A 3D Time-Accurate CFD Simulation of the Flow Field Inside a Vaneless Diffuser During Rotating Stall Conditions

2016 ◽  
Author(s):  
Michele Marconcini ◽  
Alessandro Bianchini ◽  
Matteo Checcucci ◽  
Giovanni Ferrara ◽  
Andrea Arnone ◽  
...  
Keyword(s):  
Cfd Simulation ◽  
Pressure Field ◽  
Mechanical Stability ◽  
Aerodynamic Force ◽  
Rotating Stall ◽  
Regulation System ◽  
Vaneless Diffuser ◽  
Return Channel ◽  
University Of Florence ◽  
The University

An accurate characterization of rotating stall in terms of inception modality, flow structures, and stabilizing force is one of the key goals for high-pressure centrifugal compressors. The unbalanced pressure field that is generated within the diffuser can be in fact connected to a non-negligible aerodynamic force and then to the onset of detrimental sub-synchronous vibrations which can prevent the machine from operating beyond this limit. An inner comprehension on how the induced flow pattern in these conditions affects the performance of the impeller and its mechanical stability can therefore lead to the development of a more effective regulation system able to mitigate the effects of the phenomenon and extend the left-side margin of the operating curve. In the present study, a 3D-unsteady CFD approach was applied to the simulation of a radial stage model including the impeller, the vaneless diffuser and the return channel. Simulations were carried out with the TRAF code of the University of Florence. The tested rotor was an industrial impeller operating at high peripheral Mach number, for which unique experimental pressure measurements, including the spatial reconstruction of the pressure field at the diffuser inlet, were available. The comparison between experiments and simulations showed a good matching and corroborated the CFD capabilities in correctly describing also some of the complex unsteady phenomena taking place in proximity of the left margin of the operating curve.

A Three-Dimensional Time-Accurate Computational Fluid Dynamics Simulation of the Flow Field Inside a Vaneless Diffuser During Rotating Stall Conditions

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
Michele Marconcini ◽  
Alessandro Bianchini ◽  
Matteo Checcucci ◽  
Giovanni Ferrara ◽  
Andrea Arnone ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Pressure Field ◽  
Mechanical Stability ◽  
Aerodynamic Force ◽  
Three Dimensional ◽  
Rotating Stall ◽  
Dynamics Simulation ◽  
Regulation System ◽  
Vaneless Diffuser

An accurate characterization of rotating stall in terms of inception modality, flow structures, and stabilizing force is one of the key goals for high-pressure centrifugal compressors. The unbalanced pressure field that is generated within the diffuser can be in fact connected to a non-negligible aerodynamic force and then to the onset of detrimental subsynchronous vibrations, which can prevent the machine from operating beyond this limit. An inner comprehension on how the induced flow pattern in these conditions affects the performance of the impeller and its mechanical stability can therefore lead to the development of a more effective regulation system able to mitigate the effects of the phenomenon and extend the left-side margin of the operating curve. In the present study, a 3D-unsteady computational fluid dynamics (CFD) approach was applied to the simulation of a radial stage model including the impeller, the vaneless diffuser, and the return channel. Simulations were carried out with the TRAF code of the University of Florence. The tested rotor was an industrial impeller operating at high peripheral Mach number, for which unique experimental pressure measurements, including the spatial reconstruction of the pressure field at the diffuser inlet, were available. The comparison between experiments and simulations showed a good matching and corroborated the CFD capabilities in correctly describing also some of the complex unsteady phenomena taking place in proximity of the left margin of the operating curve.

Numerical and Experimental Study on Rotating Stall in Industrial Centrifugal Compressor

2020 ◽  
Author(s):  
Toshimasa Miura ◽  
Hideaki Yamashita ◽  
Ryota Takeuchi ◽  
Naoto Sakai
Keyword(s):  
Cfd Simulation ◽  
Aerodynamic Force ◽  
Rotating Stall ◽  
Gas Pressure ◽  
Experimental Result ◽  
Vaneless Diffuser ◽  
Vibration Prediction ◽  
Multiple Cell ◽  
Shaft Vibration ◽  
Good Agreement

Abstract Centrifugal compressors employed in the oil and gas industry are operated at high gas pressure conditions and are used in a wide operation range. Accurate prediction of the rotating stall and the destabilizing aerodynamic force is one of the key technologies for these compressors, because rotating stall can sometimes cause severe problems with subsynchronous shaft vibration and limit its operation range. Thus, the aim of this study is to establish a method of accurately predicting the inception of rotating stall and its effect on shaft vibration. To achieve this, numerical investigations are carried out by unsteady Reynolds-averaged Navier-Stokes (RANS) simulation with a full annulus model of the compressor stage. Also, to assess the accuracy of the simulation qualitatively and quantitatively, a high-pressure compressor test rig that contains a shrouded impeller and a vaneless diffuser is built. To investigate the effect of the rotating stall on the shaft vibration, an experiment is carried out at relatively high gas pressure with the inlet pressure level exceeding 30 barA. In the first part of the study, the accuracy of compressor performance prediction is studied by steady computational fluid dynamics (CFD) simulation. It is found that by taking the wall roughness effect into account, the predicted performance shows good agreement with the experimental result. Thus, a subsequent study of the rotating stall is also carried out by considering its effect. In the second part of the study, the accuracy of predicting the rotating stall is studied. In the experiment, two types of rotating stall are measured. One is a multiple-cell stall induced in the vaneless diffuser, for which the speed of rotation is relatively low and the other is a one-cell stall induced in the impeller region. The properties of the multiple-cell stall agree with the previous experimental and numerical studies, and the rotating stall has the limited effect on shaft vibration. Conversely, the one-cell stall shows severe subsynchronous vibration. In this study, both types of stall prediction are examined by CFD simulation. It is found that the simulation can predict the inception of the rotating stall with relatively high accuracy as the predicted results show good agreement with the experimental results in terms of cell count, rotation speed, pressure fluctuation level and the effect on shaft vibration. Through this study, the effectiveness of unsteady CFD simulation is confirmed for these types of stall and vibration prediction.

Experimental Characterization of Vaneless Diffuser Rotating Stall: Part VI — Reduction of Three Impeller Results

2006 ◽  
Author(s):  
E. A. Carnevale ◽  
G. Ferrara ◽  
L. Ferrari ◽  
L. Baldassarre
Keyword(s):  
Rotating Stall ◽  
Radius Ratio ◽  
Vaneless Diffuser ◽  
Cross Sectional ◽  
Stall Inception ◽  
Return Channel ◽  
Geometrical Scale ◽  
And Diffusion ◽  
Basic Configuration

Vaneless diffuser rotating stall is a major problem for centrifugal compressors since it is a limit to their working range. In the literature some good correlations for predicting stall inception can be found but they do not adequately cover the case of the last stage configuration, especially for very low blade-outlet-width-to-impeller-radius-ratio impellers typically used in high-pressure applications. Extensive research has been performed to define diffuser stall limits for this family of stages: three impellers characterized by different blade-outlet-width-to-impeller-radius-ratios have been tested with different diffuser configurations (different pinch shapes, diffuser widths and diffusion ratios). The basic configuration comprises a 1:1 geometrical scale stage with a return channel upstream, a 2D impeller with a vaneless diffuser and a volute with a constant cross sectional area downstream. Several diffuser types with different widths and diffusion ratios were tested. Detailed experimental results have been reported in previous works [1, 2, 3 and 4]. In this paper experimental data are reviewed in order to analyze impeller influence on diffuser stability and to develop some summarizing consideration on stall behavior of vaneless diffuser for impeller with low blade-outlet-width-to-impeller-radius-ratio.

scholarly journals Estimation of the Aerodynamic Force Induced by Vaneless Diffuser Rotating Stall in Centrifugal Compressor Stages

2016 ◽  
Vol 101 ◽  
pp. 734-741 ◽  
Author(s):  
Michele Marconcini ◽  
Alessandro Bianchini ◽  
Matteo Checcucci ◽  
Davide Biliotti ◽  
Marco Giachi ◽  
...  
Keyword(s):  
Centrifugal Compressor ◽  
Aerodynamic Force ◽  
Rotating Stall ◽  
Vaneless Diffuser

Experimental Investigation and Characterization of the Rotating Stall in a High Pressure Centrifugal Compressor: Part III — Influence of Diffuser Geometry on Stall Inception and Performance (2nd Impeller Tested)

2003 ◽  
Author(s):  
A. Cellai ◽  
G. Ferrara ◽  
L. Ferrari ◽  
C. P. Mengoni ◽  
L. Baldassarre
Keyword(s):  
High Pressure ◽  
Rotating Stall ◽  
Point Of View ◽  
Vaneless Diffuser ◽  
Cross Sectional ◽  
Stall Inception ◽  
Last Stage ◽  
Return Channel ◽  
And Performance ◽  
Geometrical Scale

Vaneless diffuser rotating stall is a serious problem for centrifugal compressors since it limits their working range. In particular the last stage seems to be the most critical from this point of view. In the literature some good correlations can be found for predicting stall inception but they hardly cover the case of last stage configuration, especially for very low blade-outlet-width-to-impeller-radius-ratio impellers typically used in high-pressure applications. Extensive research has been planned to define diffuser stall limits for this family of stages: three impellers characterized by different blade-outlet-width-to-impeller-radius-ratios are tested. The basic configuration comprises a 1:1 geometrical scale stage with a return channel upstream, a 2D impeller with a vaneless diffuser and a volute with a constant cross sectional area downstream. Several diffuser types with different widths, pinch shapes and diffusion ratios were tested. The results for the first impeller have already been reported in part I and II. In this part the effects of the above mentioned geometric parameter changes on stage stability and performance are presented with respect to the second impeller.

Experimental Investigation and Performance Analysis of Six Low Flow Coefficient Centrifugal Compressor Stages

1995 ◽  
Vol 117 (4) ◽  
pp. 585-592 ◽  
Author(s):  
J. Paroubek ◽  
V. Cyrus ◽  
J. Kyncˇl
Keyword(s):  
Development Program ◽  
Rotating Stall ◽  
Flow Coefficient ◽  
Low Flow ◽  
Vaneless Diffuser ◽  
Test Rig ◽  
Disk Friction ◽  
Return Channel ◽  
And Performance ◽  
Low Flow Coefficient

Some results of a research and development program for centrifugal compressors are presented. Six-stage configurations with low flow coefficient were tested. The stages had channel width parameter b2/D2 = 0.01 and 0.03. For each value of the width parameter, three different impellers with inlet hub to outlet diameter ratio do/D2 = 0.3, 0.4, and 0.5 were designed. Test rig, instrumentation, and data analysis are described. Special attention was devoted to probe calibrations and to evaluation of the leakage, bearing, and disk friction losses. Aerodynamic performance of all tested stages is presented. Slip factors of impellers obtained experimentally and theoretically are compared. Losses in both vaneless diffuser and return channel with deswirl vanes are discussed. Rotating stall was also investigated. Criteria for stall limit were tested.

scholarly journals Experimental Investigation and Performance Analysis of Six Low Flow Coefficient Centrifugal Compressor Stages

1994 ◽  
Author(s):  
J. Paroubek ◽  
V. Cyrus ◽  
J. Kyncl
Keyword(s):  
Rotating Stall ◽  
Development Programme ◽  
Diameter Ratio ◽  
Flow Coefficient ◽  
Low Flow ◽  
Vaneless Diffuser ◽  
Test Rig ◽  
Return Channel ◽  
And Performance ◽  
Low Flow Coefficient

Some results of a research and development programme for centrifugal compressors are presented. Six stage configurations with low flow coefficient were tested. The stages had channel width parameter bo/D2=0.01 and 0.03. For each value of the width parameter three different impellers with inlet hub to outlet diameter ratio do/D2=0.3, 0.4 and 0.5 were designed. Test rig, instrumentation and data analysis are described. Special attention was devoted to probe calibrations and to evaluation of the leakage, bearing and disc friction losses. Aerodynamic performance of all tested stages is presented. Slip factors of impellers obtained experimentally and theoretically are compared. Losses in both vaneless diffuser and return channel with de-swirl vanes are discussed. Rotating stall was also investigated. Criteria for stall limit were tested.

A Systematic Approach to Estimate the Impact of the Aerodynamic Force Induced by Rotating Stall in a Vaneless Diffuser on the Rotordynamic Behavior of Centrifugal Compressors

2013 ◽  
Author(s):  
Alessandro Bianchini ◽  
Davide Biliotti ◽  
Giovanni Ferrara ◽  
Lorenzo Ferrari ◽  
Elisabetta Belardini ◽  
...  
Keyword(s):  
Aerodynamic Force ◽  
Dynamic Pressure ◽  
Journal Bearings ◽  
Rotating Stall ◽  
Squeeze Film ◽  
Accurate Estimation ◽  
Vaneless Diffuser ◽  
Test Rig ◽  
Centrifugal Compressors ◽  
The Impact

One of the main challenges of the present industrial research on centrifugal compressors is the need of extending the left margin of the operating range of the machines. As a result, interest is being paid in accurately evaluating the amplitude of the pressure fluctuations caused by rotating stall, which usually occurs prior to surge. The related aerodynamic force acting on the rotor can produce subsynchronous vibrations, which can prevent the machine to further operate, in case their amplitude is too high. These vibrations are often contained thanks to the stiffness of the oil journals. Centrifugal compressors design is, however, going towards alternative journal solutions having lower stiffness levels (e.g. Active Magnetic Bearings or Squeeze Film Dampers), which hence will be more sensitive to this kind of excitation: consequently, a more accurate estimation of the expected forces in presence of dynamic external forces like those connected to an aerodynamically unstable condition is needed to predict the vibration level and the compressor operability in similar conditions. Within this scenario, experimental tests were carried out on an industrial impeller operating at high peripheral Mach number. The dedicated test rig was equipped with several dynamic pressure probes that were inserted in the gas flow path; moreover, the rotor vibrations were constantly monitored with typical vibration probes located near the journal bearings. The pressure field induced by the rotating stall in the vaneless diffuser was reconstructed by means of an ensemble average approach, defining the amplitude and frequency of the external force acting on the impeller. The calculated force value was then included in the rotordynamic model of the test rig: the predicted vibrations on the bearings were compared with the measurements, showing satisfactory agreement. Finally, the prospects of the proposed approach are discussed by investigating the response of a real machine in high-pressure functioning when different choices of journal bearings are made.

Experimental Analysis of the Pressure Field Inside a Vaneless Diffuser From Rotating Stall Inception to Surge

2015 ◽  
Author(s):  
Alessandro Bianchini ◽  
Davide Biliotti ◽  
Dante Tommaso Rubino ◽  
Lorenzo Ferrari ◽  
Giovanni Ferrara
Keyword(s):  
Transient Analysis ◽  
Pressure Field ◽  
Dynamic Pressure ◽  
Rotating Stall ◽  
Accurate Estimation ◽  
Vaneless Diffuser ◽  
Ensemble Averaging ◽  
Stall Inception ◽  
Key Points ◽  
Real Time Visualization

An accurate estimation of rotating stall is one of the key points for high-pressure centrifugal compressors, as it is often connected with the onset of detrimental subsynchronous vibrations which can prevent the machine from operating beyond this limit. With particular reference to vaneless diffuser rotating stall, the most common practice in industrial machines is to make use of a limited number of dynamic pressure probes to reconstruct the stall characteristics after an ensemble averaging approach. In this study, a 1:1 model of an industrial compressor stage was tested in a dedicated test rig and equipped with 24 pressure probes properly distributed along the diffuser circumference with the scope of providing a real-time visualization of the spatial pressure distribution within the diffuser. The results allowed the assessment of some important characteristics of the stall cells that were historically supposed based on averaged data, e.g. the cells rigidity. Moreover, the present study confirmed the existence of a stall pattern with two almost axisymmetric lobes. Finally, the transient analysis of both the stall inception and the surge onset was carried out, highlighting the flow field evolution in the diffuser under these conditions.

Sign in / Sign up

Export Citation Format

Share Document