A Comparison of Three Low Pressure Turbine Designs

2012 ◽  
Author(s):  
Christian T. Wakelam ◽  
Reinhard Niehuis ◽  
Martin Hoeger
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Total Pressure ◽  
Maximum Velocity ◽  
Suction Side ◽  
Surface Boundary ◽  
Suction Surface ◽  
Surface Boundary Layer ◽  
Pressure Losses ◽  
Pressure Surface

As part of the current research, three LPT geometries — which were designed with a common pitch, axial chord, inlet angle, and exit Mach number and to create the same nominal level of turning — are compared. Each of the LPT cascades was investigated under a range of Reynolds numbers, exit Mach numbers, and under the influence of a moving bar wake generator. Profile static pressure distributions, wake traverses at 5% and 40% axial chord downstream of the trailing edge and suction side boundary layer traverses were used to compare the performance of the three designs. The total pressure losses are strongly dependant on both the maximum velocity location as well as the diffusion on the suction surface. The importance of the behavior of the pressure surface boundary layer turned out to be negligible in comparison. Cases with equivalent operating Reynolds number and suction side diffusion level are compared in terms of the total pressure losses that are generated. It is shown that a relationship between loss and suction side maximum velocity location exists. An optimum suction side maximum velocity location depends on the Reynolds number, diffusion factor, and wake passing frequency.

A Comparison of Three Low Pressure Turbine Designs

2013 ◽  
Vol 135 (5) ◽  
Author(s):  
Christian T. Wakelam ◽  
Martin Hoeger ◽  
Reinhard Niehuis
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Total Pressure ◽  
Maximum Velocity ◽  
Suction Side ◽  
Low Pressure ◽  
Surface Boundary ◽  
Suction Surface ◽  
Pressure Losses ◽  
Low Pressure Turbine

As part of the current research, three low pressure turbine (LPT) geometries—which were designed with a common pitch, axial chord, inlet angle, and exit Mach number and to create the same nominal level of turning—are compared. Each of the LPT cascades was investigated under a range of Reynolds numbers, exit Mach numbers, and under the influence of a moving bar wake generator. Profile static pressure distributions, wake traverses at 5% and 40% axial chord downstream of the trailing edge, and suction side boundary layer traverses were used to compare the performance of the three designs. The total pressure losses are strongly dependent on both the maximum velocity location as well as the diffusion on the suction surface. The importance of the behavior of the pressure surface boundary layer turned out to be negligible in comparison. Cases with equivalent operating Reynolds number and suction side diffusion level are compared in terms of the total pressure losses that are generated. It is shown that a relationship between loss and suction side maximum velocity location exists. An optimum suction side maximum velocity location depends on the Reynolds number, diffusion factor, and wake passing frequency.

Boundary Layer Development in the BR710 and BR715 LP Turbines—The Implementation of High-Lift and Ultra-High-Lift Concepts

2002 ◽  
Vol 124 (3) ◽  
pp. 385-392 ◽  
Author(s):  
R. J. Howell ◽  
H. P. Hodson ◽  
V. Schulte ◽  
R. D. Stieger ◽  
Heinz-Peter Schiffer ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Test Facility ◽  
Surface Boundary ◽  
Unsteady Boundary Layer ◽  
Suction Surface ◽  
High Lift ◽  
Surface Boundary Layer ◽  
Cold Flow ◽  
Layer Behavior ◽  
Lp Turbine

This paper describes a detailed study into the unsteady boundary layer behavior in two high-lift and one ultra-high-lift Rolls-Royce Deutschland LP turbines. The objectives of the paper are to show that high-lift and ultra-high-lift concepts have been successfully incorporated into the design of these new LP turbine profiles. Measurements from surface mounted hot film sensors were made in full size, cold flow test rigs at the altitude test facility at Stuttgart University. The LP turbine blade profiles are thought to be state of the art in terms of their lift and design philosophy. The two high-lift profiles represent slightly different styles of velocity distribution. The first high-lift profile comes from a two-stage LP turbine (the BR710 cold-flow, high-lift demonstrator rig). The second high-lift profile tested is from a three-stage machine (the BR715 LPT rig). The ultra-high-lift profile measurements come from a redesign of the BR715 LP turbine: this is designated the BR715UHL LP turbine. This ultra-high-lift profile represents a 12 percent reduction in blade numbers compared to the original BR715 turbine. The results from NGV2 on all of the turbines show “classical” unsteady boundary layer behavior. The measurements from NGV3 (of both the BR715 and BR715UHL turbines) are more complicated, but can still be broken down into classical regions of wake-induced transition, natural transition and calming. The wakes from both upstream rotors and NGVs interact in a complicated manner, affecting the suction surface boundary layer of NGV3. This has important implications for the prediction of the flows on blade rows in multistage environments.

Physical Explanations of Tip Leakage Flow Field in an Axial Compressor Rotor

1998 ◽  
Author(s):  
Masahiro Inoue ◽  
Masato Furukawa ◽  
Kazuhisa Saiki ◽  
Kazutoyo Yamada
Keyword(s):  
Boundary Layer ◽  
Vortex Core ◽  
Leakage Flow ◽  
Surface Boundary ◽  
Suction Surface ◽  
Surface Boundary Layer ◽  
Tip Leakage Vortex ◽  
Tip Leakage ◽  
Compressor Rotor ◽  
Vortex Lines

Structure of a tip leakage flow field in an axial compressor rotor has been investigated by detailed numerical simulations and appropriate post-processing. Physical explanations of the structure are made in terms of vortex-core identification, normalized helicity, vortex-lines, limiting streamlines, etc. The onset of the discrete tip leakage vortex is located on the suction surface at some distance from the leading edge. The vortex core with high vorticity is generated from a shear layer between the leakage jet flow and the main flow. The streamlines in the leakage flow are coiling around the vortex core. All the vortex-lines in the tip leakage vortex core link to ones in the suction surface boundary layer. The other vortex-lines in the suction surface boundary layer link to the vortex-lines in the pressure surface boundary layer and in the casing wall boundary layer. There are two mechanisms to reduce intensity of the tip leakage vortex: one is reduction of discharged vorticity caused by the linkage of vortex-lines between the suction surface and casing wall boundary layers, and another is diffusion of vorticity from the tip leakage vortex. Relative motion of the endwall has a substantial influence on the structure of the leakage flow field. In the case of a compressor rotor, it intensifies streamwise vorticity of the leakage vortex but reduces leakage flow loss.

Predicting the Profile Loss of High-Lift Low Pressure Turbines

2011 ◽  
Vol 134 (2) ◽  
Author(s):  
John D. Coull ◽  
Howard P. Hodson
Keyword(s):  
Boundary Layer ◽  
Velocity Distribution ◽  
Low Pressure ◽  
Design Tool ◽  
Surface Boundary ◽  
Preliminary Design ◽  
Suction Surface ◽  
Surface Boundary Layer ◽  
Blade Loading ◽  
Profile Loss

The overall efficiency of low pressure turbines is largely determined by the two-dimensional profile loss, which is dominated by the contribution of the suction surface boundary layer. This boundary layer typically features a laminar separation bubble and is subjected to an inherently unsteady disturbance environment. The complexity of the flow behavior makes it difficult to numerically predict the profile loss. To address this problem, an empirical method is proposed for predicting the boundary layer integral parameters at the suction surface trailing edge, allowing the profile loss to be estimated. Extensive measurements have been conducted on a flat plate simulation of the suction surface boundary layer. The disturbance environment of real machines was modeled using a moving bar wake generator and a turbulence grid. From this data set, empirically based methods have been formulated using physical principles for the prediction of the momentum thickness and shape factor at the suction surface trailing edge. The predictions of these methods may be used to estimate the profile loss of a given cascade, which achieves reasonable agreement with the available data. By parameterizing the shape of the suction surface velocity distribution, the method is recast as a preliminary design tool. Powerfully, this may be used to guide the selection of the key design parameters (such as the blade loading and velocity distribution shape) and enables a reasonable estimation of the unsteady profile loss to be made at a very early stage of design. To illustrate the capabilities of the preliminary design tool, different styles of velocity distribution are evaluated for fixed blade loading and flow angles. The predictions suggest that relatively “flat-top” designs will have the lowest profile loss but good performance can also be achieved with front-loaded “peaky” distributions. The latter designs are more likely to have acceptable incidence tolerance.

scholarly journals Effect of Reynolds Number on Separation Bubbles on Controlled-Diffusion Compressor Blades in Cascade

1998 ◽  
Author(s):  
Garth V. Hobson ◽  
Denis J. Hansen ◽  
David G. Schnorenberg ◽  
Darren V. Grove
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Separation Bubble ◽  
Boundary Layer Separation ◽  
Surface Flow ◽  
Flow Reversal ◽  
Surface Boundary ◽  
Suction Surface ◽  
Flow Angle ◽  
Controlled Diffusion

A detailed experimental investigation of second-generation, controlled-diffusion, compressor stator blades at an off-design inlet-flow angle was performed in a low-speed cascade wind tunnel primarily using laser-Doppler velocimetry (LDV). The object of the study was to characterize the off-design flowfield and to obtain LDV measurements of the suction surface boundary layer separation which occurred near mid chord. The effect of Reynolds number on the flow separation in the regime of 210,000 to 640,000 was investigated. Surface flow visualization showed that at the low Re. no. the mid-chord separation bubble started laminar and reattached turbulent within 20% chord on the suction side of the blade. The extent of the bubble compared very well with the measured blade surface pressure distribution which showed a classical plateau and then diffusion in the turbulent region. LDV measurements of the flow reversal in the bubble were performed. At the intermediate Re. no. the boundary layer was transitional before the bubble which had decreased significantly in size (down to 10% chord). At the highest Re. no. the flow was turbulent from close to the leading edge, and three-dimensional flow reversal as a result of endwall effects appeared at approximately 80% chord which did not reattach.

The Influence of Large-Scale, High-Intensity Turbulence on Vane Aerodynamic Losses, Wake Growth, and the Exit Turbulence Parameters

1997 ◽  
Vol 119 (2) ◽  
pp. 182-192 ◽  
Author(s):  
F. E. Ames ◽  
M. W. Plesniak
Keyword(s):  
Boundary Layer ◽  
High Intensity ◽  
Total Pressure ◽  
Large Scale ◽  
Free Stream ◽  
Turbulent Shear ◽  
Surface Boundary ◽  
Suction Surface ◽  
Free Stream Turbulence ◽  
Eddy Diffusivities

An experimental research program was undertaken to examine the influence of large-scale high-intensity turbulence on vane exit losses, wake growth, and exit turbulence characteristics. The experiment was conducted in a four-vane linear cascade at an exit Reynolds number of 800,000 based on chord length and an exit Mach number of 0.27. Exit measurements were made for four inlet turbulence conditions including a low-turbulence case (Tu ≈ 1 percent), a grid-generated turbulence case (Tu ≈ 7.5. percent) and two levels of large-scale turbulence generated with a mock combustor (Tu ≈ 12 and 8 percent). Exit total pressure surveys were taken at two locations to quantify total pressure losses. The suction surface boundary layer was also traversed to determine losses due to boundary layer growth. Losses occurred in the core of the flow for the elevated turbulence cases. The elevated free-stream turbulence was found to have a significant effect on wake growth. Generally, the wakes subjected to elevated free-stream turbulence were broader and had smaller peak velocity deficits. Reynolds stress profiles exhibited asymmetry in peak amplitudes about the wake centerline, which are attributable to differences in the evolution of the boundary layers on the pressure and suction surfaces of the vanes. The overall level of turbulence and dissipation inside the wakes and in the free stream was determined to document the rotor inlet boundary conditions. This is useful information for assessing rotor heat transfer and aerodynamics. Eddy diffusivities and mixing lengths were estimated using X-wire measurements of turbulent shear stress. The free-stream turbulence was found to strongly affect eddy diffusivities, and thus wake mixing. At the last measuring position, the average eddy diffusivity in the wake of the high-turbulence close combustor configuration (Tu ≈ 12) was three times that of the low turbulence wake.

scholarly journals Direct numerical simulations of transition in a compressor cascade: the influence of free-stream turbulence

2010 ◽  
Vol 665 ◽  
pp. 57-98 ◽  
Author(s):  
TAMER A. ZAKI ◽  
JAN G. WISSINK ◽  
WOLFGANG RODI ◽  
PAUL A. DURBIN
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Free Stream ◽  
Transition To Turbulence ◽  
Surface Boundary ◽  
Bypass Transition ◽  
Suction Surface ◽  
Surface Boundary Layer ◽  
Laminar Separation ◽  
Free Stream Turbulence

The flow through a compressor passage without and with incoming free-stream grid turbulence is simulated. At moderate Reynolds number, laminar-to-turbulence transition can take place on both sides of the aerofoil, but proceeds in distinctly different manners. The direct numerical simulations (DNS) of this flow reveal the mechanics of breakdown to turbulence on both surfaces of the blade. The pressure surface boundary layer undergoes laminar separation in the absence of free-stream disturbances. When exposed to free-stream forcing, the boundary layer remains attached due to transition to turbulence upstream of the laminar separation point. Three types of breakdowns are observed; they combine characteristics of natural and bypass transition. In particular, instability waves, which trace back to discrete modes of the base flow, can be observed, but their development is not independent of the Klebanoff distortions that are caused by free-stream turbulent forcing. At a higher turbulence intensity, the transition mechanism shifts to a purely bypass scenario. Unlike the pressure side, the suction surface boundary layer separates independent of the free-stream condition, be it laminar or a moderate free-stream turbulence of intensityTu~ 3%. Upstream of the separation, the amplification of the Klebanoff distortions is suppressed in the favourable pressure gradient (FPG) region. This suppression is in agreement with simulations of constant pressure gradient boundary layers. FPG is normally stabilizing with respect to bypass transition to turbulence, but is, thereby, unfavourable with respect to separation. Downstream of the FPG section, a strong adverse pressure gradient (APG) on the suction surface of the blade causes the laminar boundary layer to separate. The separation surface is modulated in the instantaneous fields of the Klebanoff distortion inside the shear layer, which consists of forward and backward jet-like perturbations. Separation is followed by breakdown to turbulence and reattachment. As the free-stream turbulence intensity is increased,Tu~ 6.5%, transitional turbulent patches are initiated, and interact with the downstream separated flow, causing local attachment. The calming effect, or delayed re-establishment of the boundary layer separation, is observed in the wake of the turbulent events.

scholarly journals Moving Surface Boundary Layer Technique For NACA 0012 Airfoil At Ultra-Low Reynolds Number

2019 ◽  
Vol 9 (2) ◽  
pp. 3788-3795
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Low Reynolds Number ◽  
Leading Edge ◽  
Control Technique ◽  
Surface Boundary ◽  
Moving Surface ◽  
Surface Boundary Layer ◽  
Number Range ◽  
Low Reynolds

Application of moving surface boundary layer control technique has been confined to relatively high Reynolds numbers. The present paper reports a numerical study of application of the above flow technique in the ultra-low Reynolds number range. A two dimensional incompressible unstructured grid based Navier Stokes solver has been used for conducting the numerical studies. Moving surface has been applied at three different portions on the airfoil surface, firstly, in the form of a rotating leading edge portion of the airfoil, secondly, a continuous moving surface from leading edge of airfoil to 57% of the chord along the leeward surface of the airfoil and thirdly a continuous moving surface from leading edge to 97% of the chord along the leeward surface of the airfoil. All the moving surface configurations show improvement of aerodynamic performance of the airfoil through enhancement of lift and decrement of drag as compared to a fixed surface one

The Influence of Large Scale, High Intensity Turbulence on Vane Aerodynamic Losses, Wake Growth, and the Exit Turbulence Parameters

1995 ◽  
Author(s):  
Forrest E. Ames ◽  
Michael W. Plesniak
Keyword(s):  
Boundary Layer ◽  
High Intensity ◽  
Total Pressure ◽  
Large Scale ◽  
Free Stream ◽  
Turbulent Shear ◽  
Surface Boundary ◽  
Suction Surface ◽  
Free Stream Turbulence ◽  
Eddy Diffusivities

An experimental research program was undertaken to examine the influence of large-scale high, intensity turbulence on vane exit losses, wake growth, and exit turbulence characteristics. The experiment was conducted in a four vane linear cascade at an exit Reynolds number of 800, 000 based on chord length and an exit Mach number of 0.27. Exit measurements were made for four inlet turbulence conditions including a low turbulence case (Tu ≈ 1%), a grid-generated turbulence case (Tu ≈ 7.5%), and two levels of large-scale turbulence generated with a mock combustor (Tu ≈ 12% & Tu ≈ 8%). Exit total pressure surveys were taken at two locations to quantify total pressure losses. The suction surface boundary layer was also traversed to determine losses due boundary layer growth. Losses were also found in the core of the flow for the elevated turbulence cases. The elevated free stream turbulence was found to have a significant effect on wake growth. Generally, the wakes subjected to elevated free stream turbulence were broader and had smaller peak velocity deficits. Reynolds stress profiles exhibited asymmetry in peak amplitudes about the wake centerline, which are attributable to differences in the evolution of the boundary layers on the pressure and suction surfaces of the vanes. The overall level of turbulence and dissipation inside the wakes and in the free stream was determined to document the rotor inlet boundary conditions. This is useful information for assessing rotor heat transfer and aerodynamics. Eddy diffusivities and mixing lengths were estimated using X-wire measurements of turbulent shear stress. The free stream turbulence was found to strongly affect eddy diffusivities, and thus wake mixing. At the last measuring position, the average eddy diffusivity in the wake of the high turbulence close combustor configuration (Tu ≈ 12) was three times that of the low turbulence wake.

Control of separations in a highly loaded diffusion cascade by tailored boundary layer suction

2013 ◽  
Vol 228 (8) ◽  
pp. 1363-1374 ◽  
Author(s):  
Zhiyuan Cao ◽  
Bo Liu ◽  
Ting Zhang
Keyword(s):  
Boundary Layer ◽  
Static Pressure ◽  
Three Dimensional ◽  
Flow Fields ◽  
Separated Flows ◽  
Surface Boundary ◽  
Suction Surface ◽  
Surface Boundary Layer ◽  
Boundary Layer Suction ◽  
Highly Loaded

In order to explore the control mechanism of boundary layer suction on the separated flows of highly loaded diffusion cascades, a linear compressor cascade, which has separated flows on the whole span and three-dimensional separations over the suction surface/endwall corner, was investigated by tailored boundary layer suction. Three suction surface-slotted schemes and two combined suction surface/endwall-slotted schemes were designed. The original cascade and the cascade with part blade span suction were experimentally investigated on a high-subsonic cascade wind tunnel. In addition, numerical simulation was employed to study the flow fields of different suction schemes in detail. The results shows that while tailored boundary layer suction at part blade span can effectively remove the separations at the suction span, the flow fields of other spans deteriorated. The reasons are the ‘C’ shape or reverse ‘C’ shape spanwise distribution of static pressure after part blade span boundary layer suction. Suction surface boundary layer suction over the whole span can obviously eliminate the separation at the suction surface. However, because of the endwall boundary layer, suction surface boundary layer suction cannot effectively remove the corner three-dimensional separation. The separation over the whole span and the three-dimensional separation at the corner are completely eliminated by combined suction surface/endwall boundary layer suction. After combined boundary layer suction, the static pressure distribution over the blade span just like the shape of ‘C’ is good for the transport of the low-energy fluid near the endwall to the midspan.

Sign in / Sign up

Export Citation Format

Share Document