Optimal Design of Swept, Leaned and Skewed Blades in a Transonic Axial Compressor

2006 ◽  
Author(s):  
Choon-Man Jang ◽  
Abudus Samad ◽  
Kwang-Yong Kim
Keyword(s):  
Shape Optimization ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Design Flow ◽  
Surface Boundary ◽  
Suction Surface ◽  
Surface Boundary Layer ◽  
Compressor Rotor ◽  
Design Variables ◽  
Transonic Axial Compressor

Shape optimization of a transonic axial compressor rotor operating at the design flow condition has been performed using the response surface method and three-dimensional Navier-Stokes analysis. The three design variables, blade sweep, lean and skew, are introduced to optimize the three-dimensional stacking line of the rotor blade. The objective function of the shape optimization is adiabatic efficiency. Throughout the shape optimization of the rotor, the adiabatic efficiency is increased by reducing the hub corner and tip losses. Separation line due to the interference between a passage shock and surface boundary layer on the blade suction surface is moved downstream for the optimized blade compared to the reference one. Among the three design variables, the blade skew is most effective to increase the adiabatic efficiency in the compressor rotor.

Unsteady Flow Behavior due to Breakdown of Tip Leakage Vortex in an Axial Compressor Rotor at Near-Stall Condition

2000 ◽  
Author(s):  
Masato Furukawa ◽  
Kazuhisa Saiki ◽  
Kazutoyo Yamada ◽  
Masahiro Inoue
Keyword(s):  
Unsteady Flow ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Surface Boundary ◽  
Pressure Side ◽  
Suction Surface ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Pressure Surface ◽  
Compressor Rotor

The unsteady flow nature caused by the breakdown of the tip leakage vortex in an axial compressor rotor at near-stall conditions has been investigated by unsteady three-dimensional Navier-Stokes flow simulations. The simulations show that the spiral-type breakdown of the tip leakage vortex occurs inside the rotor passage at the near-stall conditions. Downstream of the breakdown onset, the tip leakage vortex twists and turns violently with time, thus interacting with the pressure surface of the adjacent blade. The motion of the vortex and its interaction with the pressure surface are cyclic. The vortex breakdown causes significant changes in the nature of the tip leakage vortex, which result in the anomalous phenomena in the time-averaged flow fields near the tip at the near-stall conditions: no rolling-up of the leakage vortex downstream of the rotor, disappearance of the casing wall pressure trough corresponding to the leakage vortex, large spread of the low-energy fluid accumulating on the pressure side, and large pressure fluctuation on the pressure side. As the flow rate is decreased, the movement of the tip leakage vortex due to its breakdown becomes so large that the leakage vortex interacts with the suction surface as well as the pressure one. The interaction with the suction surface gives rise to the three-dimensional separation of the suction surface boundary layer.

scholarly journals Effect of Partial Span Aspiration on the Performance of a Transonic Axial Compressor Rotor: A Numerical Study

2015 ◽  
Vol 2015 ◽  
pp. 1-13
Author(s):  
Vijaykumar Jain ◽  
Quamber H. Nagpurwala ◽  
Abdul Nassar
Keyword(s):  
Boundary Layer ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Suction Side ◽  
Surface Boundary ◽  
Suction Surface ◽  
Stall Margin ◽  
Compressor Rotor ◽  
Transonic Axial Compressor

Aspiration in an axial compressor is normally regarded as sucking out the low momentum boundary layer from blade suction surface, thus lowering the chances of flow separation and consequently that of stall under off-design operation. However, the suction mass flow does not take part in useful work and leads to loss of engine power output. This paper deals with a new concept of natural aspiration to energize blade suction surface boundary layer by injecting some fluid from pressure to suction side through a part span slot on the blade. The energized boundary layer has lesser tendency to separate, thus enhancing stall margin. Numerical simulations were carried out to study the effect of aspiration slot location and geometry on the performance and stall margin of a transonic axial compressor rotor. The computational results without aspiration slot were in fair agreement with the published experimental data. The modified rotor, with part span aspiration, showed ~3.2% improvement in stall margin at design rotational speed. The pressure ratio and efficiency of the aspirated rotor dropped by ~1.42% and ~2.0%, respectively, whereas the structural analysis did not indicate any adverse effect on the blade stress distribution in the presence of aspiration slot.

scholarly journals Blockage Development in a Transonic, Axial Compressor Rotor

1997 ◽  
Author(s):  
Kenneth L. Suder
Keyword(s):  
Boundary Layer ◽  
Axial Compressor ◽  
Flow Region ◽  
Tip Clearance ◽  
Surface Boundary ◽  
Core Flow ◽  
The Core ◽  
Compressor Rotor ◽  
Transonic Axial Compressor ◽  
The Impact

A detailed experimental investigation to understand and quantify the development of blockage in the flow field of a transonic, axial flow compressor rotor (NASA Rotor 37) has been undertaken. Detailed laser anemometer measurements were acquired upstream, within, and downstream of a transonic, axial compressor rotor operating at 100%, 85%, 80%, and 60% of design speed which provided inlet relative Mach numbers at the blade tip of 1.48, 1.26, 1.18, and 0.89 respectively. The impact of the shock on the blockage development, pertaining to both the shock / boundary layer interactions and the shock / tip clearance flow interactions, is discussed. The results indicate that for this rotor the blockage in the endwall region is 2–3 times that of the core flow region, and the blockage in the core flow region more than doubles when the shock strength is sufficient to separate the suction surface boundary layer.

Physical Explanations of Tip Leakage Flow Field in an Axial Compressor Rotor

1998 ◽  
Author(s):  
Masahiro Inoue ◽  
Masato Furukawa ◽  
Kazuhisa Saiki ◽  
Kazutoyo Yamada
Keyword(s):  
Boundary Layer ◽  
Vortex Core ◽  
Leakage Flow ◽  
Surface Boundary ◽  
Suction Surface ◽  
Surface Boundary Layer ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Vortex Lines

Structure of a tip leakage flow field in an axial compressor rotor has been investigated by detailed numerical simulations and appropriate post-processing. Physical explanations of the structure are made in terms of vortex-core identification, normalized helicity, vortex-lines, limiting streamlines, etc. The onset of the discrete tip leakage vortex is located on the suction surface at some distance from the leading edge. The vortex core with high vorticity is generated from a shear layer between the leakage jet flow and the main flow. The streamlines in the leakage flow are coiling around the vortex core. All the vortex-lines in the tip leakage vortex core link to ones in the suction surface boundary layer. The other vortex-lines in the suction surface boundary layer link to the vortex-lines in the pressure surface boundary layer and in the casing wall boundary layer. There are two mechanisms to reduce intensity of the tip leakage vortex: one is reduction of discharged vorticity caused by the linkage of vortex-lines between the suction surface and casing wall boundary layers, and another is diffusion of vorticity from the tip leakage vortex. Relative motion of the endwall has a substantial influence on the structure of the leakage flow field. In the case of a compressor rotor, it intensifies streamwise vorticity of the leakage vortex but reduces leakage flow loss.

Control of separations in a highly loaded diffusion cascade by tailored boundary layer suction

2013 ◽  
Vol 228 (8) ◽  
pp. 1363-1374 ◽  
Author(s):  
Zhiyuan Cao ◽  
Bo Liu ◽  
Ting Zhang
Keyword(s):  
Boundary Layer ◽  
Static Pressure ◽  
Three Dimensional ◽  
Flow Fields ◽  
Separated Flows ◽  
Surface Boundary ◽  
Suction Surface ◽  
Surface Boundary Layer ◽  
Boundary Layer Suction ◽  
Highly Loaded

In order to explore the control mechanism of boundary layer suction on the separated flows of highly loaded diffusion cascades, a linear compressor cascade, which has separated flows on the whole span and three-dimensional separations over the suction surface/endwall corner, was investigated by tailored boundary layer suction. Three suction surface-slotted schemes and two combined suction surface/endwall-slotted schemes were designed. The original cascade and the cascade with part blade span suction were experimentally investigated on a high-subsonic cascade wind tunnel. In addition, numerical simulation was employed to study the flow fields of different suction schemes in detail. The results shows that while tailored boundary layer suction at part blade span can effectively remove the separations at the suction span, the flow fields of other spans deteriorated. The reasons are the ‘C’ shape or reverse ‘C’ shape spanwise distribution of static pressure after part blade span boundary layer suction. Suction surface boundary layer suction over the whole span can obviously eliminate the separation at the suction surface. However, because of the endwall boundary layer, suction surface boundary layer suction cannot effectively remove the corner three-dimensional separation. The separation over the whole span and the three-dimensional separation at the corner are completely eliminated by combined suction surface/endwall boundary layer suction. After combined boundary layer suction, the static pressure distribution over the blade span just like the shape of ‘C’ is good for the transport of the low-energy fluid near the endwall to the midspan.

Influence of Surface Roughness on Three-Dimensional Separation in Axial Compressors

2004 ◽  
Vol 126 (4) ◽  
pp. 455-463 ◽  
Author(s):  
Semiu A. Gbadebo ◽  
Tom P. Hynes ◽  
Nicholas A. Cumpsty
Keyword(s):  
Surface Roughness ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Leading Edge ◽  
Major Effect ◽  
Surface Flow ◽  
Design Flow ◽  
Flow Coefficient ◽  
Navier Stokes ◽  
Suction Surface

Surface roughness on a stator blade was found to have a major effect on the three-dimensional (3D) separation at the hub of a single-stage low-speed axial compressor. The change in the separation with roughness worsened performance of the stage. A preliminary study was carried out to ascertain which part of the stator suction surface and at what operating condition the flow is most sensitive to roughness. The results show that stage performance is extremely sensitive to surface roughness around the leading edge and peak-suction regions, particularly for flow rates corresponding to design and lower values. Surface flow visualization and exit loss measurements show that the size of the separation, in terms of spanwise and chordwise extent, is increased with roughness present. Roughness produced the large 3D separation at design flow coefficient that is found for smooth blades nearer to stall. A simple model to simulate the effect of roughness was developed and, when included in a 3D Navier–Stokes calculation method, was shown to give good qualitative agreement with measurements.

scholarly journals Design Optimization of a Dual-Bleeding Recirculation Channel to Enhance Operating Stability of a Transonic Axial Compressor

Energies ◽  
2021 ◽  
Vol 15 (1) ◽  
pp. 159
Author(s):  
Tien-Dung Vuong ◽  
Kwang-Yong Kim
Keyword(s):  
Design Optimization ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Aerodynamic Performance ◽  
Maximum Pressure ◽  
Stall Margin ◽  
Design Variables ◽  
Operating Stability ◽  
Transonic Axial Compressor

The present work performed a comprehensive investigation to find the effects of a dual-bleeding port recirculation channel on the aerodynamic performance of a single-stage transonic axial compressor, NASA Stage 37, and optimized the channel’s configuration to enhance the operating stability of the compressor. The compressor’s performance was examined using three parameters: The stall margin, adiabatic efficiency, and pressure ratio. Steady-state three-dimensional Reynolds-averaged Navier–Stokes analyses were performed to find the flow field and aerodynamic performance. The results showed that the addition of a bleeding channel increased the recirculation channel’s stabilizing effect compared to the single-bleeding channel. Three design variables were selected for optimization through a parametric study, which was carried out to examine the influences of six geometric parameters on the channel’s effectiveness. Surrogate-based design optimization was performed using the particle swarm optimization algorithm coupled with a surrogate model based on the radial basis neural network. The optimal design was found to increase the stall margin by 51.36% compared to the case without the recirculation channel with only 0.55% and 0.28% reductions in the peak adiabatic efficiency and maximum pressure ratio, respectively.

Three-Dimensional Turbulent Flow Field Downstream of a Single-Stage Axial Compressor Rotor

2000 ◽  
Author(s):  
Hongwei Ma ◽  
Haokang Jiang
Keyword(s):  
Flow Field ◽  
Turbulent Flow ◽  
Mass Flow ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Single Stage ◽  
Suction Surface ◽  
Trailing Edge ◽  
Rotor Wake ◽  
Compressor Rotor

This paper reports an experimental investigation of the three-dimensional turbulent flow downstream of a single-stage axial compressor rotor. The flow fields were measured at two axial locations in the rotor-stator gap at different mass-flow conditions. Both hot-wire probe and fast-response pressure probe were employed to survey the flow structure. At the design condition, substantial flow blockage, turbulence, loss and aerodynamic noise mainly occur in the tip mid-passage, the rotor wake and at the hub corner of the suction surface. The radial component is the highest of the three turbulence intensities at 15% axial chord downstream of the trailing edge. With the flow downstream, the radial turbulence components decay fast. Interactions of the tip leakage vorticities and the rotor wake are found at 30% axial chord downstream of the trailing edge. With the mass-flow decrease, the turbulence intensities and shear stresses become stronger, while the radial components increase fast. The flow separation and tangential migration of the low-energy fluids at the tip corner of the suction surface play an important role in the tip flow field at a low mass-flow condition.

Three-Dimensional Turbulent Flow of the Tip Leakage Vortex in an Axial Compressor Rotor Passage

2000 ◽  
Author(s):  
Hongwei Ma ◽  
Haokang Jiang
Keyword(s):  
Turbulent Flow ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Radial Component ◽  
Reynolds Stresses ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor

Three-dimensional turbulent flow of the tip leakage vortex in a single-stage axial compressor rotor passage is studied using a 3-Component Laser Doppler Velocimetry. The measurement results indicate that the tip leakage vortex originates at about 10% axial chord, 8% pitch away from the suction surface, and becomes strongest at about 30% chord. With the flow downstream, the vortex core moves toward the pressure surface and to a lower radial location, leading to substantial flow mixing, blockage and turbulence in the tip region. The radial component of turbulence intensities is found to be the highest while the axial-radial component of Reynolds stresses is the largest. Breakdown of the leakage vortex occurs inside the rear rotor passage, which makes the flow more turbulent in a wider region downstream. This viewpoint is confirmed by the measurements of unsteady static pressure on the casing wall. Breakdown of a leakage vortex is observed clearly in a compressor cascade with a small clearance. Unsteady interactions of the broken vorticities and the suction surface’s boundary layer are shown obviously inside the downstream passage.

Effect of Inflow Circumferential Distortion on a Transonic Axial Compressor

2017 ◽  
Author(s):  
Yuyun Li ◽  
Zhiheng Wang ◽  
Guang Xi
Keyword(s):  
Total Pressure ◽  
Rotor Blade ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Axial Compressor ◽  
Leading Edge ◽  
Inlet Distortion ◽  
Compressor Rotor ◽  
Structure Changes ◽  
Transonic Axial Compressor

The Inlet distortion, which may lead to the stability reduction or structure failure, is often non-ignorable in an axial compressor. In the paper, the three-dimensional unsteady numerical simulations on the flow in NASA rotor 67 are carried out to investigate the effect of inlet distortion on the performance and flow structure in a transonic axial compressor rotor. A sinusoidal circumferential total pressure distortion with eleven periods per revolution is adopted to study the interaction between the transonic rotor and inlet circumferential distortion. Concerning the computational expense, the flow in two rotor blade passages is calculated. Various intensities of the total pressure distortion are discussed, and the detailed flow structures under different rotating speeds near the peak efficiency condition are analyzed. It is found that the distortion has a positive effect on the flow near the hub. Even though there is no apparent decrease in the rotor efficiency or total pressure ratio, an obvious periodic loading exists over the whole blade. The blade loadings are concentrated in the region near the leading edge of the rotor blade or regions affected by the oscillating shocks near the pressure side. The time averaged location of shock structure changes little with the distortion, and the motion of shocks and the interactions between the shock and the boundary layer make a great contribution to the instability of the blade structure.

Sign in / Sign up

Export Citation Format

Share Document