Use of Liquid Film Evaporation in Biporous Media to Achieve High Heat Flux Over Large Areas

2005 ◽  
Author(s):  
Tadej Semenic ◽  
Ying-Yu Lin ◽  
Ivan Catton
Keyword(s):  
Heat Flux ◽  
Test Chamber ◽  
Heat Removal ◽  
High Heat ◽  
Working Fluid ◽  
Interface Temperature ◽  
High Heat Flux ◽  
Film Evaporation ◽  
Powder Diameter ◽  
Better Than

Boiling characteristics of three biporous and one monoporous sintered wick are tested. The monoporous wick has the same wick thickness as a comparable biporous wick. Diameters of the clusters of the comparable biporous wick are equal to the powder diameter of the monoporous wick. A second biporous wick has the same configuration as the first, but is sintered in a thicker layer. The third biporous wick that is tested has smaller cluster sizes then the first two. All three biporous wicks have clusters sintered from powder with the same size distribution. The results demonstrate the advantages of a biporous capillary structure. All biporous wicks reached higher critical heat flux (CHF) then the monoporous wick. Experiments show that larger clusters are better than smaller. Comparing two different wick thicknesses, we can see that even though there is a dryout region inside the thick wick, it is still able to continuously remove heat at constant superheat. No sudden changes in superheat are seen. This process of heat removal is not possible with the thin wick. The working fluid in all runs is methanol. 4-mm thick wick with powder diameter ranging from 53 to 63 microns and cluster diameter ranging from 500 to 707microns is able to remove 377W/cm2 at temperature difference 110°C. A partial pressure inside the test chamber at this heat flux is 0.68atm and the interface temperature 167°C.

Thermal Conductivity and Operating Temperature Effect on the Interline Region in a Micro/Miniature Heat Pipe

2008 ◽  
Author(s):  
Hani H. Sait ◽  
Steve M. Demsky ◽  
HongBin Ma
Keyword(s):  
Thin Film ◽  
Thermal Conductivity ◽  
Heat Flux ◽  
Operating Temperature ◽  
High Heat ◽  
Working Fluid ◽  
High Heat Flux ◽  
Thin Film Evaporation ◽  
Film Evaporation ◽  
Frictional Shear Stress

An analytical model describing thin film evaporation is developed that includes the effects of surface tension, frictional shear stress, wetting characteristics and disjoining pressure. The effects of thermal conductivity of working fluids and operating temperature on the evaporating thin film region are also studied. The results indicate that when the thermal conductivity of the working fluid increases, a high heat flux can be removed from the evaporating thin film region. The operating temperature affects the thin film evaporation. The higher the operating temperature, the more heat flux can be removed from the region. The information of thin film evaporation presented in the paper results in a better understanding of heat transfer mechanism occurring in micro heat pipes.

STABLE, CALM, AND HIGH-HEAT-FLUX HEAT REMOVAL USING A POROUS-MICRO-CHANNEL

2017 ◽  
Author(s):  
Tomio Okawa ◽  
Junki Ohashi ◽  
Ryo Hirata ◽  
Koji Enoki
Keyword(s):  
Heat Flux ◽  
Heat Removal ◽  
High Heat ◽  
High Heat Flux ◽  
Micro Channel

Thermo-Fluid-Stress-Deformation Analysis of Two-Layer Microchannels for Cooling Chips With Hot Spots

2015 ◽  
Vol 137 (3) ◽  
Author(s):  
Abas Abdoli ◽  
George S. Dulikravich ◽  
Genesis Vasquez ◽  
Siavash Rastkar
Keyword(s):  
Heat Flux ◽  
Thermal Stresses ◽  
Hot Spot ◽  
Heat Removal ◽  
High Heat ◽  
Heat Transfer Analysis ◽  
Deformation Analysis ◽  
High Heat Flux ◽  
Cooling Design ◽  
Microchannel Cooling

Two-layer single phase flow microchannels were studied for cooling of electronic chips with a hot spot. A chip with 2.45 × 2.45 mm footprint and a hot spot of 0.5 × 0.5 mm in its center was studied in this research. Two different cases were simulated in which heat fluxes of 1500 W cm−2 and 2000 W cm−2 were applied at the hot spot. Heat flux of 1000 W cm−2 was applied on the rest of the chip. Each microchannel layer had 20 channels with an aspect ratio of 4:1. Direction of the second microchannel layer was rotated 90 deg with respect to the first layer. Fully three-dimensional (3D) conjugate heat transfer analysis was performed to study the heat removal capacity of the proposed two-layer microchannel cooling design for high heat flux chips. In the next step, a linear stress analysis was performed to investigate the effects of thermal stresses applied to the microchannel cooling design due to variations of temperature field. Results showed that two-layer microchannel configuration was capable of removing heat from high heat flux chips with a hot spot.

Dependence of Heat Transfer Coefficient on Porous Structure in Porous Media

2008 ◽  
Author(s):  
Akira Matsui ◽  
Kazuhisa Yuki ◽  
Hidetoshi Hashizume
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Porous Media ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
High Performance ◽  
Heat Removal ◽  
High Heat ◽  
Metal Foams ◽  
High Heat Flux

Detailed heat transfer characteristics of particle-sintered porous media and metal foams are evaluated to specify the important structural parameters suitable for high heat removal. The porous media used in this experiment are particle-sintered porous media made of bronze and SUS316L, and metal foams made of copper and nickel. Cooling water flows into the porous medium opposite to heat flux input loaded by a plasma arcjet. The result indicates that the bronze-particle porous medium of 100μm in pore size shows the highest performance and achieves heat transfer coefficient of 0.035MW/m2K at inlet heat flux 4.6MW/m2. Compared with the heat transfer performance of copper fiber-sintered porous media, the bronze particlesintered ones give lower heat transfer coefficient. However, the stable cooling conditions that the heat transfer coefficient does not depend on the flow velocity, were confirmed even at heat flux of 4.6MW/m2 in case of the bronze particle-sintered media, while not in the case of the copper-fiber sintered media. This signifies the possibility that the bronze-particle sintered media enable much higher heat flux removal of over 10MW/m2, which could be caused by higher permeability of the particle-sintered pore structures. Porous media with high permeability provide high performance of vapor evacuation, which leads to more stable heat removal even under extremely high heat flux. On the other hand, the heat transfer coefficient of the metal foams becomes lower because of the lower capillary and fin effects caused by too high porosity and low effective thermal conductivity. It is concluded that the pore structure having high performance of vapor evacuation as well as the high capillary and high fin effects is appropriate for extremely high heat flux removal of over 10MW/m2.

A Numerical Model of a Reciprocating-Mechanism Driven Heat Loop for Two-Phase High Heat Flux Cooling

2016 ◽  
Vol 8 (4) ◽  
Author(s):  
Olubunmi Popoola ◽  
Ayobami Bamgbade ◽  
Yiding Cao
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Numerical Model ◽  
Performance Optimization ◽  
Numerical Study ◽  
High Heat ◽  
Working Fluid ◽  
High Heat Flux ◽  
Two Phase ◽  
Transfer Device

An effective design option for a cooling system is to use a two-phase pumped cooling loop to simultaneously satisfy the temperature uniformity and high heat flux requirements. A reciprocating-mechanism driven heat loop (RMDHL) is a novel heat transfer device that could attain a high heat transfer rate through a reciprocating flow of the two-phase working fluid inside the heat transfer device. Although the device has been tested and validated experimentally, analytical or numerical study has not been undertaken to understand its working mechanism and provide guidance for the device design. The objective of this paper is to develop a numerical model for the RMDHL to predict its operational performance under different working conditions. The developed numerical model has been successfully validated by the existing experimental data and will provide a powerful tool for the design and performance optimization of future RMDHLs. The study also reveals that the maximum velocity in the flow occurs near the wall rather than at the center of the pipe, as in the case of unidirectional steady flow. This higher velocity near the wall may help to explain the enhanced heat transfer of an RMDHL.

Flow Boiling Enhancement in Microchannels With Diffusion Bonded Wire Mesh

2007 ◽  
Author(s):  
Hailei Wang ◽  
Richard Peterson
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Boiling ◽  
Nucleate Boiling ◽  
High Heat ◽  
Wire Mesh ◽  
Working Fluid ◽  
High Heat Flux ◽  
Vapor Quality ◽  
Heating Wall

Flow boiling and heat transfer enhancement in four parallel microchannels using a dielectric working fluid, HFE 7000, was investigated. Each channel was 1000 μm wide and 510 μm high. A unique channel surface enhancement technique via diffusion bonding a layer of conductive fine wire mesh onto the heating wall was developed. According to the obtained flow boiling curves for both the bare and mesh channels, the amount of wall superheat was significantly reduced for the mesh channel at all stream-wise locations. This indicated that the nucleate boiling in the mesh channel was enhanced due to the increase of nucleation sites the mesh introduced. Both the nucleate boiling dominated and convective evaporation dominated regimes were identified. In addition, the overall trend for the flow boiling heat transfer coefficient, with respect to vapor quality, was increasing until the vapor quality reached approximately 0.4. The critical heat flux (CHF) for the mesh channel was also significantly higher than that of the bare channel in the low vapor quality region. Due to the fact of how the mesh was incorporated into the channels, no pressure drop penalty was identified for the mesh channels. Potential applications for this kind of mesh channel include high heat-flux electronic cooling systems and various energy conversion systems.

Nucleate Boiling of Dielectric Liquids on Hydrophobic Patterned Surfaces

2014 ◽  
Author(s):  
Nihal E. Joshua ◽  
Denesh K. Ajakumar ◽  
Huseyin Bostanci
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Nucleate Boiling ◽  
High Heat ◽  
Copper Surface ◽  
Dielectric Liquid ◽  
Working Fluid ◽  
Patterned Surfaces ◽  
High Heat Flux ◽  
Dielectric Liquids

This study experimentally investigated the effect of hydrophobic patterned surfaces in nucleate boiling heat transfer. A dielectric liquid, HFE-7100, was used as the working fluid in the saturated boiling tests. Dielectric liquids are known to have highly-wetting characteristics. They tend to fill surface cavities that would normally trap vapor/gas, and serve as active nucleation sites during boiling. With the lack of these vapor filled cavities, boiling of a dielectric liquid leads to high incipience superheats and accompanying temperature overshoots. Heater samples in this study were prepared by applying a thin Teflon (AF400, Dupont) coating on 1-cm2 smooth copper surfaces following common photolithography techniques. Matching size thick film resistors, attached onto the copper samples, generated heat and simulated high heat flux electronic devices. Tests investigated the heater samples featuring circular pattern sizes between 40–100 μm, and corresponding pitch sizes between 80–200 μm. Additionally, a plain, smooth copper surface was tested to obtain reference data. Based on data, hydrophobic patterned surfaces effectively eliminated the temperature overshoot at boiling incipience, and considerably improved nucleate boiling performance in terms of heat transfer coefficient and critical heat flux over the reference surface. Hydrophobic patterned surfaces therefore demonstrated a practical surface modification method for heat transfer enhancement in immersion cooling applications.

scholarly journals Thermal Assessment of Nano-Particulate Graphene-Water/Ethylene Glycol (WEG 60:40) Nano-Suspension in a Compact Heat Exchanger

Energies ◽  
2019 ◽  
Vol 12 (10) ◽  
pp. 1929 ◽  
Author(s):  
M. Sarafraz ◽  
Mohammad Safaei ◽  
Zhe Tian ◽  
Marjan Goodarzi ◽  
Enio Bandarra Filho ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Ethylene Glycol ◽  
Thermal Performance ◽  
Evaluation Criteria ◽  
High Heat ◽  
Operating Conditions ◽  
Working Fluid ◽  
High Heat Flux ◽  
Micro Channel

In the present study, we report the results of the experiments conducted on the convective heat transfer of graphene nano-platelets dispersed in water-ethylene glycol. The graphene nano-suspension was employed as a coolant inside a micro-channel and heat-transfer coefficient (HTC) and pressure drop (PD) values of the system were reported at different operating conditions. The results demonstrated that the use of graphene nano-platelets can potentially augment the thermal conductivity of the working fluid by 32.1% (at wt. % = 0.3 at 60 °C). Likewise, GNP nano-suspension promoted the Brownian motion and thermophoresis effect, such that for the tests conducted within the mass fractions of 0.1%–0.3%, the HTC of the system was improved. However, a trade-off was identified between the PD value and the HTC. By assessing the thermal performance evaluation criteria (TPEC) of the system, it was identified that the thermal performance of the system increased by 21% despite a 12.1% augmentation in the PD value. Furthermore, with an increment in the fluid flow and heat-flux applied to the micro-channel, the HTC was augmented, showing the potential of the nano-suspension to be utilized in high heat-flux thermal applications.

10310 A study on high heat flux heat removal with phase change using a porous metal

2014 ◽  
Vol 2014.20 (0) ◽  
pp. _10310-1_-_10310-2_
Author(s):  
Daiki Hanzawa ◽  
Kyosuke Katsumata ◽  
Tomio Okawa
Keyword(s):  
Heat Flux ◽  
Phase Change ◽  
Heat Removal ◽  
Porous Metal ◽  
High Heat ◽  
High Heat Flux

A Study on High Heat Flux Heat Removal With Boiling Using Porous Microchannel

2014 ◽  
Author(s):  
Daiki Hanzawa ◽  
Kyosuke Katsumata ◽  
Tomio Okawa
Keyword(s):  
Heat Flux ◽  
Pore Size ◽  
Mass Flux ◽  
Pressure Loss ◽  
Heat Removal ◽  
Porous Metal ◽  
High Heat ◽  
High Mass ◽  
High Heat Flux ◽  
Small Flow

This paper reports the critical heat flux (CHF) enhancement that was observed experimentally when a porous metal was placed in a small flow channel (hereafter, this channel is called a “porous microchannel”). In the porous microchannel, the CHF value increased almost linearly with increased values of the mass flux and the inlet subcooling. In consequence, higher cooling performance was achieved under high mass flux and high inlet subcooling conditions. It was also found that considerable fluctuation of the pressure loss frequently encountered in a small heated channel disappears in the porous microchannel. It was considered that the stabilization of the pressure loss can mainly be attributed to inhibition of the formation of large bubbles. The effects of the material and the pore size of the porous metal were also investigated. Silver and nickel were selected as the porous metal material and the pore size tested was 0.2 and 0.6 mm. In the present experiments, the CHF value was not influenced significantly by the material in spite of the distinct difference of the thermal conductivity between silver and nickel, whilst it was dependent noticeably on the pore size. It was hence suggested that the CHF enhancement observed in this work was mainly caused by the complex thermal-hydraulic field formed in the porous microchannel. Preliminary results of the flow visualization performed to reveal the mechanisms of the CHF enhancement in the porous microchannel was also reported.

Sign in / Sign up

Export Citation Format

Share Document