Numerical Analysis on Nanofluid Forced Convection in Ducts With Triangular Cross Sections

2011 ◽  
Author(s):  
O. Manca ◽  
S. Nardini ◽  
D. Ricci ◽  
S. Tamburrino
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Forced Convection ◽  
Cross Sections ◽  
Fluid Dynamic ◽  
Pure Water ◽  
Convection Flow ◽  
Uniform Heat Flux ◽  
Surface Shear Stress ◽  
Surface Shear

Heat transfer of fluids is very important to many industrial heating or cooling equipments. Convective heat transfer can be enhanced passively by changing flow geometry, boundary conditions or by enhancing the thermal conductivity of the working fluids. An innovative way of improving the fluid thermal conductivity is to introduce suspended small solid nanoparticles in the base fluids. In this paper a numerical investigation on laminar forced convection flow of a water–Al2O3 nanofluid in a duct having an equilateral triangular cross section is performed. The hydraulic diameter is set equal to 1.0×10−2 m. A constant and uniform heat flux on the external surfaces has been applied and the single-phase model approach has been employed. The analysis has been run in steady state regime for a nanoparticle size equal to 38 nm, considering different volume particle concentrations. The CFD code Fluent has been employed in order to solve the tri-dimensional numerical model. Results are presented in terms of temperature and velocity distributions, surface shear stress and heat transfer convective coefficient, Nusselt number and required pumping power profiles. Comparison with results related to the fluid dynamic and thermal behaviors in pure water are carried out in order to evaluate the enhancement due to the presence of nanoparticles in terms of volumetric concentration.

scholarly journals On a Homotopy Perturbation Treatment of Steady Laminar Forced Convection Flow over a Nonlinearly Stretching Porous Sheet

2014 ◽  
Vol 2014 ◽  
pp. 1-8
Author(s):  
Nemat Dalir ◽  
Salman Nourazar
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Forced Convection ◽  
Convection Flow ◽  
Surface Shear Stress ◽  
Surface Shear ◽  
Suction Parameter ◽  
Sheet Surface ◽  
Homotopy Perturbation ◽  
Laminar Forced Convection

The steady two-dimensional laminar forced convection boundary layer flow of an incompressible viscous Newtonian fluid over a nonlinearly stretching porous (permeable) sheet with suction is considered. The sheet’s permeability is also considered to be nonlinear. The boundary layer equations are transformed by similarity transformations to a nonlinear ordinary differential equation (ODE). Then the homotopy perturbation method (HPM) is used to solve the resultant nonlinear ODE. The dimensionless entrainment parameter and the dimensionless sheet surface shear stress are obtained for various values of the suction parameter and the nonlinearity factor of sheet stretching and permeability. The results indicate that the dimensionless sheet surface shear stress decreases with the increase of suction parameter. The results of present HPM solution are compared to the values obtained in a previous study by the homotopy analysis method (HAM). The HPM results show that they are in good agreement with the HAM results within 2% error.

scholarly journals Conjugate effects of temperature sensitive viscosity and thermal conductivity on free convection flow along a wavy surface with heat generation

2013 ◽  
Vol 10 (2) ◽  
pp. 139-148 ◽  
Author(s):  
Md. Abdul Alim ◽  
M. Miraj Akand ◽  
M. Rezaul Karim
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Heat Generation ◽  
Skin Friction Coefficient ◽  
Numerical Results ◽  
Wavy Surface ◽  
Convection Flow ◽  
Surface Shear Stress

The effects of internal heat generation on natural convection flow with temperature dependent variable viscosity along a uniformly heated vertical wavy surface have been investigated. The governing boundary layer equations are first transformed into a non-dimensional form using suitable set of dimensionless variables. The resulting nonlinear system of partial differential equations are mapped into the domain of a vertical flat plate and then solved numerically employing the implicit finite difference method, known as Keller-box scheme. Numerical results of the surface shear stress in terms of skin friction coefficient and the rate of heat transfer in terms of local Nusselt number, the stream lines as well as the isotherms are shown graphically for a selection of parameters set consisting of viscosity variation parameter e, thermal conductivity parameter g, heat generation parameter Q and Prandtl number Pr. Numerical results of the local skin friction coefficient and the rate of heat transfer for different values are presented in tabular form and graphically.DOI: http://dx.doi.org/10.3329/jname.v10i2.9450

Simulation of three-dimensional laminar forced convection flow of a radiating gas over an inclined backward-facing step in a duct under bleeding condition

2012 ◽  
Vol 227 (2) ◽  
pp. 332-345 ◽  
Author(s):  
M Atashafrooz ◽  
SA Gandjalikhan Nassab
Keyword(s):  
Heat Transfer ◽  
Forced Convection ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Numerical Procedure ◽  
Discrete Ordinates ◽  
Convection Flow ◽  
Backward Facing Step ◽  
Forced Convection Flow ◽  
Laminar Forced Convection

This study presents a numerical analysis of three-dimensional laminar forced convection flow of a radiating gas over an inclined backward-facing step in a rectangular duct under bleeding condition. The fluid is treated as a gray, absorbing, emitting, and scattering medium. The three-dimensional Cartesian coordinate system is used to solve the governing equations which are the conservations of mass, momentum, and energy. These equations are solved numerically using the computational fluid dynamic techniques to obtain the temperature and velocity fields, while the blocked-off method is employed to simulate the incline surface. Discretized forms of these equations are obtained by the finite volume method and solved using the SIMPLE algorithm. Since the gas is considered as a radiating medium, besides the convective and conductive terms in the energy equation, the radiative term also presented. For computation of this term, the radiative transfer equation is solved numerically by the discrete ordinates method to find the divergence of radiative heat flux distribution inside the radiating medium. By this numerical procedure, the role of radiation heat transfer on convection flow of a radiating gas which has many engineering applications (for example in heat exchangers and combustion chambers) is studied in detail. Beside, the effects of bleeding coefficient, albedo coefficient, optical thickness, and the radiation–conduction parameter on heat transfer behavior of the system are investigated. Comparison of numerical results with the available data published in the open literature shows a good agreement.

Numerical Investigation of Forced Convection of Nanofluids in Circular Tubes

2007 ◽  
Author(s):  
Fabio Chiacchio ◽  
Oronzio Manca ◽  
Sergio Nardini
Keyword(s):  
Heat Transfer ◽  
Forced Convection ◽  
Convective Heat Transfer Coefficient ◽  
Convection Flow ◽  
Uniform Heat Flux ◽  
Particle Volume ◽  
Two Phase ◽  
Liquid Heat ◽  
Temperature Dependent Properties ◽  
Laminar Forced Convection

In this paper developing laminar forced convection flow of a water–γAl2O3 nanofluid in a circular tube submitted to a constant and uniform heat flux at the wall is numerically investigated. A single and two-phase model (discrete particles model) is employed with either constant or temperature-dependent properties. The investigation is accomplished for a size particles equal to 100 nm. Convective heat transfer coefficient for nanofluids is greater than that of the base liquid. Heat transfer enhancement is increasing with the particle volume concentration but it is accompanied by increasing wall shear stress values. The effect of Reynolds number is greater when properties depend on temperature and for higher concentrations.

Numerical Investigation of Forced Convection of Nanofluids in Channels

2008 ◽  
Author(s):  
Vincenzo Bianco ◽  
Oronzio Manca ◽  
Ferdinando Marzano ◽  
Sergio Nardini ◽  
Salvatore Tamburrino ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Forced Convection ◽  
Convective Heat Transfer Coefficient ◽  
Convection Flow ◽  
Uniform Heat Flux ◽  
Particle Volume ◽  
Two Phase ◽  
Square Channel

In this paper developing turbulent forced convection flow of a water–Al2O3 nanofluid in a square channel submitted to a constant and uniform heat flux at the wall is numerically investigated. A single model and two-phase models (discrete particles model and mixture model) are employed with constant temperature properties. The investigation is accomplished for a size particles equal to 38 nm. The CFD commercial code Fluent is employed to solve the problem by means of finite volume method. Convective heat transfer coefficient for nanofluids is greater than that of the base liquid. Heat transfer enhancement is increasing with the particle volume concentration but it is accompanied by increasing wall shear stress values. The effect of Reynolds number is great for higher concentrations. The results obtained by tree different models are presented in terms of temperatures and velocity distributions, relative increasing of heat transfer coefficient, hr, and Nusselt number profile.

scholarly journals Conjugate heat transfer performance of stepped lid-driven cavity with Al2O3/water nanofluid under forced and mixed convection

2021 ◽  
Vol 3 (6) ◽  
Author(s):  
Naveen Janjanam ◽  
Rajesh Nimmagadda ◽  
Lazarus Godson Asirvatham ◽  
R. Harish ◽  
Somchai Wongwises
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Mixed Convection ◽  
Conjugate Heat Transfer ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Interface Temperature ◽  
Transfer Model ◽  
Transfer Performance ◽  
Driven Cavity

AbstractTwo-dimensional conjugate heat transfer performance of stepped lid-driven cavity was numerically investigated in the present study under forced and mixed convection in laminar regime. Pure water and Aluminium oxide (Al2O3)/water nanofluid with three different nanoparticle volume concentrations were considered. All the numerical simulations were performed in ANSYS FLUENT using homogeneous heat transfer model for Reynolds number, Re = 100 to 500 and Grashof number, Gr = 5000, 13,000 and 20,000. Effective thermal conductivity of the Al2O3/water nanofluid was evaluated by considering the Brownian motion of nanoparticles which results in 20.56% higher value for 3 vol.% Al2O3/water nanofluid in comparison with the lowest thermal conductivity value obtained in the present study. A solid region made up of silicon is present underneath the fluid region of the cavity in three geometrical configurations (forward step, backward step and no step) which results in conjugate heat transfer. For higher Re values (Re = 500), no much difference in the average Nusselt number (Nuavg) is observed between forced and mixed convection. Whereas, for Re = 100 and Gr = 20,000, Nuavg value of mixed convection is 24% higher than that of forced convection. Out of all the three configurations, at Re = 100, forward step with mixed convection results in higher heat transfer performance as the obtained interface temperature is lower than all other cases. Moreover, at Re = 500, 3 vol.% Al2O3/water nanofluid enhances the heat transfer performance by 23.63% in comparison with pure water for mixed convection with Gr = 20,000 in forward step.

Quantitative Experimental Study of SiO2-Water Nanofluids on Backward-Facing Step Flow under Low Reynolds Number

2018 ◽  
Vol 916 ◽  
pp. 221-225
Author(s):  
Ji Zu Lv ◽  
Liang Yu Li ◽  
Cheng Zhi Hu ◽  
Min Li Bai ◽  
Sheng Nan Chang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Reynolds Number ◽  
Volume Fraction ◽  
Pure Water ◽  
Experimental Studies ◽  
Flow Characteristics ◽  
Thermal Engineering ◽  
Heat Transfer Medium ◽  
Step Flow

Nanofluids is an innovative study of nanotechnology applied to the traditional field of thermal engineering. It refers to the metal or non-metallic nanopowder was dispersed into water, alcohol, oil and other traditional heat transfer medium, to prepared as a new heat transfer medium with high thermal conductivity. The role of nanofluids in strengthening heat transfer has been confirmed by a large number of experimental studies. Its heat transfer mechanism is mainly divided into two aspects. On the one hand, the addition of nanoparticles enhances the thermal conductivity. On the other hand, due to the interaction between the nanoparticles and base fluid causing the changes in the flow characteristics, which is also the main factor affecting the heat transfer of nanofluids. Therefore, a intensive study on the flow characteristics of nanofluids will make the study of heat transfer more meaningful. In this experiment, the flow characteristics of SiO2-water nanofluids in two-dimensional backward step flow are quantitatively studied by PIV. The results show that under the same Reynolds number, the turbulence of nanofluids is larger than that of pure water. With the increase of nanofluids volume fraction, the flow characteristics are constantly changing. The quantitative analysis proved that the nanofluids disturbance was enhanced compared with the base liquid, which resulting in the heat transfer enhancement.

scholarly journals Joule heating effect on magnetohydrodynamic natural convection flow along a vertical wavy surface

2012 ◽  
Vol 9 (1) ◽  
pp. 11-24 ◽  
Author(s):  
Nazma Parveen ◽  
M A Alim
Keyword(s):  
Natural Convection ◽  
Joule Heating ◽  
Skin Friction Coefficient ◽  
Wavy Surface ◽  
Convection Flow ◽  
Surface Shear Stress ◽  
Natural Convection Flow ◽  
Surface Shear ◽  
Boundary Layer Equations ◽  
Marine Engineering

In this paper, the effect of Joule heating on magnetohydrodynamic natural convection flow of viscous incompressible fluid along a uniformly heated vertical wavy surface has been investigated. The governing boundary layer equations with associated boundary conditions for this phenomenon are converted to nondimensional form using a suitable transformation. The equations are mapped into the domain of a vertical flat plate and then solved numerically employing the implicit finite difference method, known as the Keller-box scheme. Effects of pertinent parameters, such as the Joule heating parameter (J), Prandtl number (Pr), magnetic parameter (M) and the amplitude of the wavy surface ? on the surface shear stress in terms of the skin friction coefficient (Cfx), the rate of heat transfer in terms of local Nusselt number (Nux), the streamlines and the isotherms are discussed. A comparison with previously published work is performed and the results show excellent agreement. DOI: http://dx.doi.org/10.3329/jname.v9i1.5954 Journal of Naval Architecture and Marine Engineering 9(2012) 11-24

Sign in / Sign up

Export Citation Format

Share Document