Separation and Transition Control on an Aft-Loaded Ultra-High-Lift LP Turbine Blade at Low Reynolds Numbers: High-Speed Validation

2005 ◽  
Author(s):  
Maria Vera ◽  
Xue Feng Zhang ◽  
Howard Hodson ◽  
Neil Harvey
Keyword(s):  
Surface Roughness ◽  
Mach Number ◽  
Surface Finish ◽  
High Speed ◽  
Reynolds Numbers ◽  
High Lift ◽  
Low Reynolds Numbers ◽  
Low Speed ◽  
Transition Mechanism ◽  
Low Reynolds

This paper presents the second part of an investigation of the combined effects of unsteadiness and surface roughness on an aft-loaded ultra high lift low pressure turbine (LPT) profile at low Reynolds numbers. The investigation has been performed using low-speed and high-speed cascade facilities. The low speed and the high speed profiles have been designed to have the same normalized isentropic Mach number distribution. The low speed results have been presented in Part 1 of this paper. The current paper examines the effect of different surface finishes on an aft-loaded ultra-high-lift LPT profile at Mach and Reynolds numbers representative of LPT engine conditions. The surface roughness values are presented along with the profile losses under steady and unsteady inflow conditions. The results show that the use of a rough surface finish might reduce the profile loss. In addition, the results show that the same quantitative values of losses are obtained at high and low speed flow conditions. The latter proves the validity of the low speed approach for ultra high lift profiles for the case of an exit Mach number of the order of 0.64. Hot wire measurements were carried out to explain the effect of the surface finish on the wake induced transition mechanism.

Separation and Transition Control on an Aft-Loaded Ultra-High-Lift LP Turbine Blade at Low Reynolds Numbers: High-Speed Validation

2006 ◽  
Vol 129 (2) ◽  
pp. 340-347 ◽  
Author(s):  
Maria Vera ◽  
Xue Feng Zhang ◽  
Howard Hodson ◽  
Neil Harvey
Keyword(s):  
Surface Roughness ◽  
Mach Number ◽  
Surface Finish ◽  
High Speed ◽  
Reynolds Numbers ◽  
High Lift ◽  
Low Reynolds Numbers ◽  
Low Speed ◽  
Transition Mechanism ◽  
Low Reynolds

This paper presents the second part of an investigation of the combined effects of unsteadiness and surface roughness on an aft-loaded ultra-high-lift low-pressure turbine (LPT) profile at low Reynolds numbers. The investigation has been performed using low- and high-speed cascade facilities. The low- and high-speed profiles have been designed to have the same normalized isentropic Mach number distribution. The low-speed results have been presented in the first part (Zhang, Vera, Hodson, and Harvey, 2006, ASME J. Turbomach., 128, pp. 517–527). The current paper examines the effect of different surface finishes on an aft-loaded ultra-high-lift LPT profile at Mach and Reynolds numbers representative of LPT engine conditions. The surface roughness values are presented along with the profile losses under steady and unsteady inflow conditions. The results show that the use of a rough surface finish can be used to reduce the profile loss. In addition, the results show that the same quantitative values of losses are obtained at high- and low-speed flow conditions. The latter proves the validity of the low-speed approach for ultra-high-lift profiles for the case of an exit Mach number of the order of 0.64. Hot-wire measurements were carried out to explain the effect of the surface finish on the wake-induced transition mechanism.

Separation and Transition Control on an Aft-Loaded Ultra-High-Lift LP Turbine Blade at Low Reynolds Numbers: Low-Speed Investigation

2005 ◽  
Author(s):  
Xue Feng Zhang ◽  
Maria Vera ◽  
Howard Hodson ◽  
Neil Harvey
Keyword(s):  
Turbine Blade ◽  
Separation Bubble ◽  
Reynolds Numbers ◽  
Surface Boundary ◽  
Suction Surface ◽  
High Lift ◽  
Low Reynolds Numbers ◽  
Low Speed ◽  
Profile Losses ◽  
Low Reynolds

An experimental study was conducted to improve the performance of an aft-loaded ultra-high-lift low-pressure turbine blade known as U2 at low Reynolds numbers. This was achieved by manipulation of the laminar-turbulent transition process on the suction surface. The U2 profile was designed to meet the targets of reduced cost, weight and fuel burn of aircraft engines. The studies were conducted on both low-speed and high-speed experimental facilities under the unsteady flow conditions with upstream passing wakes. The current paper presents the low-speed investigation results. On the smooth suction surface, the incoming wakes are not strong enough to suppress the separation bubble due to the strong adverse pressure gradient on the suction surface and the low wake passing frequency, which allows the separation between the wakes more time to re-establish. Therefore, the profile losses of this ultra-high-lift blade are not as low as conventional or high-lift blades at low Reynolds numbers even in unsteady flows. Two different types of passive separation control devices, i.e. surface trips and air jets, were investigated to further improve the blade performance. The measurement results show that the profile losses can be further reduced to the levels similar to those of the high-lift and conventional blades due to the aft-loaded nature of this ultra-high-lift blade. Detailed surveys of the blade surface boundary layer developments showed that the loss reduction was due to the suppression of the separation underneath the wakes, the effect of the strengthened calmed region and the smaller separation bubble between wakes.

Separation and Transition Control on an Aft-Loaded Ultra-High-Lift LP Turbine Blade at Low Reynolds Numbers: Low-Speed Investigation

2005 ◽  
Vol 128 (3) ◽  
pp. 517-527 ◽  
Author(s):  
Xue Feng Zhang ◽  
Maria Vera ◽  
Howard Hodson ◽  
Neil Harvey
Keyword(s):  
Turbine Blade ◽  
Separation Bubble ◽  
Reynolds Numbers ◽  
Surface Boundary ◽  
Suction Surface ◽  
High Lift ◽  
Low Reynolds Numbers ◽  
Low Speed ◽  
Profile Losses ◽  
Low Reynolds

An experimental study was conducted to improve the performance of an aft-loaded ultra-high-lift low-pressure turbine blade known as U2 at low Reynolds numbers. This was achieved by manipulation of the laminar-turbulent transition process on the suction surface. The U2 profile was designed to meet the targets of reduced cost, weight and fuel burn of aircraft engines. The studies were conducted on both low-speed and high-speed experimental facilities under the unsteady flow conditions with upstream passing wakes. The current paper presents the low-speed investigation results. On the smooth suction surface, the incoming wakes are not strong enough to suppress the separation bubble due to the strong adverse pressure gradient on the suction surface and the low wake passing frequency, which allows the separation between the wakes more time to re-establish. Therefore, the profile losses of this ultra-high-lift blade are not as low as conventional or high-lift blades at low Reynolds numbers even in unsteady flows. Two different types of passive separation control devices, i.e., surface trips and air jets, were investigated to further improve the blade performance. The measurement results show that the profile losses can be further reduced to the levels similar to those of the high-lift and conventional blades due to the aft-loaded nature of this ultra-high-lift blade. Detailed surveys of the blade surface boundary layer developments showed that the loss reduction was due to the suppression of the separation underneath the wakes, the effect of the strengthened calmed region and the smaller separation bubble between wakes.

On Modeling the Operation of Slotted High-Lift Device Elements in a Spin Experiment at Low Reynolds Numbers

2021 ◽  
Vol 64 (3) ◽  
pp. 449-454
Author(s):  
G. N. Bogomazova ◽  
M. A. Golovkin ◽  
A. A. Efremov ◽  
O. V. Pavlenko
Keyword(s):  
Reynolds Numbers ◽  
High Lift ◽  
Low Reynolds Numbers ◽  
Low Reynolds

On Transition From Supersonic to Subsonic Flow at Low Reynolds Numbers in a Tube

1969 ◽  
Vol 36 (2) ◽  
pp. 146-150 ◽  
Author(s):  
R. Y. Chen ◽  
J. C. Williams
Keyword(s):  
Mach Number ◽  
Static Pressure ◽  
Subsonic Flow ◽  
Supersonic Nozzle ◽  
Reynolds Numbers ◽  
Impact Pressure ◽  
Low Reynolds Numbers ◽  
Pressure Distributions ◽  
Low Reynolds ◽  
The Impact

A supersonic low-density gas stream produced in a supersonic nozzle was passed through a circular tube in which the transition from supersonic to subsonic flow took place. Static pressure distributions along the tube (and nozzle) and impact pressure distributions across the tube at several stations were measured to determine the nature of this transition. The impact pressure distributions were used, together with the local static pressure, to infer Mach number and velocity profiles in the tube. When the pressure distributions and center-line Mach number distributions are considered together, one obtains a fairly clear picture of the processes involved in the transition from supersonic to subsonic flow at low Reynolds numbers.

Micro Vortex Flow Induced by Small Life

2007 ◽  
Author(s):  
O. Mochizuki
Keyword(s):  
High Speed ◽  
Ccd Camera ◽  
Reynolds Numbers ◽  
Artemia Salina ◽  
The Body ◽  
Power Stroke ◽  
Low Reynolds Numbers ◽  
Flapping Motion ◽  
Vortex Pairs ◽  
Low Reynolds

We investigated the relations between swimming motions and flow fields around plankton that is a larva of brine-shrimp (Artemia salina) and jellyfish (Aurelia aurita). These move in low Reynolds numbers by flapping motion in common. We recorded motions and flow by using a high speed CCD camera, and analyzed by a motion analysis and PIV method. We observed vortex pairs in each case as a result of power stroke and recovery stroke of pitching motion. Force acting on the body was estimated by measured acceleration of the body. Mechanism of generation of thrust force related to vortex pairs by flapping motion in low Reynolds number environment was discussed in this paper.

Sign in / Sign up

Export Citation Format

Share Document