Surface Roughness Effects on Circular Cylinders at High Reynolds Numbers

2002 ◽  
Author(s):  
M. Eaddy ◽  
W. H. Melbourne ◽  
J. Sheridan
Keyword(s):  
Surface Roughness ◽  
Reynolds Numbers ◽  
Circular Cylinders ◽  
Flow Induced Vibration ◽  
Roughness Effects ◽  
Vortex Induced Vibration ◽  
Smooth Cylinder ◽  
Lift Forces ◽  
High Reynolds ◽  
Effect Of Surface

The problem of flow-induced vibration has been studied extensively. However, much of this research has focused on the smooth cylinder to gain an understanding of the mechanisms that cause vortex-induced vibration. In this paper results of an investigation of the effect of surface roughness on the cross-wind forces are presented. Measurements of the sectional RMS fluctuating lift forces and the axial correlation of the pressures for Reynolds numbers from 1 × 105 to 1.4 × 106 are given. It was found that surface roughness significantly increased the axial correlation of the pressures to similar values found at high subcritical Reynolds numbers. There was little effect of the surface roughness on the sectional lift forces. The improved correlation of the vortex shedding means rough cylinders will be subject to larger cross-wind forces and an increased possibility of vortex-induced vibration compared to smooth cylinders.

Velocity Distribution in Turbulent Flow

1970 ◽  
Vol 12 (6) ◽  
pp. 391-399 ◽  
Author(s):  
W. K. Allan
Keyword(s):  
Surface Roughness ◽  
Turbulent Flow ◽  
Velocity Distribution ◽  
Flat Plate ◽  
Reynolds Numbers ◽  
Pressure Gradients ◽  
Roughness Effects ◽  
High Reynolds ◽  
Independent Effects ◽  
Good Agreement

A general equation for the velocity distribution in steady, incompressible, two-dimensional, turbulent flow is constructed by correction of the logarithmic velocity profile for the independent effects of pressure gradients and of surface roughness. Predicted characteristics of pipe flows, flat plate flows, and diffusing flows over smooth surfaces are found to be in good agreement with empirical data at high Reynolds numbers. Pipe flow data are used to evaluate surface roughness effects, and hence to describe flat plate flows and diffusing flows over rough surfaces.

Vortex Induced Vibration Tests of Smooth and Rough Flexible Cylinders at High Reynolds Numbers

2005 ◽  
Author(s):  
Don W. Allen ◽  
Dean L. Henning ◽  
Li Lee
Keyword(s):  
Surface Roughness ◽  
High Speed ◽  
Single Mode ◽  
Reynolds Numbers ◽  
Circular Path ◽  
Exterior Surface ◽  
Vortex Induced Vibration ◽  
High Reynolds Numbers ◽  
Sheared Flows ◽  
High Reynolds

Vortex-induced vibration (VIV) tests have been performed on long, flexible pipes with various levels of roughness, in sheared flows in a circular towing tank at high Reynolds numbers. The test pipes, made of fiberglass composite, were mounted horizontally beneath a rotating arm that has a span of 129 ft, and a width of 25 ft. As the towing bridge rotates, it drives the cylinder in a circular path in still water. The sheared flows experienced by the cylinder excite its VIV motion. The Reynolds numbers for the tests reported herein ranged from 152,000 to 339,000 at the high-speed end of the pipe. Two surface roughness levels were tested: one comprised of the exterior surface of a filament wound fiberglass pipe; and one with carpet glued to the exterior of the pipe. The VIV responses of the test cylinders, represented by displacement time traces, spectrum, and motion trajectories, are presented in this paper. Effects of the surface roughness and Reynolds numbers on the VIV responses are discussed. The response behavior of the cylinders varied from single-mode dominance to multi-mode responses, in addition to certain traveling wave activities. These results should be of interest to researchers and engineers in the area of vortex-induced vibrations.

In-Line and Transverse Forces on Cylinders in Oscillatory Flow at High Reynolds Numbers

1977 ◽  
Vol 21 (04) ◽  
pp. 200-216 ◽  
Author(s):  
Turgut Sarpkaya
Keyword(s):  
Oscillatory Flow ◽  
Least Squares Method ◽  
Reynolds Numbers ◽  
Transverse Force ◽  
Circular Cylinders ◽  
Relative Roughness ◽  
High Reynolds Numbers ◽  
Smooth Cylinder ◽  
New Interpretation ◽  
High Reynolds

This paper presents the results of an extensive experimental investigation of the in-line and transverse forces acting on smooth and sand roughened circular cylinders placed in oscillatory flow at Reynolds numbers up to 1.5 × 106, Keulegan Carpenter numbers up to 100, and relative roughnesses from 1/800 to 1/50. The drag and inertia coefficients have been determined through the use of the Fourier analysis and the least-squares method. The transverse force (lift) has been analyzed in terms of its maximum, semi peak-to-peak, and root-mean-squarevalues. In addition, the frequency of vortex shedding and the Strouhal number have been determined. The results have shown that (a) for smooth cylinders, all of the coefficients just cited are functions of the Reynolds and Keulegan-Carpenter numbers, particularly for Reynolds numbers larger than about 20 000; (b) for rough cylinders, the force coefficients also depend on the relative roughness k/D and differ significantly from corresponding to the smooth cylinder; and that (c) the use of the frequencyparameter' D2/vT and the roughness Reynolds number Umk/vallows a new interpretation of the present as well as the previously obtained data.

scholarly journals Aerodynamics of smooth and rough square-section prisms at incidence in very high Reynolds-number cross-flows

2021 ◽  
Vol 62 (3) ◽  
Author(s):  
Nils Paul van Hinsberg
Keyword(s):  
Reynolds Number ◽  
Cross Sections ◽  
Reynolds Numbers ◽  
Circular Cylinders ◽  
Surface Boundary ◽  
Experimental Proof ◽  
Surface Boundary Layer ◽  
Pitch Moment ◽  
The Mean ◽  
High Reynolds

Abstract The aerodynamics of smooth and slightly rough prisms with square cross-sections and sharp edges is investigated through wind tunnel experiments. Mean and fluctuating forces, the mean pitch moment, Strouhal numbers, the mean surface pressures and the mean wake profiles in the mid-span cross-section of the prism are recorded simultaneously for Reynolds numbers between 1$$\times$$ × 10$$^{5}$$ 5 $$\le$$ ≤ Re$$_{D}$$ D $$\le$$ ≤ 1$$\times$$ × 10$$^{7}$$ 7 . For the smooth prism with $$k_s$$ k s /D = 4$$\times$$ × 10$$^{-5}$$ - 5 , tests were performed at three angles of incidence, i.e. $$\alpha$$ α = 0$$^{\circ }$$ ∘ , −22.5$$^{\circ }$$ ∘ and −45$$^{\circ }$$ ∘ , whereas only both “symmetric” angles were studied for its slightly rough counterpart with $$k_s$$ k s /D = 1$$\times$$ × 10$$^{-3}$$ - 3 . First-time experimental proof is given that, within the accuracy of the data, no significant variation with Reynolds number occurs for all mean and fluctuating aerodynamic coefficients of smooth square prisms up to Reynolds numbers as high as $$\mathcal {O}$$ O (10$$^{7}$$ 7 ). This Reynolds-number independent behaviour applies to the Strouhal number and the wake profile as well. In contrast to what is known from square prisms with rounded edges and circular cylinders, an increase in surface roughness height by a factor 25 on the current sharp-edged square prism does not lead to any notable effects on the surface boundary layer and thus on the prism’s aerodynamics. For both prisms, distinct changes in the aerostatics between the various angles of incidence are seen to take place though. Graphic abstract

A Model for High-Reynolds-Number Flow Past Rough-Walled Circular Cylinders

1977 ◽  
Vol 99 (3) ◽  
pp. 486-493 ◽  
Author(s):  
O. Gu¨ven ◽  
V. C. Patel ◽  
C. Farell
Keyword(s):  
Boundary Layer ◽  
Surface Roughness ◽  
Circular Cylinder ◽  
Turbulent Boundary Layer ◽  
Pressure Coefficient ◽  
Empirical Relation ◽  
Reynolds Numbers ◽  
Boundary Layer Separation ◽  
Circular Cylinders ◽  
Mean Flow

A simple analytical model for two-dimensional mean flow at very large Reynolds numbers around a circular cylinder with distributed roughness is presented and the results of the theory are compared with experiment. The theory uses the wake-source potential-flow model of Parkinson and Jandali together with an extension to the case of rough-walled circular cylinders of the Stratford-Townsend theory for turbulent boundary-layer separation. In addition, a semi-empirical relation between the base-pressure coefficient and the location of separation is used. Calculation of the boundary-layer development, needed as part of the theory, is accomplished using an integral method, taking into account the influence of surface roughness on the laminar boundary layer and transition as well as on the turbulent boundary layer. Good agreement with experiment is shown by the results of the theory. The significant effects of surface roughness on the mean-pressure distribution on a circular cylinder at large Reynolds numbers and the physical mechanisms giving rise to these effects are demonstrated by the model.

Effect of Surface Roughness on Gaseous Flow Through Microchannels

2000 ◽  
Author(s):  
Stephen E. Turner ◽  
Hongwei Sun ◽  
Mohammad Faghri ◽  
Otto J. Gregory
Keyword(s):  
Surface Roughness ◽  
Reynolds Number ◽  
Friction Factor ◽  
Reynolds Numbers ◽  
Helium Flow ◽  
Local Pressure ◽  
Aspect Ratios ◽  
Corrugated Surfaces ◽  
Flow Through ◽  
Effect Of Surface

Abstract This paper presents an experimental investigation on nitrogen and helium flow through microchannels etched in silicon with hydraulic diameters between 10 and 40 microns, and Reynolds numbers ranging from 0.3 to 600. The objectives of this research are (1) to fabricate microchannels with uniform surface roughness and local pressure measurement; (2) to determine the friction factor within the locally fully developed region of the microchannel; and (3) to evaluate the effect of surface roughness on momentum transfer by comparison with smooth microchannels. The friction factor results are presented as the product of friction factor and Reynolds number plotted against Reynolds number. The following conclusions have been reached in the present investigation: (1) microchannels with uniform corrugated surfaces can be fabricated using standard photolithographic processes; and (2) surface features with low aspect ratios of height to width have little effect on the friction factor for laminar flow in microchannels.

Sign in / Sign up

Export Citation Format

Share Document