scholarly journals Numerical Investigation Into the Impact of Injector Geometrical Design Parameters on Hydrogen Micromix Combustion Characteristics

2020 ◽  
Author(s):  
Xiaoxiao Sun ◽  
Parash Agarwal ◽  
Francesco Carbonara ◽  
David Abbott ◽  
Pierre Gauthier ◽  
...  
Keyword(s):  
Gas Turbines ◽  
Momentum Flux ◽  
Flux Ratio ◽  
Injection System ◽  
Design Parameters ◽  
Gas Temperature ◽  
Geometrical Design ◽  
Momentum Flux Ratio ◽  
Mixing Characteristics ◽  
The Impact

Abstract Hydrogen micromix combustion is a promising concept to reduce the environmental impact of both aero and land-based gas turbines by delivering carbon-free and ultra-low-NOx combustion without the risk of autoignition or flashback. As a part of the ENABLEH2 project, the current study focuses on the influence of design parameters on the micromix hydrogen combustion injectors. This study provides deeper insights into the design space of a hydrogen micromix injection system via numerical simulations. The key geometrical design parameters of the micromix combustion system are the sizing of the air gates and the hydrogen injector orifices together with the offset distance between air gate and hydrogen injection, the mixing distance and the injector to injector spacing. This paper first presents results of the numerical simulation of four designs, down selected from a series of combinations of the key design parameters, including cases with low and high momentum flux ratio, weak and strong flame-flame interaction. It was discovered that the hydrogen/air mixing characteristics, and flame to flame interactions, are the main factors influencing the combustor gas temperature distributions, flame lengths and the corresponding NOx production. The current study then focused on the effect of air gate geometry on the mixing characteristics, flame shape and temperature distribution. The momentum flux ratio was kept constant throughout this investigation by keeping the air gate area constant. Variations of the original baseline air gate design were studied, followed by a study of various novel air gate geometries, including circular, semi-circular and elliptical shapes. It is concluded that NOx production is influenced by a number of factors including jet penetration flame interactions and air gate shape and that there is a “Sweet Spot” that results in the lowest practicable NOx production. Flatter and wider air gate shapes tend to yield the lowest temperature and consequently the lowest NOx. Reduced interaction between flames also tends to reduce NOx and by manipulating hydrogen penetration, there is the potential to further reduce the NOx production.

Impact of Operating Conditions and Design Parameters on Gas Turbine Hot Section Creep Life

2010 ◽  
Author(s):  
S. Eshati ◽  
M. F. Abdul Ghafir ◽  
P. Laskaridis ◽  
Y. G. Li
Keyword(s):  
Gas Turbines ◽  
Performance Model ◽  
Operating Conditions ◽  
Creep Model ◽  
Design Parameters ◽  
Gas Temperature ◽  
Creep Life ◽  
Cooling Effectiveness ◽  
Radial Temperature ◽  
The Impact

This paper investigates the relationship between design parameters and creep life consumption of stationary gas turbines using a physics based life model. A representative thermodynamic performance model is used to simulate engine performance. The output from the performance model is used as an input to the physics based model. The model consists of blade sizing model which sizes the HPT blade using the constant nozzle method, mechanical stress model which performs the stress analysis, thermal model which performs thermal analysis by considering the radial distribution of gas temperature, and creep model which using the Larson-miller parameter to calculate the lowest blade creep life. The effect of different parameters including radial temperature distortion factor (RTDF), material properties, cooling effectiveness and turbine entry temperatures (TET) is investigated. The results show that different design parameter combined with a change in operating conditions can significantly affect the creep life of the HPT blade and the location along the span of the blade where the failure could occur. Using lower RTDF the lowest creep life is located at the lower section of the span, whereas at higher RTDF the lowest creep life is located at the upper side of the span. It also shows that at different cooling effectiveness and TET for both materials the lowest blade creep life is located between the mid and the tip of the span. The physics based model was found to be simple and useful tool to investigate the impact of the above parameters on creep life.

scholarly journals Theory of Non-Dimensional Groups in Film Effectiveness Studies

2020 ◽  
Vol 142 (4) ◽  
Author(s):  
Francesco Ornano ◽  
Thomas Povey
Keyword(s):  
Heat Capacity ◽  
Physical Interpretation ◽  
Film Cooling ◽  
Gas Turbines ◽  
Momentum Flux ◽  
Density Ratio ◽  
Flux Ratio ◽  
Cooling Performance ◽  
Momentum Flux Ratio ◽  
Blowing Ratio

Abstract The desire to improve gas turbines has led to a significant body of research concerning film cooling optimization. The open literature contains many studies considering the impact on film cooling performance of both geometrical factors (hole shape, hole separation, hole inclination, row separation, etc.) and physical influences (effect of density ratio (DR), momentum flux ratio, etc.). Film cooling performance (typically film effectiveness, under either adiabatic or diabatic conditions) is almost universally presented as a function of one or more of three commonly used non-dimensional groups: blowing—or local mass flux—ratio, density ratio, and momentum flux ratio. Despite the abundance of papers in this field, there is some confusion in the literature about the best way of presenting such data. Indeed, the very existence of a discussion on this topic points to lack of clarity. In fact, the three non-dimensional groups in common use (blowing ratio (BR), density ratio, and momentum flux ratio) are not entirely independent of each other making aspects of this discussion rather meaningless, and there is at least one further independent group of significance that is rarely discussed in the literature (specific heat capacity flux ratio). The purpose of this paper is to bring clarity to this issue of correct scaling of film cooling data. We show that the film effectiveness is a function of 11 (additional) non-dimensional groups. Of these, seven can be regarded as boundary conditions for the main flow path and should be matched where complete similarity is required. The remaining four non-dimensional groups relate specifically to the introduction of film cooling. These can be cast in numerous ways, but we show that the following forms allow clear physical interpretation: the momentum flux ratio, the blowing ratio, the temperature ratio (TR), and the heat capacity flux ratio. Two of these parameters are in common use, a third is rarely discussed, and the fourth is not discussed in the literature. To understand the physical mechanisms that lead to each of these groups being independently important for scaling, we isolate the contribution of each to the overall thermal field with a parametric numerical study using 3D Reynolds-averaged Navier–Stokes (RANS) and large eddy simulations (LES). The results and physical interpretation are discussed.

Numerical Study on Analogy Principle of Overall Cooling Effectiveness in Engine and Laboratory Condition

2018 ◽  
Author(s):  
Gang Xie ◽  
Cun-liang Liu ◽  
Lin Ye ◽  
Rui Wang
Keyword(s):  
Heat Transfer ◽  
Laboratory Condition ◽  
Biot Number ◽  
Gas Turbines ◽  
Momentum Flux ◽  
Flux Ratio ◽  
Temperature Ratio ◽  
Cooling Effectiveness ◽  
Momentum Flux Ratio ◽  
Engine Condition

The overall cooling effectiveness, which represents the distribution of dimensionless temperature on gas turbines surface, is an important parameter for conjugate heat transfer analysis of gas turbines. Generally, it is difficult to measure the overall cooling effectiveness in engine condition. However, the overall cooling effectiveness can be measured in the laboratory by matching the appropriate parameters to those of the actual turbine blade. Thus, it is important to evaluate the key parameters of matching methods. In this paper, the effects of adiabatic film effectiveness and Biot number on the overall cooling effectiveness were investigated with an impingement/effusion model by numerical simulation, in which 3-D steady RANS approach with the k–ω SST turbulence model were used. The tested plate had 8 cylinder hole rows of 30 degree inclined angle, and the internal cooling employed staggered array jet impingements. The matching performance was evaluated by comparing the results in both typical engine condition and laboratory condition. The analogy principles were discussed in detail, the results showed that the overall cooling effectiveness can be matched by using different matching principles in different lab condition. The theoretical analysis was verified by numerical results. The distribution and values of overall cooling effectiveness can be matched well between engine condition and lab condition by matching both temperature ratio, mainstream side Biot number and blowing ratio. If the temperature ratio is mismatched, the momentum flux ratio will be an important parameter for overall cooling effectiveness. Matching momentum flux ratio will reduce the difference of the adiabatic cooling effectiveness and heat transfer ratio between engine condition and laboratory condition.

Volumetric Velocimetry Measurements of Film Cooling Jets

2018 ◽  
Vol 141 (3) ◽  
Author(s):  
Artur Joao Carvalho Figueiredo ◽  
Robin Jones ◽  
Oliver J. Pountney ◽  
James A. Scobie ◽  
Gary D. Lock ◽  
...  
Keyword(s):  
Film Cooling ◽  
Momentum Flux ◽  
Three Dimensional ◽  
Flux Ratio ◽  
Quality Data ◽  
Data Set ◽  
Momentum Flux Ratio ◽  
Jet In Crossflow ◽  
Lift Off ◽  
Induced Velocity

This paper presents volumetric velocimetry (VV) measurements for a jet in crossflow that is representative of film cooling. VV employs particle tracking to nonintrusively extract all three components of velocity in a three-dimensional volume. This is its first use in a film-cooling context. The primary research objective was to develop this novel measurement technique for turbomachinery applications, while collecting a high-quality data set that can improve the understanding of the flow structure of the cooling jet. A new facility was designed and manufactured for this study with emphasis on optical access and controlled boundary conditions. For a range of momentum flux ratios from 0.65 to 6.5, the measurements clearly show the penetration of the cooling jet into the freestream, the formation of kidney-shaped vortices, and entrainment of main flow into the jet. The results are compared to published studies using different experimental techniques, with good agreement. Further quantitative analysis of the location of the kidney vortices demonstrates their lift off from the wall and increasing lateral separation with increasing momentum flux ratio. The lateral divergence correlates very well with the self-induced velocity created by the wall–vortex interaction. Circulation measurements quantify the initial roll up and decay of the kidney vortices and show that the point of maximum circulation moves downstream with increasing momentum flux ratio. The potential for nonintrusive VV measurements in turbomachinery flow has been clearly demonstrated.

scholarly journals Drop Size Characteristics of Forward Angled Injectors in Subsonic Cross Flows

2013 ◽  
Author(s):  
Venkat S. Iyengar ◽  
Sathiyamoorthy Kumarasamy ◽  
Srinivas Jangam ◽  
Manjunath Pulumathi
Keyword(s):  
Gas Turbine ◽  
Test Section ◽  
Momentum Flux ◽  
Drop Size ◽  
Cross Flow ◽  
Flux Ratio ◽  
Liquid Jet ◽  
Axial Distance ◽  
Momentum Flux Ratio ◽  
Spray Plume

Cross flow fuel injection is a widely used approach for injecting liquid fuel in gas turbine combustors and afterburners due to the higher penetration and rapid mixing of fuel and the cross flowing airstream. Because of the very limited residence time available in these combustors it is essential to ensure that smaller drop sizes are generated within a short axial distance from the injector in order to promote effective mixing. This requirement calls for detailed investigations into spray characteristics of different injector configurations in a cross-flow environment for identifying promising configurations. The drop size characteristics of a liquid jet issuing from a forward angled injector into a cross-flow of air were investigated experimentally at conditions relevant to gas turbine afterburners. A rig was designed and fabricated to investigate the injection of liquid jet in subsonic cross-flow with a rectangular test section of cross section measuring 50 mm by 70 mm. Experiments were done with a 10 degree forward angled 0.8 mm diameter plain orifice nozzle which was flush mounted on the bottom plate of test section. Laser diffraction using Malvern Spraytec particle analyzer was used to measure drops size and distributions in the near field of the spray. Measurements were performed at a distance of 70 mm from the injector at various locations along the height of the spray plume for a reasonable range of liquid flow rates as in practical devices. The sprays were characterized using the non dimensional parameters such as the Weber number and the momentum flux ratio and drop sizes were measured at three locations along the height of the spray from the bottom wall. The momentum flux ratio was varied from 5 to 25. Results indicate that with increase in momentum flux ratio the SMD reduced at the specific locations and an higher overall SMD was observed as one goes from the bottom to the top of the spray plume. This was accompanied by a narrowing of the drop size distribution.

Liquid Jets in Subsonic Air Crossflow at Elevated Pressure

2014 ◽  
Vol 137 (4) ◽  
Author(s):  
Jinkwan Song ◽  
Charles Cary Cain ◽  
Jong Guen Lee
Keyword(s):  
Weber Number ◽  
Momentum Flux ◽  
Drop Size ◽  
Density Ratio ◽  
Flux Ratio ◽  
Mie Scattering ◽  
Air Pressure ◽  
Scattering Intensity ◽  
Nozzle Orifice ◽  
Momentum Flux Ratio

The breakup, penetration, droplet size, and size distribution of a Jet A-1 fuel in air crossflow has been investigated with focus given to the impact of surrounding air pressure. Data have been collected by particle Doppler phased analyzer (PDPA), Mie-scattering with high speed photography augmented by laser sheet, and Mie-scattering with intensified charge-coupled device (ICCD) camera augmented by nanopulse lamp. Nozzle orifice diameter, do, was 0.508 mm and nozzle orifice length to diameter ratio, lo/do, was 5.5. Air crossflow velocities ranged from 29.57 to 137.15 m/s, air pressures from 2.07 to 9.65 bar, and temperature held constant at 294.26 K. Fuel flow provides a range of fuel/air momentum flux ratio (q) from 5 to 25 and Weber number from 250 to 1000. From the results, adjusted correlation of the mean drop size has been proposed using drop size data measured by PDPA as follows: (D0/D32)=0.267Wea0.44q0.08(ρl/ρa)0.30(μl/μa)-0.16. This correlation agrees well and shows roles of aerodynamic Weber number, Wea, momentum flux ratio, q, and density ratio, ρl/ρa. Change of the breakup regime map with respect to surrounding air pressure has been observed and revealed that the boundary between each breakup modes can be predicted by a transformed correlation obtained from above correlation. In addition, the spray trajectory for the maximum Mie-scattering intensity at each axial location downstream of injector is extracted from averaged Mie-scattering images. From these results, correlations with the relevant parameters including q, x/do, density ratio, viscosity ratio, and Weber number are made over a range of conditions. According to spray trajectory at the maximum Mie-scattering intensity, the effect of surrounding air pressure becomes more important in the farfield. On the other hand, effect of aerodynamic Weber number is more important in the nearfield.

scholarly journals Effect of excitation on gas centered swirl coaxial injectors

2017 ◽  
Author(s):  
Youngbin Yoon ◽  
Gujeong Park ◽  
Sukil Oh ◽  
Jinhyun Bae
Keyword(s):  
Momentum Flux ◽  
Rocket Engine ◽  
Combustion Instability ◽  
Electrical Conductance ◽  
Flux Ratio ◽  
Xenon Lamp ◽  
Momentum Flux Ratio ◽  
Conductance Method ◽  
Liquid Rocket ◽  
Coaxial Injector

Studies on combustion instability in liquid rocket engines are important in improving combustion efficiency andpreventing combustion chamber losses. To prevent combustion instability, methods such as baffles and cavities are used. The injector is located in the middle of the perturbation-propagation process in the rocket engine, so it is important to study the suppression of combustion instability using the design of the injector. Much research has been focused on the study of liquid excitation in a single injector; however, the actual injector used in a liquid rocket engine is a coaxial injector. In this study, the dynamic characteristics of a gas-centred swirl coaxial injector were investigated by varying the gap thickness and momentum-flux ratio. Spray photographs were captured by synchronizing a stroboscope and digital camera, and a high-speed camera and Xenon lamp were also used. To measure the liquid film, a measurement system was implemented using the electrical conductance method. For excitation of the gas, an acoustic speaker was used to impart a frequency to the gas. The gGas velocity and effect of excitation were measured by hot-wire anemometry. A mechanical pulsator was used for liquid flow excitation. Liquid fluctuation was measured by a dynamic pressure sensor. In both gas and liquid excitation cases, the gain increased as the gap thickness decreased and the momentum-flux ratio increased. From these results, it can be concluded that gap thickness and momentum-flux ratio are major factors in suppressing combustioninstability. DOI: http://dx.doi.org/10.4995/ILASS2017.2017.4653

Prediction of Film Cooling Effectiveness and Heat Transfer due to Streamwise and Compound Angle Injection on Flat Surfaces

1995 ◽  
Author(s):  
S. Neelakantan ◽  
M. E. Crawford
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Momentum Flux ◽  
Flux Ratio ◽  
Equation Model ◽  
Transfer Coefficients ◽  
Film Cooling Effectiveness ◽  
Flat Surfaces ◽  
Momentum Flux Ratio ◽  
Density Ratios

The distributed Yavuzkurt injection model is extended to predict the effectiveness and heat transfer coefficients for film cooling injection from a single row of holes, aligned both along the direction of the freestream and at an angle with it. The injection angles were 24° and 35°. The compound angles considered were 50.5° and 60°. The Yavuzkurt film cooling model is used in conjunction with a one-equation model to yield the effectiveness and heat transfer predictions. The density ratios considered were 1.6 and 0.95 for the effectiveness predictions and 1.0 and 0.95 for the heat transfer predictions. For the effectiveness predictions, the blowing ratios range from 0.5 to 2.5, and the momentum flux ratios from 0.16 until 3.9. The hole spacings were 3, 6, and 7.8 hole diameters. The Yavuzkurt model constants are seen to be definitely correlated with the momentum flux ratio. Correlations for the model constants are obtained in terms of the momentum flux ratio. For the heat transfer predictions, the blowing ratios ranged from 0.4 to 2.0, and the momentum flux ratios from 0.16 to 3.9. The spacing between the holes was 3, 6, and 7.8 hole diameters. The matching between the effectiveness correlations and the heat transfer predictions is done on the basis of the momentum flux ratio. Results indicate that the Yavuzkurt model predictions are best for the in-line round holes. Heat transfer predictions are close to the experimental results for lower blowing ratios, until the ratio exceeds 1. For higher blowing ratios, the predictions, though less accurate, follow the experimental trends.

Experimental Study of Effusion Cooling With Pressure-Sensitive Paint

2017 ◽  
Vol 139 (5) ◽  
Author(s):  
Guanghua Wang ◽  
Gustavo Ledezma ◽  
James DeLancey ◽  
Anquan Wang
Keyword(s):  
Film Cooling ◽  
Gas Turbines ◽  
Cfd Simulation ◽  
Density Ratio ◽  
Open Loop ◽  
Pressure Sensitive Paint ◽  
Gas Temperature ◽  
Eddy Simulation ◽  
Pressure Sensitive ◽  
The Impact

Gas turbines overall efficiency enhancement requires further increasing of the firing temperature and decreasing of cooling flow usage. Multihole (or effusion, or full-coverage) film cooling is widely used for hot gas path components cooling in modern gas turbines. The present study focused on the adiabatic film effectiveness measurement of a round multihole flat-plate coupon. The measurements were conducted in a subsonic open-loop wind tunnel with a generic setup to cover different running conditions. The test conditions were characterized by a constant main flow Mach number of 0.1 with constant gas temperature. Adiabatic film effectiveness was measured by pressure-sensitive paint (PSP) through mass transfer analogy. CO2 was used as the coolant to reach the density ratio of 1.5. Rig computational fluid dynamics (CFD) simulation was conducted to evaluate the impact of inlet boundary layer on testing. Experimental data cover blowing ratios (BRs) at 0.4, 0.6, 0.8, 1.0, and 2.0. Both 2D maps and lateral average profiles clearly indicated that the film effectiveness increases with increasing BR for BR < 0.8 and decreases with increasing BR for BR > 0.8. This observation agreed with coolant jet behavior of single film row, i.e., attached, detached then reattached, and fully detached. PSP data quality was then discussed in detail for validating large eddy simulation.

Sign in / Sign up

Export Citation Format

Share Document