Influence of the Swirler Design on the Flame Transfer Function of Premixed Flames

2005 ◽  
Author(s):  
C. Hirsch ◽  
D. Fanaca ◽  
P. Reddy ◽  
W. Polifke ◽  
T. Sattelmayer
Keyword(s):  
Transfer Function ◽  
Transfer Functions ◽  
Premixed Flames ◽  
Swirl Number ◽  
Burner Exit ◽  
Novel Approach ◽  
Swirling Flames ◽  
Simplified Analysis ◽  
Vorticity Transport ◽  
Good Agreement

A novel approach to the description of flame transfer functions of premixed swirling flames is presented based on a simplified analysis of the vorticity transport equation. With this model it is possible to reproduce transfer function amplitude in excess of unity observed for swirling flames as well as to explain the differences seen in flame transfer functions for different swirler types. Measurements of flame transfer functions were performed on perfectly premixed flames generated by an axial and a radial swirler with an annular exit. Flames were adjusted as to achieve respective dynamic similarity. The comparison of the flame transfer functions shows the influence of the swirler type. Good agreement with the model validates the theoretical approach and allows to attribute the specific differences seen between the two swirler types with the generation of a swirl number modulation induced by the convective time delay between radial swirler and burner exit. The model also allows to explain the change of flame transfer function amplitude with pre-heating observed in previous publications.

scholarly journals Effects of the Injector Design on the Transfer Function of Premixed Swirling Flames

2017 ◽  
Author(s):  
M. Gatti ◽  
R. Gaudron ◽  
C. Mirat ◽  
T. Schuller
Keyword(s):  
Transfer Function ◽  
Heat Release ◽  
Heat Release Rate ◽  
Release Rate ◽  
Bluff Body ◽  
Transfer Functions ◽  
Thermal Power ◽  
Phase Lag ◽  
Swirl Number ◽  
Injector Design

This article reports a series of experiments on the dynamics of lean-premixed swirl-stabilized flames submitted to harmonic flowrate modulations. The flame transfer function is analyzed for different injector designs with a specific focus on conditions leading to the lowest heat release rate response for a given flowrate perturbation. Experiments are carried out at a fixed equivalence ratio and fixed thermal power. Transfer functions are measured for radial swirling vanes by modifying the diameter of the swirler injection holes, the diameter of the injection tube at the top of the swirler and the end piece diameter of a central insert serving as a bluff body. It is found that the lowest response depends on the forcing frequency and is obtained when the injector design features the largest swirl number. The transfer function of the studied flames features a minimum gain value which decreases for increasing swirl levels. This minimum value is found to be independent of the velocity forcing level and is only controlled by the level of swirl. An excessive swirl level however leads to flash-back of the perturbed flames inside the injector. The way the flame behaves at this forcing frequency is analyzed for a set of injectors featuring the same radial swirling vane design and different injection tube diameters or conical end pieces. It is found that at the condition corresponding to the lowest FTF gain, i.e. the injector with the largest swirl number, the upper and lower parts of the flame contribute to out of phase heat release oscillations, but they also both feature a reduced level of fluctuations. When the swirl number decreases, the FTF gain increases due to a reduction of the phase lag between heat release rate oscillations in the lower and the upper parts of the flame and more importantly due to a general increase of the level of heat release oscillations in both parts of the flame.

Impact of Shear Flow Instabilities on the Magnitude and Saturation of the Flame Response

2014 ◽  
Vol 136 (7) ◽  
Author(s):  
Steffen Terhaar ◽  
Bernhard Ćosić ◽  
Christian Oliver Paschereit ◽  
Kilian Oberleithner
Keyword(s):  
Transfer Function ◽  
Shear Flow ◽  
High Speed ◽  
Transfer Functions ◽  
Flow Fields ◽  
Shear Layers ◽  
Flow Instabilities ◽  
Mean Flow ◽  
Swirl Number ◽  
Flame Response

Amplitude-dependent flame transfer functions, also denoted as flame describing functions, are valuable tools for the prediction of limit-cycle amplitudes of thermoacoustic instabilities. However, the effects that govern the transfer function magnitude at low and high amplitudes are not yet fully understood. It is shown in the present work that the flame response at perfectly premixed conditions is strongly influenced by the growth rate of vortical structures in the shear layers. An experimental study in a generic swirl-stabilized combustor was conducted in order to measure the amplitude-dependent flame transfer function and the corresponding flow fields subjected to acoustic forcing. The applied measurement techniques included the multi-microphone-method, high-speed OH*-chemiluminescence measurements, and high-speed particle image velocimetry. The flame response and the corresponding flow fields are assessed for three different swirl numbers at 196 Hz forcing frequency. The results show that forcing leads to significant changes in the time-averaged reacting flow fields and flame shapes. A triple decomposition is applied to the time-resolved data, which reveals that coherent velocity fluctuations at the forcing frequency are amplified considerably stronger in the shear layers at low forcing amplitudes than at high amplitudes, which is an indicator for a nonlinear saturation process. The strongest saturation is found for the lowest swirl number, where the forcing additionally detached the flame. For the highest swirl number, the saturation of the vortex amplitude is weaker. Overall, the amplitude-dependent vortex amplification resembles the characteristics of the flame response very well. An application of a linear stability analysis to the time-averaged flow fields at increasing forcing amplitudes yields the decreasing growth rates of shear flow instabilities at the forcing frequency. It therefore successfully predicts a saturation at high forcing amplitudes and demonstrates that the mean flow field and its modifications are of utmost importance for the growth of vortices in the shear layers. Moreover, the results clearly show that the amplification of vortices in the shear layers is an important driver for heat release fluctuations and their saturation.

Impact of Shear Flow Instabilities on the Magnitude and Saturation of the Flame Response

2013 ◽  
Author(s):  
Steffen Terhaar ◽  
Bernhard Ćosić ◽  
Christian Oliver Paschereit ◽  
Kilian Oberleithner
Keyword(s):  
Transfer Function ◽  
Shear Flow ◽  
High Speed ◽  
Transfer Functions ◽  
Flow Fields ◽  
Shear Layers ◽  
Flow Instabilities ◽  
Mean Flow ◽  
Swirl Number ◽  
Flame Response

Amplitude-dependent flame transfer functions, also denoted as flame describing functions, are valuable tools for the prediction of limit-cycle amplitudes of thermoacoustic instabilities. However, the effects that govern the transfer function magnitude at low and high amplitudes are not yet fully understood. It is shown in the present work that the flame response at perfectly premixed conditions is dominated by the growth rate of vortical structures in the shear layers. An experimental study in a generic swirl-stabilized combustor was conducted in order to measure the amplitude-dependent flame transfer function and the corresponding flow fields subjected to acoustic forcing. The applied measurement techniques included the Multi-Microphone-Method, high-speed OH*-chemiluminescence measurements, and high-speed Particle Image Velocimetry. The flame response and the corresponding flow fields are assessed for three different swirl numbers at 196 Hz forcing frequency. The results show that forcing leads to significant changes in the time-averaged reacting flow fields and flame shapes. A triple decomposition is applied to the time-resolved data, which reveals that coherent velocity fluctuations at the forcing frequency are amplified considerably stronger in the shear layers at low forcing amplitudes than at high amplitudes, an indicator for a nonlinear saturation process. The strongest saturation is found for the lowest swirl number, where the forcing additionally detached the flame. For the highest swirl number, the saturation of the vortex amplitude is weaker. Overall, the amplitude-dependent vortex amplification resembles the characteristics of the flame response very well. An application of linear stability analysis to the time-averaged flow fields at increasing forcing amplitudes yields decreasing growth rates of shear flow instabilities at the forcing frequency. It therefore successfully predicts a saturation at high forcing amplitudes and demonstrates that the mean flow field and its modifications are of utmost importance for the growth of vortices in the shear layers. Moreover, the results clearly show that the amplification of vortices in the shear layers is a dominant driver for heat release fluctuations and their saturation.

scholarly journals The spatiotemporal transfer function of the Limulus lateral eye.

1978 ◽  
Vol 72 (2) ◽  
pp. 167-202 ◽  
Author(s):  
S E Brodie ◽  
B W Knight ◽  
F Ratliff
Keyword(s):  
Transfer Function ◽  
Transfer Functions ◽  
Data Transfer ◽  
Laboratory Measurements ◽  
Estimation Of Parameters ◽  
Generator Potential ◽  
Physiological Processes ◽  
Lateral Eye ◽  
Sinusoidal Gratings ◽  
Good Agreement

The dynamics of the Limulus retina may be well described by the spatiotemporal transfer function, which measures the response of the eye to moving sinusoidal gratings. We consider a model for this system, which incorporates an excitatory generator potential, and self- and lateral inhibitory processes. Procedures are described which allow estimation of parameters for the model consistent with the empirical transfer function data. Transfer functions calculated from the model show good agreement with laboratory measurements, and may be used to predict accurately the response of the eye to arbitrary moving stimuli. The model allows convenient interpretation of the transfer function measurements in terms of physiological processes which underly the response of the Limulus retina.

Analytic integration of contrast transfer functions

1988 ◽  
Vol 46 ◽  
pp. 822-823
Author(s):  
Peter Rez
Keyword(s):  
Wave Function ◽  
Transfer Function ◽  
Transfer Functions ◽  
Spherical Aberration ◽  
Continuous Distribution ◽  
Objective Lens ◽  
Direction Parallel ◽  
Scattering Angle ◽  
Analytic Integration ◽  
Image Position

In high resolution microscopy the image amplitude is given by the convolution of the specimen exit surface wave function and the microscope objective lens transfer function. This is usually done by multiplying the wave function and the transfer function in reciprocal space and integrating over the effective aperture. For very thin specimens the scattering can be represented by a weak phase object and the amplitude observed in the image plane is1where fe (Θ) is the electron scattering factor, r is a postition variable, Θ a scattering angle and x(Θ) the lens transfer function. x(Θ) is given by2where Cs is the objective lens spherical aberration coefficient, the wavelength, and f the defocus.We shall consider one dimensional scattering that might arise from a cross sectional specimen containing disordered planes of a heavy element stacked in a regular sequence among planes of lighter elements. In a direction parallel to the disordered planes there will be a continuous distribution of scattering angle.

Trombone Transfer Functions: Comparison Between Frequency-Swept Sine Wave and Human Performer Input

2012 ◽  
Vol 37 (4) ◽  
pp. 447-454
Author(s):  
James W. Beauchamp
Keyword(s):  
Transfer Function ◽  
Transfer Functions ◽  
Cutoff Frequency ◽  
Sine Wave ◽  
Nonlinear Propagation ◽  
Linear Filter ◽  
Wave System ◽  
General Effect ◽  
Filter Characteristic ◽  
High Pass

Abstract Source/filter models have frequently been used to model sound production of the vocal apparatus and musical instruments. Beginning in 1968, in an effort to measure the transfer function (i.e., transmission response or filter characteristic) of a trombone while being played by expert musicians, sound pressure signals from the mouthpiece and the trombone bell output were recorded in an anechoic room and then subjected to harmonic spectrum analysis. Output/input ratios of the signals’ harmonic amplitudes plotted vs. harmonic frequency then became points on the trombone’s transfer function. The first such recordings were made on analog 1/4 inch stereo magnetic tape. In 2000 digital recordings of trombone mouthpiece and anechoic output signals were made that provide a more accurate measurement of the trombone filter characteristic. Results show that the filter is a high-pass type with a cutoff frequency around 1000 Hz. Whereas the characteristic below cutoff is quite stable, above cutoff it is extremely variable, depending on level. In addition, measurements made using a swept-sine-wave system in 1972 verified the high-pass behavior, but they also showed a series of resonances whose minima correspond to the harmonic frequencies which occur under performance conditions. For frequencies below cutoff the two types of measurements corresponded well, but above cutoff there was a considerable difference. The general effect is that output harmonics above cutoff are greater than would be expected from linear filter theory, and this effect becomes stronger as input pressure increases. In the 1990s and early 2000s this nonlinear effect was verified by theory and measurements which showed that nonlinear propagation takes place in the trombone, causing a wave steepening effect at high amplitudes, thus increasing the relative strengths of the upper harmonics.

Structural-parametric model of an electroelastic actuator for nanomechanics

2020 ◽  
pp. 3-11
Author(s):  
S.M. Afonin
Keyword(s):  
Transfer Function ◽  
Piezoelectric Actuator ◽  
Transfer Functions ◽  
Piezoelectric Effect ◽  
Parametric Model ◽  
Elastic Compliance ◽  
Parametric Models ◽  
Piezo Actuator ◽  
Structural Scheme ◽  
Model Transfer

Structural-parametric models, structural schemes are constructed and the transfer functions of electro-elastic actuators for nanomechanics are determined. The transfer functions of the piezoelectric actuator with the generalized piezoelectric effect are obtained. The changes in the elastic compliance and rigidity of the piezoactuator are determined taking into account the type of control. Keywords electro-elastic actuator, piezo actuator, structural-parametric model, transfer function, parametric structural scheme

Relationship of gain and phase in the transfer function of swirling flames

2020 ◽  
Author(s):  
Guoqing Wang ◽  
Jianyi Zheng ◽  
Lei Li ◽  
Xunchen Liu ◽  
Fei Qi
Keyword(s):  
Transfer Function ◽  
Swirling Flames ◽  
Relationship Of

scholarly journals Determination of the Optimal Neural Network Transfer Function for Response Surface Methodology and Robust Design

2021 ◽  
Vol 11 (15) ◽  
pp. 6768
Author(s):  
Tuan-Ho Le ◽  
Hyeonae Jang ◽  
Sangmun Shin
Keyword(s):  
Response Surface Methodology ◽  
Transfer Function ◽  
Response Surface ◽  
Robust Design ◽  
Transfer Functions ◽  
Desirability Function ◽  
Likelihood Estimation ◽  
Statistical Simulation ◽  
Screening Procedure ◽  
Function Estimation

Response surface methodology (RSM) has been widely recognized as an essential estimation tool in many robust design studies investigating the second-order polynomial functional relationship between the responses of interest and their associated input variables. However, there is scope for improvement in the flexibility of estimation models and the accuracy of their results. Although many NN-based estimations and optimization approaches have been reported in the literature, a closed functional form is not readily available. To address this limitation, a maximum-likelihood estimation approach for an NN-based response function estimation (NRFE) is used to obtain the functional forms of the process mean and standard deviation. While the estimation results of most existing NN-based approaches depend primarily on their transfer functions, this approach often requires a screening procedure for various transfer functions. In this study, the proposed NRFE identifies a new screening procedure to obtain the best transfer function in an NN structure using a desirability function family while determining its associated weight parameters. A statistical simulation was performed to evaluate the efficiency of the proposed NRFE method. In this particular simulation, the proposed NRFE method provided significantly better results than conventional RSM. Finally, a numerical example is used for validating the proposed method.

Sign in / Sign up

Export Citation Format

Share Document