Interaction of Rotor and Casing Treatment Flow in an Axial Single-Stage Transonic Compressor With Circumferential Grooves

Author(s):  
Martin W. Mu¨ller ◽  
Christoph Biela ◽  
Heinz-Peter Schiffer ◽  
Chunill Hah

The influence of circumferential grooves on the tip flow field of an axial single-stage transonic compressor rotor has been examined experimentally and numerically. The compressor stage provides a strongly increased stall margin with only small penalties in efficiency when the casing treatment is applied. Due to the complex interactions of the grooves with the rotor flow, unsteady measurement techniques have been chosen as an attempt to identify the aerodynamic effects responsible for the operating range extension. Therefore, the casing treatment has been instrumented with piezoresistive pressure sensors in the land between the grooves providing high-resolution static wall pressure measurements at different operating conditions. Data acquisition worked at a sampling rate of 125kHz, providing around 23 static pressure values per blade passage at 11 axial positions at the nominal speed of 20,000 rpm. A comparable dataset, but with 14 sensors, was obtained for the smooth casing. The results show the fluctuation of the tip leakage vortex and shock-vortex-interactions as well as the changed situation with casing treatment. Ensemble-averaged data shows tip leakage vortex trajectories. At near stall conditions with the smooth casing, the vortex hits the front part of the adjacent blade, which indicates the possibility of a spill forward of low momentum fluid into the next passage. Standard deviation values prove a high fluctuation of the pressure field over the tip gap. When the casing treatment is applied, the vortex trajectory maintains alignment along the blade’s suction side, thus preventing the onset of rotating stall. Results are presented as a back-to-back comparison of the smooth casing versus the treated casing at three operating conditions: peak efficiency at a mass flow rate of m˙pe = 16.2kg/s, near stall of the smooth casing at m˙nssc = 14.0kg/s and near stall of the treated casing at m˙ns = 12.6kg/s. Steady and unsteady numerical simulations of the rotor-only flow field have been calculated with and without grooves. These calculations aim at a broad analysis of the occurring flow phenomena at the rotor tip. Tip leakage flow behaviour and vortex trajectories are discussed in detail by summarizing the congruent findings of both numerical and experimental investigations.

Author(s):  
D. Schönweitz ◽  
M. Voges ◽  
G. Goinis ◽  
G. Enders ◽  
E. Johann

The flow in the blade tip vicinity of the transonic first stage of a multi-stage axial flow compressor with variable inlet guide vane (IGV) and casing treatment (CT) above the rotor is investigated experimentally and numerically with focus on the effects of the CT on flow structures and compressor performance. For the experimental part of this study, conventional performance instrumentation is used to estimate the operating condition of the compressor. Radial distributions of total temperature and total pressure are taken at the leading edges of the stators for comparison with simulations as well as for adjusting the operating conditions of the compressor. The velocity field in the rear part of the first-rotor is determined with Particle Image Velocimetry (PIV) at 90% and 96% radial height using two periscope light sheet probes. The employed PIV setup allows a spatial resolution of 0.7 mm × 0.7mm and thus a similar resolution as the spatial discretization in the simulation. For the numerical part of the study, time-accurate simulations are conducted for the same operating conditions as during experiments. Additional simulations of the same configuration with smooth casing are conducted in order to estimate the effect of the CT on the flow. The examination of PIV measurements and corresponding simulations exposes complex vortical structures originating from the interaction of the rotor bow shock with the IGV trailing edge, CT, IGV wake and the tip leakage vortex. The associated induced velocities together with the general passage flow form a complex flow field with significantly altered blockage compared to a common flow field in the tip vicinity. Position and trajectory of the tip leakage vortex are deduced from interactions between tip leakage vortex and IGV wake / CT. The detailed comparison of the tip region of simulations with and without CT shows that the CT influences pressure rise and flow parameters in a wide radial range due to a radial redistribution of the flow. Correspondingly, a rotor with CT can achieve an increased total pressure rise compared to a rotor with smooth casing, with only minor effects on the efficiency.


Author(s):  
Yasunori Sakuma ◽  
Toshinori Watanabe ◽  
Takehiro Himeno ◽  
Dai Kato ◽  
Takeshi Murooka ◽  
...  

The effect of a single circumferential casing groove on the stability enhancement of two different transonic compressors has been examined with CFD analysis. The differences in flow field and stall inception mechanism between two rotors are presented with principal focus on passage blockage and tip leakage flow behavior. Detailed observation showed that the blockage flow which leads the compressor to stall was different between each other. A parametric study conducted with respect to the axial location of the groove has clarified that the effect which groove has on the tip leakage flow behavior changes according to the blade tip loading and the design tip clearance gap at the location where the groove is applied. When the casing treatment was applied to the compressors with different instability mechanism, whether the casing treatment could enhance the stability of compressor or not was not only dependant on the extent of the influence which it had on the flow field but also on whether it could affect the original stall-initiating phenomena at the adequate location.


Author(s):  
Martin W. Mu¨ller ◽  
Heinz-Peter Schiffer ◽  
Chunill Hah

This paper reports on experimental and numerical investigations on circumferential grooves in an axial single-stage transonic compressor. Total pressure ratio and efficiency speedlines were taken at design speed and three off-design conditions. The experiments comprise four different configurations with deep and shallow grooves and variable coverage of the projected rotor axial chord. All casing treatments proved to have a beneficial effect on stall range while maintaining high levels of efficiency, even at off-design operation. Deep grooves extending almost to the trailing edge showed the biggest potential: the mass flow at stall inception for design speed could be strongly reduced, and the operating range could be enlarged by 56.1%. When three shallow grooves were applied to the compressor, the stage efficiency at design speed was shifted to slightly higher values. A possible explanation could be a favorable change in stator aerodynamics due to the reduction of corner separation. For a closer look into the physical effects of grooves on the tip leakage flow, a rotor-only CFD analysis has been carried out using a steady state calculation. A multi-block grid with approximately 1.2 million nodes was used. The numerical simulations reveal strong effects of circumferential grooves on the rotor flow field at tip. Mach-number contours, axial velocity distributions and particle traces for the smooth casing and six deep grooves are presented at stall mass flow. Compared to the smooth wall case, the treated casing significantly reduces blockage in the tip area and weakens the roll-up of the core vortex. These mechanisms prevent an early spillage of low momentum fluid into the adjacent blade passage and delay the onset of rotating stall.


Energies ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 4168
Author(s):  
Botao Zhang ◽  
Xiaochen Mao ◽  
Xiaoxiong Wu ◽  
Bo Liu

To explain the effect of tip leakage flow on the performance of an axial-flow transonic compressor, the compressors with different rotor tip clearances were studied numerically. The results show that as the rotor tip clearance increases, the leakage flow intensity is increased, the shock wave position is moved backward, and the interaction between the tip leakage vortex and shock wave is intensified, while that between the boundary layer and shock wave is weakened. Most of all, the stall mechanisms of the compressors with varying rotor tip clearances are different. The clearance leakage flow is the main cause of the rotating stall under large rotor tip clearance. However, the stall form for the compressor with half of the designed tip clearance is caused by the joint action of the rotor tip stall caused by the leakage flow spillage at the blade leading edge and the whole blade span stall caused by the separation of the boundary layer of the rotor and the stator passage. Within the investigated varied range, when the rotor tip clearance size is half of the design, the compressor performance is improved best, and the peak efficiency and stall margin are increased by 0.2% and 3.5%, respectively.


1997 ◽  
Vol 119 (1) ◽  
pp. 122-128 ◽  
Author(s):  
S. L. Puterbaugh ◽  
W. W. Copenhaver

An experimental investigation concerning tip flow field unsteadiness was performed for a high-performance, state-of-the-art transonic compressor rotor. Casing-mounted high frequency response pressure transducers were used to indicate both the ensemble averaged and time varying flow structure present in the tip region of the rotor at four different operating points at design speed. The ensemble averaged information revealed the shock structure as it evolved from a dual shock system at open throttle to an attached shock at peak efficiency to a detached orientation at near stall. Steady three-dimensional Navier Stokes analysis reveals the dominant flow structures in the tip region in support of the ensemble averaged measurements. A tip leakage vortex is evident at all operating points as regions of low static pressure and appears in the same location as the vortex found in the numerical solution. An unsteadiness parameter was calculated to quantify the unsteadiness in the tip cascade plane. In general, regions of peak unsteadiness appear near shocks and in the area interpreted as the shock-tip leakage vortex interaction. Local peaks of unsteadiness appear in mid-passage downstream of the shock-vortex interaction. Flow field features not evident in the ensemble averaged data are examined via a Navier-Stokes solution obtained at the near stall operating point.


Author(s):  
Xi Nan ◽  
Feng Lin ◽  
Takehiro Himeno ◽  
Toshinori Watanabe

Casing boundary layer effectively places a limit on the pressure rise capability achievable by the compressor. The separation of the casing boundary layer not only produce flow loss but also closely related to the compressor rotating stall. The motivation of this paper is to present a viewpoint that the casing boundary layer should be paid attention to in parallel with other flow factors on rotating stall trigger. This paper illustrates the casing boundary layer behavior by displaying its separation phenomena with the presence of tip leakage vortex at different flow conditions. Skin friction lines and the corresponding absolute streamlines are used to demonstrate the three-dimensional flow patterns on and near the casing. The results depict a Saddle, a Node and several tufts of skin friction lines dividing the passage into four zones. The tip leakage vortex is enfolded within one of the zones by the separated flows. All the flows in each blade passage are confined within the passage as long as the compressor is stable. The casing boundary layer of a transonic compressor is also examined in the same way, which results in qualitatively similar zonal flows that enfolds the tip leakage vortex. This research develops a new way to study the casing boundary layer in rotating compressors. The results may provide a first-principle based explanation to stalling mechanisms for compressors that are casing sensitive.


Author(s):  
Zhibo Zhang ◽  
Xianjun Yu ◽  
Baojie Liu

The detailed evolutionary processes of the tip leakage flow/vortex inside the rotor passage are still not very clear for the difficulties of investigating of them by both experimental and numerical methods. In this paper, the flow fields near the rotor tip region inside the blade passage with two tip gaps, 0.5% and 1.5% blade height respectively, were measured by using stereoscopic particle image velocimetry (SPIV) in a large-scale low speed axial compressor test facility. The measurements are conducted at four different operating conditions, including the design, middle, maximum static pressure rise and near stall conditions. In order to analyze the variations of the characteristics of the tip leakage vortex (TLV), the trajectory, concentration, size, streamwise velocity, and the blockage parameters are extracted from the ensemble-averaged results and compared at different compressor operating conditions and tip gaps. The results show that the formation of the TLV is delayed with large tip clearance, however, its trajectory moves much faster in an approximately linear way from the blade suction side to pressure side. In the tested compressor, the size of the tip gap has little effects on the scale of the TLV in the spanwise direction, on the contrary, its effects on the pitch-wise direction is very prominent. Breakdown of the TLV were both found at the near-stall condition with different tip gaps. The location of the initiation of the TLV breakdown moves downstream from the 60% chord to 70% chord as the tip gap increases. After the TLV breakdown occurs, the flow blockage near the rotor tip region increases abruptly. The peak value of the blockage effects caused by the TLV breakdown is doubled with the tip gap size increasing from 0.5% to 1.5% blade span.


2007 ◽  
Vol 130 (1) ◽  
Author(s):  
P. Palafox ◽  
M. L. G. Oldfield ◽  
J. E. LaGraff ◽  
T. V. Jones

New, detailed flow field measurements are presented for a very large low-speed cascade representative of a high-pressure turbine rotor blade with turning of 110deg and blade chord of 1.0m. Data were obtained for tip leakage and passage secondary flow at a Reynolds number of 4.0×105, based on exit velocity and blade axial chord. Tip clearance levels ranged from 0% to 1.68% of blade span (0% to 3% of blade chord). Particle image velocimetry was used to obtain flow field maps of several planes parallel to the tip surface within the tip gap, and adjacent passage flow. Vector maps were also obtained for planes normal to the tip surface in the direction of the tip leakage flow. Secondary flow was measured at planes normal to the blade exit angle at locations upstream and downstream of the trailing edge. The interaction between the tip leakage vortex and passage vortex is clearly defined, revealing the dominant effect of the tip leakage flow on the tip end-wall secondary flow. The relative motion between the casing and the blade tip was simulated using a motor-driven moving belt system. A reduction in the magnitude of the undertip flow near the end wall due to the moving wall is observed and the effect on the tip leakage vortex examined.


Author(s):  
Wei Wang ◽  
Wuli Chu ◽  
Haoguang Zhang ◽  
Yanhui Wu

Recirculating casing treatment (RCT) was studied in a subsonic axial flow compressor experimentally and numerically. The RCT was parameterized with the injector throat height and circumferential coverage percentage (ccp) to investigate its influence on compressor stability and on the overall performance in the experimentation. The injector throat height varied from 2 to 6 times the height of the rotor tip clearance, and the ccp ranged from 8.3% to 25% of the casing perimeter. Various RCT configurations were achieved with a modular design procedure. The rotor casing was instrumented with fast-response pressure transducers to detect the stall inception, rotational speed of stall cells, and pressure flow fields. Whole-passage unsteady simulations were also implemented for the RCT and solid casing to understand the flow details. Results indicate that both the compressor stability and overall performance can be improved through RCT with appropriate geometrical parameters. The effect of injector throat height on the stability depends on the choice of ccp, i.e., interaction effect exists. In general, the RCT with a moderate injector throat height and a large circumferential coverage is the optimal choice. Phase-locked pattern of the casing wall pressure reveals a weakened tip leakage vortex under the effect of RCT compared with the solid casing. The numerical results show that the RCT has a substantial effect on tip blockage even when the blade passages break away from the domain of RCT. The reduction of tip blockage induced by the tip leakage vortex is the main reason for the extension of stable operation range. The unsteadiness of double-leakage flow is detected both in the experiment and in numerical simulations. The pressure fluctuations caused by double-leakage flow are depressed with RCT. This observation indicates reduced losses related with the double-leakage flow. Although the stall inception is not changed by implementing RCT, the stall pattern is altered. The stall with two cells is detected in RCT compared with the solid casing with only one stall cell.


Sign in / Sign up

Export Citation Format

Share Document