Experimental Investigation of the Unsteady Tip Clearance Flow in a Low-Speed Axial Contra-Rotating Compressor

2018 ◽  
Author(s):  
Shaoyuan Yue ◽  
Yangang Wang ◽  
Liguo Wei ◽  
Hao Wang ◽  
Shuanghou Deng
Keyword(s):  
Correlation Analysis ◽  
Dynamic Pressure ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Tip Clearance Flow ◽  
Cross Correlation Analysis ◽  
Clearance Flow ◽  
Tip Clearance Vortex

This paper experimentally investigated the evolution of the tip clearance flow of a CRAC (Contra-Rotating Axial Compressor) test rig by means of high-response dynamic pressure measurements. The unsteady pressure field along both chordwise and circumferential directions in the tip clearance is recorded. The tip clearance vortex trajectory is captured using RMS (Root-Mean Square) method. Pressure spectrum analysis indicates that the unsteadiness of tip clearance vortex occurred when the flow coefficient approaches low enough even in the stable operating point. The unsteadiness of tip clearance vortex gets stronger as the flow coefficient drops until rotating stall occurs. According to this feature, the auto-correlation analysis and the cross-correlation analysis combined probability statistics method are used to work as pre-stall warning methods. In addition to, rotating instability which is caused by disturbances propagating along circumferential direction occurred at some flow condition.

Short Length-Scale Rotating Stall Inception in a Transonic Axial Compressor: Criteria and Mechanisms

2006 ◽  
Author(s):  
Chunill Hah ◽  
Jo¨rg Bergner ◽  
Heinz-Peter Schiffer
Keyword(s):  
Axial Compressor ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Transonic Compressor ◽  
Eddy Simulation ◽  
Clearance Flow ◽  
Flow Mechanisms ◽  
Tip Clearance Vortex

The current paper reports on investigations aimed at advancing the understanding of the flow mechanism that leads to the onset of short-length scale rotating stall in a transonic axial compressor. Experimental data show large oscillation of the tip clearance vortex as the rotor operates near the stall condition. Inception of spike-type rotating stall is also measured in the current transonic compressor with high response pressure transducers. Computational studies of a single passage and the full annulus were carried out to identify flow mechanisms behind the spike-type stall inception in the current transonic compressor rotor. Steady and unsteady single passage flow simulations were performed, first to get insight into the interaction between the tip clearance vortex and the passage shock. The conventional Reynolds-averaged Navier-Stokes method with a standard turbulence closure scheme does not accurately reproduce tip clearance vortex oscillation and the measured unsteady pressure field. Consequently, a Large Eddy Simulation (LES) was carried out to capture more relevant physics in the computational simulation of the rotating stall inception. The unsteady random behavior of the tip clearance vortex and it’s interaction with the passage shock seem to be critical ingredients in the development of spike-type rotating stall in a transonic compressor. The Large Eddy Simulation was further extended to the full annulus to identify flow mechanisms behind the measured spike-type rotating stall inception. The current study shows that the spike-type rotating stall develops after the passage shock is fully detached from the blade passages. Interaction between the tip clearance vortex and the passage shock creates a low momentum area near the pressure side of the blade. As the mass flow rate decreases, this low momentum area moves further upstream and reversed tip clearance flow is initiated at the trailing edge plane. Eventually, the low momentum area near the pressure side reaches the leading edge and forward spillage of the tip clearance flow occurs. The flows in the affected blade passage or passages then stall. As the stalled blade passages are formed behind the passage shock, the stalled area rotates counter to the blade rotation just like the classical Emmon’s type rotating stall. Both the measurements and the computations show that the rotating stall cell covers one to two blade passage lengths and rotates at roughly 50% of the rotor speed.

Investigation of Unsteady Flow Field in a Low-Speed One and a Half Stage Axial Compressor: Effects of Tip Gap Size on the Tip Clearance Flow Structure at Near Stall Operation

2014 ◽  
Author(s):  
Chunill Hah ◽  
Michael Hathaway ◽  
Joseph Katz
Keyword(s):  
Unsteady Flow ◽  
Flow Structure ◽  
Flow Instability ◽  
Axial Compressor ◽  
Leading Edge ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Low Speed ◽  
Clearance Flow ◽  
Tip Clearance Vortex

The primary focus of this paper is to investigate the effect of rotor tip gap size on how the rotor unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor at near stall operation (for example, where maximum pressure rise is obtained). A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at this flow condition with both a small and a large tip gaps. The numerically obtained flow fields at the small clearance matches fairly well with the available initial measurements obtained at the Johns Hopkins University with 3-D unsteady PIV in an index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. The numerical results are also compared with previously published measurements in a low speed single stage compressor (Maerz et al. [2002]). The current study shows that, with the smaller rotor tip gap, the tip clearance vortex moves to the leading edge plane at near stall operating condition, creating a nearly circumferentially aligned vortex that persists around the entire rotor. On the other hand, with a large tip gap, the clearance vortex stays inside the blade passage at near stall operation. With the large tip gap, flow instability and related large pressure fluctuation at the leading edge are observed in this one and a half stage compressor. Detailed examination of the unsteady flow structure in this compressor stage reveals that the flow instability is due to shed vortices near the leading edge, and not due to a three-dimensional separation vortex originating from the suction side of the blade, which is commonly referred to during a spike-type stall inception. The entire tip clearance flow is highly unsteady. Many vortex structures in the tip clearance flow, including the sheet vortex system near the casing, interact with each other. The core tip clearance vortex, which is formed with the rotor tip gap flows near the leading edge, is also highly unsteady or intermittent due to pressure oscillations near the leading edge and varies from passage to passage. For the current compressor stage, the evidence does not seem to support that a classical vortex breakup occurs in any organized way, even with the large tip gap. Although wakes from the IGV influence the tip clearance flow in the rotor, the major characteristics of rotor tip clearance flows in isolated or single stage rotors are observed in this one and a half stage axial compressor.

scholarly journals Investigation of Unsteady Tip Clearance Flow in a Low-Speed One and Half Stage Axial Compressor With LES and PIV

2015 ◽  
Author(s):  
Chunill Hah ◽  
Michael Hathaway ◽  
Joseph Katz ◽  
David Tan
Keyword(s):  
Axial Compressor ◽  
Suction Side ◽  
Flow Fields ◽  
Tip Clearance ◽  
Gap Size ◽  
Tip Clearance Flow ◽  
Gap Flow ◽  
Clearance Flow ◽  
Single Structure ◽  
Tip Clearance Vortex

The primary focus of this paper is to investigate how a rotor’s unsteady tip clearance flow structure changes in a low speed one and half stage axial compressor when the rotor tip gap size is increased from 0.5 mm (0.49% of rotor tip blade chord, 2% of blade span) to 2.4 mm (2.34% chord, 4% span) at the design condition are investigated. The changes in unsteady tip clearance flow with the 0.62 % tip gap as the flow rate is reduced to near stall condition are also investigated. A Large Eddy Simulation (LES) is applied to calculate the unsteady flow field at these three flow conditions. Detailed Stereoscopic PIV (SPIV) measurements of the current flow fields were also performed at the Johns Hopkins University in a refractive index-matched test facility which renders the compressor blades and casing optically transparent. With this setup, the unsteady velocity field in the entire flow domain, including the flow inside the tip gap, can be measured. Unsteady tip clearance flow fields from LES are compared with the PIV measurements and both LES and PIV results are used to study changes in tip clearance flow structures. The current study shows that the tip clearance vortex is not a single structure as traditionally perceived. The tip clearance vortex is formed by multiple interlaced vorticities. Therefore, the tip clearance vortex is inherently unsteady. The multiple interlaced vortices never roll up to form a single structure. When phased-averaged, the tip clearance vortex appears as a single structure. When flow rate is reduced with the same tip gap, the tip clearance vortex rolls further upstream and the tip clearance vortex moves further radially inward and away from the suction side of the blade. When the tip gap size is increased at the design flow condition, the overall tip clearance vortex becomes stronger and it stays closer to the blade suction side and the vortex core extends all the way to the exit of the blade passage. Measured and calculated unsteady flow fields inside the tip gap agree fairly well. Instantaneous velocity vectors inside the tip gap from both the PIV and LES do show flow separation and reattachment at the entrance of tip gap as some earlier studies suggested. This area at the entrance of tip gap flow (the pressure side of the blade) is confined very close to the rotor tip section. With a small tip gap (0.5mm), the gap flow looks like a simple two-dimensional channel flow with larger velocity near the casing for both flow rates. A small area with a sharp velocity gradient is observed just above the rotor tip. This strong shear layer is turned radially inward when it collides with the incoming flow and forms the core structure of the tip clearance vortex. When tip gap size is increased to 2.4 mm at the design operation, the radial profile of the tip gap flow changes drastically. With the large tip gap, the gap flow looks like a two-dimensional channel flow only near the casing. Near the rotor top section, a bigger region with very large shear and reversed flow is observed.

Criteria for Spike Initiated Rotating Stall

2008 ◽  
Vol 130 (1) ◽  
Author(s):  
Huu Duc Vo ◽  
Choon S. Tan ◽  
Edward M. Greitzer
Keyword(s):  
Computational Study ◽  
Axial Compressor ◽  
Leading Edge ◽  
Rotating Stall ◽  
Short Length ◽  
Tip Clearance ◽  
Length Scale ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Clearance Flow

A computational study to define the phenomena that lead to the onset of short length-scale (spike) rotating stall disturbances has been carried out. Based on unsteady simulations, we hypothesize there are two conditions necessary for the formation of spike disturbances, both of which are linked to the tip clearance flow. One is that the interface between the tip clearance and oncoming flows becomes parallel to the leading-edge plane. The second is the initiation of backflow, stemming from the fluid in adjacent passages, at the trailing-edge plane. The two criteria also imply a circumferential length scale for spike disturbances. The hypothesis and scenario developed are consistent with numerical simulations and experimental observations of axial compressor stall inception. A comparison of calculations for multiple blades with those for single passages also allows statements to be made about the utility of single passage computations as a descriptor of compressor stall.

An Experimental and Computational Investigation of Tip Clearance Flow and Its Impact on Stall Inception

2010 ◽  
Author(s):  
Matthew A. Bennington ◽  
Mark H. Ross ◽  
Joshua D. Cameron ◽  
Scott C. Morris ◽  
Juan Du ◽  
...  
Keyword(s):  
Axial Compressor ◽  
Axial Flow ◽  
Leading Edge ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Momentum Balance ◽  
Tip Leakage Flow ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Clearance Flow

A numerical and experimental study was conducted to investigate the tip clearance flow and its relationship to stall in a transonic axial compressor. The CFD results were used to identify the existence of an interface between incoming axial flow and the reverse tip clearance flow. A surface streaking method was used to experimentally identify this interface as a line of zero axial shear stress at the casing. The position of this line, denoted xzs, moved upstream with decreasing flow coefficient in both the experiments and computations. The line was found to be at the rotor leading edge plane when the compressor stalled. Further measurements using rotor offset and inlet distortion further corroborated these results, and demonstrated that the movement of the interface upstream of the leading edge leads to the generation of rotating (“spike”) disturbances. Stall was therefore interpreted to occur as a result of a critical momentum balance between the approach fluid and the tip-leakage flow.

Short Length-Scale Rotating Stall Inception in a Transonic Axial Compressor: Experimental Investigation

2006 ◽  
Author(s):  
Jo¨rg Bergner ◽  
Matthias Kinzel ◽  
Heinz-Peter Schiffer ◽  
Chunill Hah
Keyword(s):  
Experimental Investigation ◽  
Axial Compressor ◽  
Rotating Stall ◽  
Wall Pressure ◽  
Tip Clearance ◽  
Stall Inception ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
Contour Plots ◽  
Transonic Axial Compressor

To improve the understanding of spike-type stall inception of a transonic axial compressor, measurements of the unsteady static pressure in the rotor endwall region are analyzed. At design speed, a detailed experimental investigation of the unsteadiness of the pressure field at the rotor endwall at near stall condition shows a strong fluctuation of the tip clearance flow. Both vortex strength and -trajectory oscillate randomly. Analysis of the wall pressure time histories during stall inception suggests that spike-type disturbances of the flow field correlate with an upstream motion of one blade passages shock front. In addition, the evolution of a stall cell could be visualized by means of static wall-pressure contour plots.

On Improving the Surge Margin of a Tip-Critical Axial Compressor Rotor

2017 ◽  
Author(s):  
Marcus Lejon ◽  
Tomas Grönstedt ◽  
Niklas Andersson ◽  
Lars Ellbrant ◽  
Hans Mårtensson
Keyword(s):  
Axial Compressor ◽  
Tip Clearance ◽  
Flow Coefficient ◽  
Incoming Flow ◽  
Objective Functions ◽  
Blade Loading ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Surge Margin ◽  
Clearance Flow

Delaying breakdown of the flow in the tip region of a tip-critical compressor rotor as long as possible, i.e. improving the surge margin, is of great interest to the turbomachinery community and is the focus of this study. The surge margin of ten compressor rotors is evaluated numerically, each with different blade loading and geometry at the tip. Previous work in the field has shown the dependence of an interface in the tip region of a compressor rotor between the incoming flow and the tip clearance flow with the passage flow coefficient ϕ. Previous work in the field has also shown that a higher incoming meridional momentum in the tip region can be beneficial to the surge margin of a tip-critical rotor. The present study generalizes these findings by taking into account the local blade loading of the rotor tip section and the level of loss in the tip region. The surge margin is found to improve if the blade loading of the rotor tip section is increased, which acts to increase the incoming mass flow rate and improve the surge margin provided that an increase in loss, mainly related to the strength and direction of the tip clearance flow, does not negate the effect as the compressor is throttled. Two quantities are proposed as objective functions to be used for optimization to achieve a compressor rotor with high surge margin based on the flow field at the design point. Finally, an optimization and analysis of the results is made to demonstrate the proposed objective functions in practise.

3-D Digital PIV Measurements of the Tip Clearance Flow in an Axial Compressor

2002 ◽  
Author(s):  
Mark P. Wernet ◽  
Dale Van Zante ◽  
Tony J. Strazisar ◽  
W. Trevor John ◽  
P. Susan Prahst
Keyword(s):  
Three Dimensional ◽  
Axial Compressor ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Image Velocimetry ◽  
Clearance Flow ◽  
Compressor Performance ◽  
Tip Clearance Vortex

The accurate characterization and simulation of rotor tip clearance flows has received much attention in recent years due to their impact on compressor-performance and stability. At NASA Glenn the first known three dimensional Digital Particle Image Velocimetry (DPIV) measurements of the tip region of a low speed compressor rotor have been acquired to characterize the behavior of the rotor tip clearance flow. The measurements were acquired phase-locked to the rotor position so that changes in the tip clearance vortex position relative to the rotor blade can be seen. The DPIV technique allows the magnitude and relative contributions of both the asynchronous motions of a coherent structure and the temporal unsteadiness to be evaluated. Comparison of measurements taken at the peak efficiency and at near stall operating conditions characterizes the mean position of the clearance vortex and the changes in the unsteady behavior of the vortex with blade loading. Comparisons of the 3-D DPIV measurements at the compressor design point to a 3D steady N-S solution are also done to assess the fidelity of steady, single-passage simulations to model an unsteady flow field.

Experimental Off-Design Investigation of Unsteady Secondary Flow Phenomena in a Three-Stage Axial Compressor at 68% Nominal Speed

2004 ◽  
Author(s):  
Andreas Bohne ◽  
Reinhard Niehuis
Keyword(s):  
Dynamic Pressure ◽  
Axial Compressor ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Pressure Transducers ◽  
Surge Margin ◽  
Clearance Flow ◽  
Flow Phenomena

This paper deals with unsteady measurements in a highspeed three-stage axial compressor with inlet guide vanes (IGV) and controlled diffusion airfoils (CDA) at off-design conditions. The compressor under consideration exhibits design features of real industrial compressors. The main emphasis is put on the experimental investigation of two operating points at 68% nominal speed where a significant mismatching of the stages occurs. The first operating point is the last stable one near the surge margin whereas the second one represents choke. Probe traverses with a high resolution both in space and time show the significant potential upstream influence of the rotor blades. This effect and the disturbances caused by the convected wakes do strongly influence the unsteady boundary layer behaviour of the stator blades which are detected by glue-on hot-film sensors at different spanwise positions. Dynamic pressure transducers on the casing show that the structure of the rotor tip clearance flow strongly depends on the operating conditions of the compressor. Conclusions can be drawn concerning the consideration of the discussed unsteady effects within the design process of multistage axial compressors with respect to the presented results.

scholarly journals Pre-Stall Behavior of a Transonic Axial Compressor Stage via Time-Accurate Numerical Simulation

2007 ◽  
Author(s):  
Jen-Ping Chen ◽  
Michael D. Hathaway ◽  
Gregory P. Herrick
Keyword(s):  
High Performance ◽  
Axial Compressor ◽  
Pressure Rise ◽  
Axial Direction ◽  
Rotating Stall ◽  
Tip Clearance ◽  
Compressor Stage ◽  
Tip Clearance Flow ◽  
Transonic Compressor ◽  
Clearance Flow

CFD calculations using high-performance parallel computing were conducted to simulate the pre-stall flow of a transonic compressor stage, NASA compressor Stage 35. The simulations were run with a full-annulus grid that models the 3-D, viscous, unsteady blade row interaction without the need for an artificial inlet distortion to induce stall. The simulation demonstrates the development of the rotating stall from the growth of instabilities. Pressure-rise performance and pressure traces are compared with published experimental data before launching a detailed study of the flow evolution prior to the rotating stall. Spatial FFT analysis of the flow indicates a rotating long-length disturbance of one rotor circumference, which is followed by a spike-type breakdown. The analysis also links the long-length wave disturbance with the initiation of the spike inception. The spike instabilities occur when the trajectory of the tip clearance flow becomes vertical to the axial direction. When approaching to stall, the passage shock changes from a single oblique shock to a dual-shock, which distorts the vertical trajectory of the tip clearance vortex but shows no evidence to cause flow separation that may contribute to stall.

Sign in / Sign up

Export Citation Format

Share Document