Simulating Fine Particle Deposition in Coolant Channel of Fast Reactor

2017 ◽  
Author(s):  
Yaoxin Wang ◽  
Tao Zhou ◽  
Bing Li
Keyword(s):  
Fuel Assembly ◽  
Fast Reactor ◽  
Particle Deposition ◽  
Fluid Phase ◽  
Fixed Time ◽  
Mitigation Measures ◽  
Fuel Cladding ◽  
Discrete Phase Model ◽  
Discrete Phase ◽  
Fluent Software

When fast reactor is operation, because of scouring by high pressure liquid coolant in fuel assembly, there are a lot of products in coolant channel. Using FLUENT software simulate deposition of insoluble particle in fast reactor. Using standard k-ε model predict flow field and turbulence intensity of fluid phase. Using discrete phase model track the trajectory of insoluble particle. The following are simulation results. Fuel cladding deposits lots of insoluble particle, but the concentration of insoluble particle is lower at the central of coolant; Entrance section of the insoluble particle concentration is higher than exit section; Dot deposition of insoluble particle at outlet of fuel cladding will lead to pitting phenomenon, pitting will cause deterioration of heat transfer and destroy the integrity of cladding. In view of deposition law of insoluble particle and characteristic of fuel assembly, mitigation measures of cleaning insoluble particle at fixed time and fixed position are being proposed.

A Simulation of the Number of Particles Trapped by the Circulating Filter of a Hard Disk Drive and their Trajectories

2014 ◽  
Vol 548-549 ◽  
pp. 953-957 ◽  
Author(s):  
Jatuporn Thongsri ◽  
Vana Pongkom
Keyword(s):  
Shear Stress ◽  
Hard Disk Drive ◽  
Hard Disk ◽  
Disk Drive ◽  
Optimal Placement ◽  
Discrete Phase Model ◽  
Discrete Phase ◽  
Fluent Software ◽  
The Right ◽  
Number Of Particles

A transition shear stress transport turbulence model and a discrete phase model of Fluent software were employed to simulate numerically the trajectories of loose particles and the number of them trapped by the circulating filter of a hard disk drive (HDD). The filter was located either at the left or the right of a 2.5 inch dual platter HDD rotating at 7200 rpm. Particles were released from the middle diameter position where four head gimbal assemblies (HGAs) were located. The simulation included airflow and particle trajectories released from any of the four HGAs. The results of this simulation can help determine the efficiency of a circulating filter and its optimal placement.

Unsteady Modeling of Powdered Activated Carbon Deposition on Collection Electrode of a Lab-Scale Electrostatic Precipitator (ESP)

2012 ◽  
Author(s):  
Yasmin Khakpour ◽  
Herek L. Clack
Keyword(s):  
Activated Carbon ◽  
Particle Deposition ◽  
Electrostatic Precipitator ◽  
Activated Carbons ◽  
Collection Efficiency ◽  
Continuous Phase ◽  
Powdered Activated Carbon ◽  
Computational Domain ◽  
Discrete Phase Model ◽  
Discrete Phase

Particulate sampling in the flue gas at the Electrostatic Precipitator (ESP) outlet during injection of powdered activated carbons (PACs) has provided strong anecdotal evidence indicating that injected PACs can penetrate the ESP in significant concentrations. The low resistivity of PAC is consistent with poor collection efficiency in an ESP and lab-scale testing has revealed significantly different collection behavior of PAC in an ESP as compared to fly ash. The present study illustrates the use of a commercial CFD package — FLUENT — to investigate precipitation of powdered activated carbon (PAC) in the presence and absence of electric field. The computational domain is designed to represent a 2-D wire-plate ESP channel. The governing equations include those covering continuous phase transport, electric potential, air ionization, and particle charging. The particles are tracked using a Lagrangian Discrete Phase Model (DPM). In addition, a custom user-defined function (UDF) uses a deforming boundary condition and a prescribed critical particle velocity to account for particle deposition and dust-cake growth on the electrodes. The effect of Electrohydrodynamics (EHD) induced flow on the ESP collection efficiency under various flow and particle characteristics as well as different ESP configurations are illustrated.

A Numerical Study of Particle Deposition Through Fuel Pebble Bed in HTGR

2018 ◽  
Author(s):  
Qi Sun ◽  
Gang Zhao ◽  
Wei Peng ◽  
Suyuan Yu
Keyword(s):  
Particle Deposition ◽  
Numerical Study ◽  
Three Dimensional ◽  
Intensity Change ◽  
Discrete Phase Model ◽  
Pebble Bed ◽  
Deposition Fraction ◽  
Discrete Phase ◽  
Face Centered ◽  
Fuel Elements

The study on the deposition of graphite dust is significant to the safety of High-Temperature Gas-cooled Reactor (HTGR) due to potential accident such as localized hot-spots and intensity change which is caused by the graphite dust generated by abrasion of fuel elements. Based on the steady flow and three-dimensional face centered structures of fuel pebble bed, the discrete phase model (DPM) were applied to simulate trajectory of graphite dust in conditions of HTGR. To determinate the deposition of particle, the present study introduces a rebound condition with critical velocity by a user defined function. The particle trajectories show most of particle deposition can be summed up as the effect of backflow region, turbulent diffusion and inertial impact. The original trap condition overestimates the deposition fraction especially for large particles compared with involving rebound condition. In addition, the trend of deposition fraction shows as the dimeter of particle increases, deposition fraction decreases first and then increases.

scholarly journals STUDY OF CALCITE PRECIPITATION IN WELL CONDITIONS USING THE DDPM-DPM APPROACH

2021 ◽  
Vol 51 (2) ◽  
pp. 101-106
Author(s):  
Suellen Freire Rigatto da Cruz ◽  
Fabio De Assis Ressel Pereira ◽  
Daniel Da Cunha Ribeiro ◽  
André Leibsohn Martins ◽  
Oldrich Joel Romero
Keyword(s):  
Particle Deposition ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Computational Effort ◽  
Scale Formation ◽  
Discrete Phase Model ◽  
Calcite Precipitation ◽  
Discrete Phase ◽  
It Application ◽  
Calcium Carbonate Scale

The extraction of oil results in problems such as the scale formation in the various stages of the production process. The scale reduces all or part of the flow conduits, increasing the pressure drop and reducing oil production. In this work the three dimensional, transient, turbulent, biphasic problem is solved by combining the Dense Discrete Phase Model (DDPM) and Discrete Element Method (DEM), to analyze the influence of certain parameters on the particle deposition, which represents the calcium carbonate scale formation, inside the wall of a horizontal pipeline at well conditions. The obtained results show that particle deposition is higher at lower Reynolds numbers. The results also show that the use of DEM model is more representative, but due to the high computational effort required, it application in complex geometries must be carefully evaluated.

scholarly journals Effects of Blade Parameters on the Flow Field and Classification Performance of the Vertical Roller Mill via Numerical Investigations

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Chang Liu ◽  
Zuobing Chen ◽  
Weili Zhang ◽  
Chenggang Yang ◽  
Ya Mao ◽  
...  
Keyword(s):  
Flow Field ◽  
Pressure Difference ◽  
Continuous Phase ◽  
Classification Performance ◽  
Field Analysis ◽  
Discrete Phase Model ◽  
Roller Mill ◽  
Discrete Phase ◽  
Vertical Roller ◽  
Classification Efficiency

The vertical roller mill is an important crushing and grading screening device widely used in many industries. Its classification efficiency and the pressure difference determine the entire producing capacity and power consumption, respectively, which makes them the two key indicators describing the mill performance. Based on the DPM (Discrete Phase Model) and continuous phase coupling model, the flow field characteristics in the vertical roller mill including the velocity and pressure fields and the discrete phase distributions had been analyzed. The influence of blade parameters like the shape, number, and rotating speed on the flow field and classification performance had also been comprehensively explored. The numerical simulations showed that there are vortices in many zones in the mill and the blades are of great significance to the mill performance. The blade IV not only results in high classification efficiency but also reduces effectively the pressure difference in the separator and also the whole machine. The conclusions of the flow field analysis and the blade effects on the classification efficiency and the pressure difference could guide designing and optimizing the equipment structure and the milling process, which is of great importance to obtain better overall performance of the vertical roller mill.

scholarly journals Enhanced discrete phase model for multiphase flow simulation of blood flow with high shear stress

2021 ◽  
Vol 104 (1) ◽  
pp. 003685042110080
Author(s):  
Zheqin Yu ◽  
Jianping Tan ◽  
Shuai Wang
Keyword(s):  
Blood Flow ◽  
Shear Stress ◽  
Multiphase Flow ◽  
Experimental Verification ◽  
Flow Simulation ◽  
Turbulence Models ◽  
Phase Model ◽  
Force Model ◽  
Discrete Phase Model ◽  
Discrete Phase

Shear stress is often present in the blood flow within blood-contacting devices, which is the leading cause of hemolysis. However, the simulation method for blood flow with shear stress is still not perfect, especially the multiphase flow model and experimental verification. In this regard, this study proposes an enhanced discrete phase model for multiphase flow simulation of blood flow with shear stress. This simulation is based on the discrete phase model (DPM). According to the multiphase flow characteristics of blood, a virtual mass force model and a pressure gradient influence model are added to the calculation of cell particle motion. In the experimental verification, nozzle models were designed to simulate the flow with shear stress, varying the degree of shear stress through different nozzle sizes. The microscopic flow was measured by the Particle Image Velocimetry (PIV) experimental method. The comparison of the turbulence models and the verification of the simulation accuracy were carried out based on the experimental results. The result demonstrates that the simulation effect of the SST k- ω model is better than other standard turbulence models. Accuracy analysis proves that the simulation results are accurate and can capture the movement of cell-level particles in the flow with shear stress. The results of the research are conducive to obtaining accurate and comprehensive analysis results in the equipment development phase.

scholarly journals Comparative Study on Fuel Assembly of Modular Gas-cooled Fast Reactor using MCNP and OpenMC Code

2021 ◽  
Vol 1772 (1) ◽  
pp. 012031
Author(s):  
H. Raflis ◽  
M. Ilham ◽  
Z. Su’ud ◽  
A. Waris ◽  
D. Irwanto
Keyword(s):  
Comparative Study ◽  
Fuel Assembly ◽  
Fast Reactor

Effect of position of the fiber transport channel on fiber motion in the high-speed rotor

2021 ◽  
pp. 004051752110018
Author(s):  
Rui Hua Yang ◽  
Chuang He ◽  
Bo Pan ◽  
Hongxiu Zhong ◽  
Cundong Xu
Keyword(s):  
High Speed ◽  
Channel Model ◽  
Three Dimensional ◽  
Discrete Phase Model ◽  
Transport Channel ◽  
Rotor Spinning ◽  
Fiber Motion ◽  
Discrete Phase ◽  
Airflow Field ◽  
Fiber Transport

The task of the fiber transport channel (FTC) is to transport the fibers from the carding roller to the rotor. Its geometric position in the spinning machine has a strong influence on the characteristics of the airflow field and the trajectory of the fiber motion in both the rotor and the FTC. In this paper, a three-dimensional pumping rotor spinning channel model was established using ANSYS-ICEM-CFD software with three different positions of the FTC (positions a–c). Further, the simulations of air distribution were performed using Fluent software. In addition, the discrete phase model was used to fit the fiber motion trajectory in the rotor. The simulation results showed that among the three types of FTC, position b is the optimal condition. The gradients of airflow velocity in the channel at position b were greater than those of the other two positions, which is conducive to straightening of the fiber.

Sign in / Sign up

Export Citation Format

Share Document