Experimental and Numerical Analysis of Gas Turbine Blades With Different Internal Cooling Geometries

2009 ◽  
Author(s):  
M. Eifel ◽  
V. Caspary ◽  
H. Ho¨nen ◽  
P. Jeschke
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Pressure Ratio ◽  
Turbine Blades ◽  
Turbine Rotor ◽  
Base Flow ◽  
Internal Cooling ◽  
Turbine Rotor Blade ◽  
Flow Phenomena ◽  
Sst Turbulence Model

This paper presents the effects of major geometrical modifications to the interior of a convection cooled gas turbine rotor blade. The analysis of the flow is performed experimentally with flow visualization via paint injection into water whereas the flow and the heat transfer are investigated numerically with Ansys CFX utilizing the SST turbulence model. Two sets of calculations are carried out, one under the same conditions as the experiments and another according to realistic hot gas conditions with conjugate heat transfer. The aim is to identify flow phenomena altering the heat transfer in the blade and to manipulate them in order to reduce the thermal load of the material. The operating point of the geometric base configuration is set to Re = 50,000 at the inlet while for the modified geometries the pressure ratio is held constant compared to the base. Flow structures and heat transfer conditions are evaluated and are linked to specific geometric features. Among several investigated configurations one could be identified that leads to a cooling effectiveness 15% larger compared to the base.

Experimental and Numerical Analysis of Gas Turbine Blades With Different Internal Cooling Geometries

2010 ◽  
Vol 133 (1) ◽  
Author(s):  
M. Eifel ◽  
V. Caspary ◽  
H. Hönen ◽  
P. Jeschke
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Pressure Ratio ◽  
Turbine Blades ◽  
Turbine Rotor ◽  
Base Flow ◽  
Internal Cooling ◽  
Turbine Rotor Blade ◽  
Flow Phenomena ◽  
Sst Turbulence Model

This paper presents the effects of major geometrical modifications to the interior of a convection cooled gas turbine rotor blade. The analysis of the flow is performed experimentally with flow visualization via paint injection into water, whereas the flow and the heat transfer are investigated numerically with ANSYS CFX, utilizing the SST turbulence model. Two sets of calculations are carried out: one under the same conditions as the experiments and another according to realistic hot gas conditions with conjugate heat transfer. The aim is to identify flow phenomena altering the heat transfer in the blade and to manipulate them in order to reduce the thermal load of the material. The operating point of the geometric base configuration is set to Re=50,000 at the inlet while for the modified geometries, the pressure ratio is held constant compared with the base. Flow structures and heat transfer conditions are evaluated and are linked to specific geometric features. Among several investigated configurations one could be identified that leads to a cooling effectiveness 15% larger compared with the base.

Effect of Tip Gap and Squealer Geometry on Detailed Heat Transfer Measurements Over a High Pressure Turbine Rotor Blade Tip

2004 ◽  
Vol 126 (2) ◽  
pp. 221-228 ◽  
Author(s):  
Hasan Nasir ◽  
Srinath V. Ekkad ◽  
David M. Kontrovitz ◽  
Ronald S. Bunker ◽  
Chander Prakash
Keyword(s):  
Heat Transfer ◽  
Rotor Blade ◽  
Pressure Ratio ◽  
Turbine Blades ◽  
Turbine Rotor ◽  
Transfer Coefficients ◽  
Blow Down ◽  
Turbine Rotor Blade ◽  
Heat Transfer Coefficients ◽  
Gap Height

The present study explores the effects of gap height and tip geometry on heat transfer distribution over the tip surface of a HPT first-stage rotor blade. The pressure ratio (inlet total pressure to exit static pressure for the cascade) used was 1.2, and the experiments were run in a blow-down test rig with a four-blade linear cascade. A transient liquid crystal technique was used to obtain the tip heat transfer distributions. Pressure measurements were made on the blade surface and on the shroud for different tip geometries and tip gaps to characterize the leakage flow and understand the heat transfer distributions. Two different tip gap-to-blade span ratios of 1% and 2.6% are investigated for a plane tip, and a deep squealer with depth-to-blade span ratio of 0.0416. For a shallow squealer with depth-to-blade span ratio of 0.0104, only 1% gap-to-span ratio is considered. The presence of the squealer alters the tip gap flow field significantly and produces lower overall heat transfer coefficients. The effects of different partial squealer arrangements are also investigated for the shallow squealer depth. These simulate partial burning off of the squealer in real turbine blades. Results show that some partial burning of squealers may be beneficial in terms of overall reduction in heat transfer coefficients over the tip surface.

scholarly journals Oscillator Fin as a Novel Heat Transfer Augmentation Device for Gas Turbine Cooling Applications

1998 ◽  
Author(s):  
Oguz Uzol ◽  
Cengiz Camci
Keyword(s):  
Heat Transfer ◽  
Kinetic Energy ◽  
Gas Turbine ◽  
Turbulent Kinetic Energy ◽  
Stokes Equations ◽  
Turbine Blades ◽  
Local Heat Transfer ◽  
Internal Cooling ◽  
Pin Fin ◽  
Heat Transfer Augmentation

A new concept for enhanced turbulent transport of heat in internal coolant passages of gas turbine blades is introduced. The new heat transfer augmentation component called “oscillator fin” is based on an unsteady flow system using the interaction of multiple unsteady jets and wakes generated downstream of a fluidic oscillator. Incompressible, unsteady and two dimensional solutions of Reynolds Averaged Navier-Stokes equations are obtained both for an oscillator fin and for an equivalent cylindrical pin fin and the results are compared. Preliminary results show that a significant increase in the turbulent kinetic energy level occur in the wake region of the oscillator fin with respect to the cylinder with similar level of aerodynamic penalty. The new concept does not require additional components or power to sustain its oscillations and its manufacturing is as easy as a conventional pin fin. The present study makes use of an unsteady numerical simulation of mass, momentum, turbulent kinetic energy and dissipation rate conservation equations for flow visualization downstream of the new oscillator fin and an equivalent cylinder. Relative enhancements of turbulent kinetic energy and comparisons of the total pressure field from transient simulations qualitatively suggest that the oscillator fin has excellent potential in enhancing local heat transfer in internal cooling passages without significant aerodynamic penalty.

scholarly journals Calculation of Convective Heat Transfer in Square-Sectioned Gas Turbine Blade Cooling Channels

1998 ◽  
Author(s):  
Arash Saidi ◽  
Bengt Sundén
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Cross Sections ◽  
Turbine Blades ◽  
Solution Procedure ◽  
Navier Stokes ◽  
Internal Cooling ◽  
Turbine Blade Cooling ◽  
Cooling Channels ◽  
Energy Equations

Internal cooling channels are commonly used to reduce the thermal loads on the gas turbine blades to improve overall efficiency. In this study a numerical investigation has been carried out to provide a validated and consistent method to deal with the prediction of the fluid flow and the heat transfer of such channels with square cross sections. The rotation modified Navier-Stokes and energy equations together with a low-Re number version of the k-ε turbulence model are solved with appropriate boundary conditions. The solution procedure is based on a numerical method using a collocated grid, and the pressure-velocity coupling is handled by the SIMPLEC algorithm. The computations are performed with the assumption of fully developed periodic conditions. The calculations are carried out for smooth ducts with and without rotation and effects of rotation on the heat transfer are described. Similar numerical calculations have carried out for channels with rib-roughened walls. The obtained results are compared with available experimental data and empirical correlations for the heat transfer rate and the friction factor. Some details of the flow and heat transfer fields are also presented.

Topology Optimization of Serpentine Channels for Minimization of Pressure Loss and Maximization of Heat Transfer Performance As Applied for Additive Manufacturing

2019 ◽  
Author(s):  
Shinjan Ghosh ◽  
Jayanta S. Kapat
Keyword(s):  
Heat Transfer ◽  
Topology Optimization ◽  
Additive Manufacturing ◽  
Pressure Drop ◽  
Gas Turbine ◽  
Turbine Blades ◽  
Inlet Temperature ◽  
Internal Cooling ◽  
Cooling Channels ◽  
Blade Cooling

Abstract Gas Turbine blade cooling is an important topic of research, as a high turbine inlet temperature (TIT) essentially means an increase in efficiency of gas turbine cycles. Internal cooling channels in gas turbine blades are key to the cooling and prevention of thermal failure of the material. Serpentine channels are a common feature in internal blade cooling. Optimization methods are often employed in the design of blade internal cooling channels to improve heat-transfer and reduce pressure drop. Topology optimization uses a variable porosity approach to manipulate flow geometries by adding or removing material. Such a method has been employed in the current work to modify the geometric configuration of a serpentine channel to improve total heat transferred and reduce the pressure drop. An in-house OpenFOAM solver has been used to create non-traditional geometries from two generic designs. Geometry-1 is a 2-D serpentine passage with an inlet and 4 bleeding holes as outlets for ejection into the trailing edge. Geometry-2 is a 3-D serpentine passage with an aspect ratio of 3:1 and consists of two 180-degree bends. The inlet velocity for both the geometries was used as 20 m/s. The governing equations employ a “Brinkman porosity parameter” to account for the porous cells in the flow domain. Results have shown a change in shape of the channel walls to enhance heat-transfer in the passage. Additive manufacturing can be employed to make such unconventional shapes.

Comparison of Time-Resolved Turbine Rotor Blade Heat Transfer Measurements and Numerical Calculations

1991 ◽  
Author(s):  
R. S. Abhari ◽  
G. R. Guenette ◽  
A. H. Epstein ◽  
M. B. Giles
Keyword(s):  
Heat Transfer ◽  
Rotor Blade ◽  
Pressure Ratio ◽  
Time History ◽  
Turbine Rotor ◽  
Numerical Calculations ◽  
Test Facility ◽  
Time Resolved ◽  
Turbine Rotor Blade ◽  
History Of

Time-resolved turbine rotor blade heat transfer data are compared with ab initio numerical calculations. The data was taken on a transonic, 4-to-1 pressure ratio, uncooled, single-stage turbine in a short duration turbine test facility. The data consists of the time history of the heat transfer distribution about the rotor chord at midspan. The numerical calculation is a time accurate, 2-D, thin shear layer, multiblade row code known as UNSFLO. UNSFLO uses Ni’s Lax-Wendroff algorithm, conservative boundary conditions, and a time tilting algorithm to facilitate the calculation of the flow in multiple blade rows of arbitrary pitch ratio with relatively little computer time. The version used for this work had a simple algebraic Baldwin-Lomax turbulence model. The code is shown to do a good job of predicting the quantitative time history of the heat flux distribution. The wake/boundary layer and transonic interaction regions for suction and pressure surfaces are identified and the shortcomings of the current algebraic turbulence modelling in the code are discussed. The influence of hardware manufacturing tolerance on rotor heat transfer variation is discussed. A physical reasoning explaining the discrepancies between the unsteady measurement and the calculations for both the suction and pressure surfaces are given, which may be of use in improving future calculations and design procedures.

Conceptual Design and Cooling Blade Development of 1700°C Class High-Temperature Gas Turbine

2005 ◽  
Vol 127 (2) ◽  
pp. 358-368 ◽  
Author(s):  
Shoko Ito ◽  
Hiroshi Saeki ◽  
Asako Inomata ◽  
Fumio Ootomo ◽  
Katsuya Yamashita ◽  
...  
Keyword(s):  
Heat Transfer ◽  
High Temperature ◽  
Gas Turbine ◽  
Conceptual Design ◽  
Thermal Efficiency ◽  
Internal Cooling ◽  
Closed Cycle ◽  
Steam Consumption ◽  
Flow Phenomena ◽  
High Temperature Gas

In this paper we describe the conceptual design and cooling blade development of a 1700°C-class high-temperature gas turbine in the ACRO-GT-2000 (Advanced Carbon Dioxide Recovery System of Closed-Cycle Gas Turbine Aiming 2000 K) project. In the ACRO-GT closed cycle power plant system, the thermal efficiency aimed at is more than 60% of the higher heating value of fuel (HHV). Because of the high thermal efficiency requirement, the 1700°C-class high-temperature gas turbine must be designed with the minimum amount of cooling and seal steam consumption. The hybrid cooling scheme, which is a combination of closed loop internal cooling and film ejection cooling, was chosen from among several cooling schemes. The elemental experiments and numerical studies, such as those on blade surface heat transfer, internal cooling channel heat transfer, and pressure loss and rotor coolant passage distribution flow phenomena, were conducted and the results were applied to the conceptual design advancement. As a result, the cooling steam consumption in the first stage nozzle and blade was reduced by about 40% compared with the previous design that was performed in the WE-NET (World Energy Network) Phase-I.

Sign in / Sign up

Export Citation Format

Share Document