Computational Investigation of the Three-Dimensional Flow Structure and Losses in a Low Reynolds Number Microturbine

2011 ◽  
Author(s):  
M. Omri ◽  
L. G. Fre´chette
Keyword(s):  
Reynolds Number ◽  
Heat Engine ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Flow Patterns ◽  
Tip Clearance ◽  
3D Flow ◽  
Low Reynolds Numbers ◽  
Blade Passage ◽  
Low Reynolds

In this work, three dimensional numerical studies of the aerodynamics in laminar subsonic cascades at relatively low Reynolds numbers (Re < 2500) are presented. The stator and rotor blade designs are those for a MEMS-based Rankine microturbine power-plant-on-a-chip with 100 micron chord blades. Blade passage calculations in 2D and 3D were done for different Reynolds numbers, four different tip clearances (0%, 5%, 10% and 20%) and four incidences (0°, 5°, 10° and 15°) to determine the flow patterns and compute losses. These conditions are applied to a blade passage without rotation (stator) and with rotation (rotor), both for a stationary and moving outer casing. The 3D blade passage (without tip clearance) indicates the presence of two large symmetric vortices due to the interaction between flow curvature and hub/casing boundary layers. With tip clearance, a secondary vortex appears due to tip flow. This so-called tip vortex becomes dominant in the case of tip clearance above 10%. Relative wall motion also impacts the 3D flow patterns due to the important tangential drag at these low Reynolds numbers. Two dimensional calculations characterize well the flow at the mid-height plane, but are not sufficient for loss predictions due to the omission of the 3D flow structures. The 3D total losses increase dramatically for Re<500, which is similar to 2D studies. This suggests an operating Reynolds number greater than this to obtain efficiency levels necessary to operate a heat engine. The losses also increased monotonically with increasing tip clearance and incidence.

Experimental characterization of three-dimensional corner flows at low Reynolds numbers

2012 ◽  
Vol 707 ◽  
pp. 37-52 ◽  
Author(s):  
J. Sznitman ◽  
L. Guglielmini ◽  
D. Clifton ◽  
D. Scobee ◽  
H. A. Stone ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Numerical Solutions ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Secondary Flows ◽  
Channel Cross Section ◽  
Experimental Characterization ◽  
Low Reynolds Numbers ◽  
Low Reynolds

AbstractWe investigate experimentally the characteristics of the flow field that develops at low Reynolds numbers ($\mathit{Re}\ll 1$) around a sharp $9{0}^{\ensuremath{\circ} } $ corner bounded by channel walls. Two-dimensional planar velocity fields are obtained using particle image velocimetry (PIV) conducted in a towing tank filled with a silicone oil of high viscosity. We find that, in the vicinity of the corner, the steady-state flow patterns bear the signature of a three-dimensional secondary flow, characterized by counter-rotating pairs of streamwise vortical structures and identified by the presence of non-vanishing transverse velocities (${u}_{z} $). These results are compared to numerical solutions of the incompressible flow as well as to predictions obtained, for a similar geometry, from an asymptotic expansion solution (Guglielmini et al., J. Fluid Mech., vol. 668, 2011, pp. 33–57). Furthermore, we discuss the influence of both Reynolds number and aspect ratio of the channel cross-section on the resulting secondary flows. This work represents, to the best of our knowledge, the first experimental characterization of the three-dimensional flow features arising in a pressure-driven flow near a corner at low Reynolds number.

On High-Performance Airfoil at Very Low Reynolds Number

2016 ◽  
Vol 28 (3) ◽  
pp. 273-285
Author(s):  
Katsuya Hirata ◽  
◽  
Ryo Nozawa ◽  
Shogo Kondo ◽  
Kazuki Onishi ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Flat Plate ◽  
High Performance ◽  
Low Reynolds Number ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Aerodynamic Characteristics ◽  
Slow Flow ◽  
Low Reynolds Numbers ◽  
Low Reynolds

[abstFig src='/00280003/02.jpg' width=""300"" text='Iso-Q surfaces of very-slow flow past an iNACA0015' ] The airfoil is often used as the elemental device for flying/swimming robots, determining its basic performances. However, most of the aerodynamic characteristics of the airfoil have been investigated at Reynolds numbers Re’s more than 106. On the other hand, our knowledge is not enough in low Reynolds-number ranges, in spite of the recent miniaturisation of robots. In the present study, referring to our previous findings (Hirata et al., 2011), we numerically examine three kinds of high-performance airfoils proposed for very-low Reynolds numbers; namely, an iNACA0015 (the NACA0015 placed back to front), an FPBi (a flat plate blended with iNACA0015 as its upper half) and an FPBN (a flat plate blended with the NACA0015 as its upper half), in comparison with such basic airfoils as a NACA0015 and an FP (a flat plate), at a Reynolds number Re = 1.0 × 102 using two- and three-dimensional computations. As a result, the FPBi shows the best performance among the five kinds of airfoils.

scholarly journals Characteristics of an Annular Turbine Cascade at Low Reynolds Numbers

1998 ◽  
Author(s):  
Takayuki Matsunuma ◽  
Hiroyuki Abe ◽  
Yasukata Tsutsui ◽  
Koji Murata
Keyword(s):  
Reynolds Number ◽  
Gas Turbines ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Boundary Layer Separation ◽  
Aerodynamic Characteristics ◽  
Secondary Flows ◽  
Suction Surface ◽  
Low Reynolds Numbers ◽  
Low Reynolds

The aerodynamic characteristics of turbine cascades are thought to be relatively satisfactory due to the favorable pressure gradient of the accelerating flow. But within the low Reynolds number region of approximately 6×104 where the 300kW ceramic gas turbines which are being developed under the New Sunshine Project of Japan operate, the characteristics such as boundary layer separation, reattachment and secondary flow which lead to prominent power losses can not be easily predicted. In this research, experiments have been conducted to evaluate the performance of an annular turbine stator cascade. Wakes of the cascade were measured using a single hot wire and five hole pressure tube, for a range of blade chord Reynolds numbers based on the inlet condition from 2×104 to 12×104. Flow visualizations on the suction surface of the blade were carried out using oil film method. At low Reynolds numbers, the flow structure in the annular cascade was quite complex and three-dimensional. The separation line on the suction surface moved upstream due to the decrease of Reynolds number. In addition, the growth of secondary flows, i.e., passage vortices and leakage vortex, was extremely under the influence of Reynolds number.

Flow Characteristics Within and Downstream of Spherical and Cylindrical Dimple on a Flat Plate at Low Reynolds Numbers

2004 ◽  
Author(s):  
A. Khalatov ◽  
A. Byerley ◽  
D. Ochoa ◽  
Seong-Ki Min
Keyword(s):  
Reynolds Number ◽  
Turbulent Flow ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Reynolds Numbers ◽  
Flow Patterns ◽  
Flow Features ◽  
Laminar And Turbulent Flow ◽  
Low Reynolds ◽  
Oscillation Frequencies

A comprehensive experimental study has been performed in the U.S. Air Force Academy water tunnel to obtain a better understanding of the complicated flow patterns in shallow dimple configurations (h/D ≤ 0.1), including single cylindrical and spherical dimples, as well as single spanwise rows of dimples. The flow patterns, in-dimple separation zone extent, and bulk flow oscillation frequencies have been measured at low Reynolds number conditions. Three different single dimples and two single rows of dimples have been tested over a range of Reynolds numbers ReD of 3,170 to 23,590 including laminar and turbulent flow patterns downstream of a dimple. To visualize the fine flow features, five different colors of dye were injected through five cylindrical ports machined at locations upstream and inside the dimples. The measured results revealed unsteady and three-dimensional flow features inside and downstream of the dimple. The Reynolds number, dimple shape and the presence of adjacent dimples all play important roles in determining the nature of the flow pattern formation. Some preliminary conclusions regarding the laminar-turbulent flow transition after a dimple are presented.

scholarly journals Modelling boundary-layer transition on wings operating in ground effect at low Reynolds numbers

2018 ◽  
Vol 233 (11) ◽  
pp. 2820-2837 ◽  
Author(s):  
LS Roberts ◽  
MV Finnis ◽  
K Knowles
Keyword(s):  
Reynolds Number ◽  
Shear Stress ◽  
Wind Tunnel ◽  
Transport Model ◽  
Three Dimensional ◽  
Ground Effect ◽  
Reynolds Numbers ◽  
Low Reynolds Numbers ◽  
Shear Stress Transport Model ◽  
Low Reynolds

The transition-sensitive, three-equation k- kL- ω eddy-viscosity closure model was used for simulations of three-dimensional, single-element and multi-element wing configurations operating in close proximity to the ground. The aim of the study was to understand whether the model correctly simulated the transitional phenomena that occurred in the low Reynolds number operating conditions and whether it offered an improvement over the classical fully turbulent k-ω shear stress transport model. This was accomplished by comparing the simulation results to experiments conducted in a 2.7 m × 1.7 m closed-return, three-quarter-open-jet wind tunnel. The model was capable of capturing the presence of a laminar separation bubble on the wing and predicted sectional forces and surface-flow structures generated by the wings in wind tunnel testing to within 2.5% in downforce and 4.1% in drag for a multi-element wing. It was found, however, that the model produced insufficient turbulent kinetic energy during shear-layer reattachment, predicted turbulent trailing-edge separation prematurely in areas of large adverse pressure gradients, and was found to be very sensitive to inlet turbulence quantities. Despite these deficiencies, the model gave results that were much closer to wind-tunnel tests than those given by the fully turbulent k-ω shear stress transport model, which tended to underestimate downforce. Significant differences between the transitional and fully turbulent models in terms of pressure field, wake thickness and turbulent kinetic energy production were found and highlighted the importance of using transitional models for wings operating at low Reynolds numbers in ground effect. The k- kL- ω model has been shown to be appropriate for the simulation of separation-induced transition on a three-dimensional wing operating in ground effect at low Reynolds number.

Low Reynolds number flow around and heat transfer from a heated circular cylinder

2010 ◽  
Vol 1 (1-2) ◽  
pp. 15-20 ◽  
Author(s):  
B. Bolló
Keyword(s):  
Reynolds Number ◽  
Circular Cylinder ◽  
Lift Coefficient ◽  
Reynolds Numbers ◽  
Low Reynolds Numbers ◽  
Reynolds Number Flow ◽  
Two Dimensional Flow ◽  
Number Flow ◽  
Low Reynolds ◽  
Increasing Temperature

Abstract The two-dimensional flow around a stationary heated circular cylinder at low Reynolds numbers of 50 < Re < 210 is investigated numerically using the FLUENT commercial software package. The dimensionless vortex shedding frequency (St) reduces with increasing temperature at a given Reynolds number. The effective temperature concept was used and St-Re data were successfully transformed to the St-Reeff curve. Comparisons include root-mean-square values of the lift coefficient and Nusselt number. The results agree well with available data in the literature.

A Computational Study on Airfoils at a Low Reynolds Number

2000 ◽  
Author(s):  
Ajit Pal Singh ◽  
S. H. Winoto ◽  
D. A. Shah ◽  
K. G. Lim ◽  
Robert E. K. Goh
Keyword(s):  
Reynolds Number ◽  
Computational Analysis ◽  
Computational Study ◽  
Low Reynolds Number ◽  
Micro Air Vehicles ◽  
Reynolds Numbers ◽  
Aerodynamic Performance ◽  
Low Reynolds Numbers ◽  
Study Results ◽  
Low Reynolds

Abstract Performance characteristics of some low Reynolds number airfoils for the use in micro air vehicles (MAVs) are computationally studied using XFOIL at a Reynolds number of 80,000. XFOIL, which is based on linear-vorticity stream function panel method coupled with a viscous integral formulation, is used for the analysis. In the first part of the study, results obtained from the XFOIL have been compared with available experimental data at low Reynolds numbers. XFOIL is then used to study relative aerodynamic performance of nine different airfoils. The computational analysis has shown that the S1223 airfoil has a relatively better performance than other airfoils considered for the analysis.

scholarly journals Three-dimensional wake transition in the flow over four square cylinders at low Reynolds numbers

AIP Advances ◽  
2020 ◽  
Vol 10 (1) ◽  
pp. 015142
Author(s):  
Yuhang Zhang ◽  
Rui Wang ◽  
Yaoran Chen ◽  
Yan Bao ◽  
Zhaolong Han ◽  
...  
Keyword(s):  
Three Dimensional ◽  
Reynolds Numbers ◽  
Low Reynolds Numbers ◽  
Square Cylinders ◽  
Low Reynolds ◽  
Four Square ◽  
Wake Transition

Viscous constraints on microorganism approach and interaction

2018 ◽  
Vol 851 ◽  
pp. 715-738 ◽  
Author(s):  
Mehdi Jabbarzadeh ◽  
Henry Chien Fu
Keyword(s):  
Reynolds Number ◽  
Near Field ◽  
Reynolds Numbers ◽  
Suspended Particles ◽  
The Other ◽  
Direct Approach ◽  
Low Reynolds Numbers ◽  
Physical Constraints ◽  
Low Reynolds ◽  
Viscous Hydrodynamics

Microorganisms must approach other suspended organisms or particles in order to interact with them during a host of life processes including feeding and mating. Microorganisms live at low Reynolds number where viscosity dominates and strongly affects the hydrodynamics of swimmer and nearby cells and objects. Viscous hydrodynamics makes it difficult for two surfaces to approach closely at low Reynolds numbers. Nonetheless, it is observed that microorganisms in fluid are still able to approach closely enough to interact with each other or suspended particles. Here, we study how the physical constraints provided by viscous hydrodynamics affects the feasibility of direct approach of flagellated and ciliated microorganisms to targets of different sizes. We find that it is feasible for singly flagellated swimmers to approach targets that are the same size or bigger. On the other hand, for squirmers, the feasibility of approach depends on near-field flows that can be controlled by the details of their swimming strokes.

Low Reynolds-Number Experiments in an Axial-Flow Turbomachine

1964 ◽  
Vol 86 (3) ◽  
pp. 257-295 ◽  
Author(s):  
J. Neustein
Keyword(s):  
Reynolds Number ◽  
Guide Vane ◽  
Axial Flow ◽  
Reynolds Numbers ◽  
Low Flow ◽  
Working Fluid ◽  
Low Reynolds Numbers ◽  
Blade Row ◽  
Overall Performance ◽  
Low Reynolds

The performance of a single-stage, axial-flow turbomachine was studied experimentally at low Reynolds numbers. The study was made with a turbomachine modeled from a large jet-engine type of axial-flow compressor. Low Reynolds numbers were obtained by using a mixture of glycerine and water as the working fluid. The overall performance was determined over a range of Reynolds numbers RT (based on rotor-tip speed and rotor chord) from 2000 to 150,000. The flow rate at each Reynolds number was varied from near shutoff to the maximum permitted by the turbomachine-tunnel systems. Blade-row characteristics were studied by means of quantitative flow surveys before and after each blade row, and by means of extensive flow-visualization experiments within each blade row. The investigation established that sudden or critical changes in performance do not occur in the type of machine tested, between RT of 150,000 and 20,000. Below 20,000 the performance deteriorated more rapidly. A relatively sharp change in performance occurred between RT of 20,000 and 10,000. The results clarified many of the viscous flow details in each blade row which are associated with the deterioration of performance. These effects were very pronounced at RT of 4000 and below. Consequently, a considerable part of the paper is concerned with results obtained at these lower Reynolds numbers. From the point of view of a designer, information is presented in regard to overall performance, guide-vane turning, and guide-vane and stator total-pressure losses, all as functions of Reynolds number. These results are expected to be indicative of performance in turbomachines similar to the one tested here. Other details are concerned with problems such as wall boundary layers, flow reversal at low flow coefficients, lip-clearance flow, flow patterns near shutoff, and flow comparisons in stators with rotating and stationary hubs.

Sign in / Sign up

Export Citation Format

Share Document