of the basic flow and the different turbine noise generation mechanisms is performed for two configurations: one with a steady inflow and a second with a pulsed inlet, where a plane entropy wave train at a given frequency is injected before propagating across the stage generating indirect noise. The noise is evaluated through the Dynamic Mode Decomposition of the flow field. It is compared with previous 2D simulations of a similar stator/rotor configuration, as well as with the compact theory of Cumpsty and Marble. Results show that the upstream propagating entropy noise is reduced due to the choked turbine nozzle guide vane. Downstream acoustic waves are found to be of similar strength to the 2D case, highlighting the potential impact of indirect combustion noise on the overall noise signature of the engine.

Three Dimensional Heat Transfer Analysis of High Pressure Turbine Blade

2009 ◽  
Author(s):  
A. Sipatov ◽  
L. Gomzikov ◽  
V. Latyshev ◽  
N. Gladysheva
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
High Pressure ◽  
Rotor Blade ◽  
Computational Analysis ◽  
Three Dimensional ◽  
Heat Transfer Analysis ◽  
Aircraft Engines ◽  
Turbine Stage ◽  
High Pressure Turbine

The present tendency of creating new aircraft engines with a higher level of fuel efficiency leads to the necessity to increase gas temperature at a high pressure turbine (HPT) inlet. To design such type of engines, the improvement of accuracy of the computational analysis is required. According to this the numerical analysis methods are constantly developing worldwide. The leading firms in designing aircraft engines carry out investigations in this field. However, this problem has not been resolved completely yet because there are many different factors affecting HPT blade heat conditions. In addition in some cases the numerical methods and approaches require tuning (for example to predict laminar-turbulent transition region or to describe the interaction of boundary layer and shock wave). In this work our advanced approach of blade heat condition numerical estimation based on the three-dimensional computational analysis is presented. The object of investigation is an advanced aircraft engine HPT first stage blade. The given analysis consists of two interrelated parts. The first part is a stator-rotor interaction modeling of the investigated turbine stage (unsteady approach). Solving this task we devoted much attention to modeling unsteady effects of stator-rotor interaction and to describing an influence of applied inlet boundary conditions on the blade heat conditions. In particular, to determine the total pressure, flow angle and total temperature distributions at the stage inlet we performed a numerical modeling of the combustor chamber of the investigated engine. The second part is a flow modeling in the turbine stage using flow parameters averaging on the stator-rotor interface (steady approach). Here we used sufficiently finer grid discretization to model all perforation holes on the stator vane and rotor blade, endwalls films in detail and to apply conjugate heat transfer approach for the rotor blade. Final results were obtained applying the results of steady and unsteady approaches. Experimental data of the investigated blade heat conditions are presented in the paper. These data were obtained during full size experimental testing the core of the engine and were collected using two different type of experimental equipment: thermocouples and thermo-crystals. The comparison of experimental data and final results meets the requirements of our investigation.

scholarly journals Calculation and Correlation of the Unsteady Flowfield in a High Pressure Turbine

2002 ◽  
Author(s):  
Milind A. Bakhle ◽  
Jong S. Liu ◽  
Josef Panovsky ◽  
Theo G. Keith ◽  
Oral Mehmed
Keyword(s):  
High Pressure ◽  
Three Dimensional ◽  
Unsteady Aerodynamics ◽  
Forced Vibrations ◽  
Forced Response ◽  
Operating Conditions ◽  
Test Facility ◽  
Navier Stokes ◽  
Turbine Stage ◽  
High Pressure Turbine

Forced vibrations in turbomachinery components can cause blades to crack or fail due to high-cycle fatigue. Such forced response problems will become more pronounced in newer engines with higher pressure ratios and smaller axial gap between blade rows. An accurate numerical prediction of the unsteady aerodynamics phenomena that cause resonant forced vibrations is increasingly important to designers. Validation of the computational fluid dynamics (CFD) codes used to model the unsteady aerodynamic excitations is necessary before these codes can be used with confidence. Recently published benchmark data, including unsteady pressures and vibratory strains, for a high-pressure turbine stage makes such code validation possible. In the present work, a three dimensional, unsteady, multi blade-row, Reynolds-Averaged Navier Stokes code is applied to a turbine stage that was recently tested in a short duration test facility. Two configurations with three operating conditions corresponding to modes 2, 3, and 4 crossings on the Campbell diagram are analyzed. Unsteady pressures on the rotor surface are compared with data.

Sign in / Sign up

Export Citation Format

Share Document