Comparing Methods for Establishing Multiscale Material Properties of 0.2 mm Thick Annealed ASTM 304

2015 ◽  
Author(s):  
William J. Emblom ◽  
Md. F. S. Ibne Islam ◽  
Richard J. Jones ◽  
Mitra Aithal ◽  
Scott Wagner ◽  
...  
Keyword(s):  
Finite Element ◽  
Sheet Metal ◽  
Material Properties ◽  
Strain Measurement ◽  
Measurement Errors ◽  
Element Model ◽  
Experimental Results ◽  
304 Stainless Steel ◽  
Membrane Theory ◽  
Forming Process

Producing fuel cells bipolar plates and other devices such as microscale heat exchangers for electronics requires both macroscale and microscale forming processes. At the macroscale, typically, mechanical properties of sheet metal are determined by performing tensile tests. In addition, it has long been recognized that bi-axial tension tests, dome tests, and hydroforming or viscous bulge tests provide the basis for improved understanding of the mechanics of sheet metal forming. At the microscale strain gauges are too large for measuring strains in small regions and membrane theory is only valid at the poles of the bulge. Continuum mechanics models are useful but require tedious thickness measurements for multiple work pieces, requiring extensive sample preparation and analysis. In this paper experimental results from hydroforming tests for 0.2-mm thick annealed ASTM 304 stainless steel sheet in 11 mm, 5 mm, and 1 mm diameter open dies at various pressures were evaluated. The height of the bulge at the pole and strains based upon measurements of 127 micron strain grids were determined. These dies represent the transition from a small macroscale process to a microscale forming process. Two methods were used to estimate material properties: an analytical model and an iterative method which compared experimental strain results with the strains from a finite element model where the Holloman constitutive properties of the sheet were varied. The problems estimating material properties based upon grid strain measurement, membrane theory, and the iterative finite element approaches were investigated and the results were compared. This study indicates that membrane theory will provide adequate predictions for Holloman constructive properties provided the assumptions for membrane theory are not violated. However, using measured microscale grid deformation strains does not produce very good agreement estimates of the Holloman constitutive model when comparing experimental results with FEA strains. It is believed that while the grid strain measurement method used results in strain measurement errors of less than 1.5% of strain, this error is sufficient to result in enough uncertainty to produce results that are inconsistent with other methods.

Sheet Metals Forming Die Design Using Finite Element Analysis and the Taguchi Method

2014 ◽  
Vol 621 ◽  
pp. 195-201
Author(s):  
Surangsee Dechjarern ◽  
Maitri Kamonrattanapisut
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Friction Coefficient ◽  
Taguchi Method ◽  
Finite Element Model ◽  
Sheet Metal ◽  
Element Model ◽  
Die Design ◽  
Forming Process ◽  
Element Analysis

Sheet metal deep-draw die is primarily constructed with draw bead, which is then modified based on trial and error to obtain a successful forming without splitting. This work aims at a robust design of forming die using numerical analysis and the Taguchi method. A three dimensional elastoplastic finite element model of a sheet metal forming process of SPCEN steel has been successfully developed using the material flow stress obtained from the modified Erichsen cup test. The model was validated with the actual forming experiment and the results agreed well. The influence of draw bead parameters on splitting and thinning distributions were examined using the Taguchi method. Four parameters, namely the friction coefficient, draw bead height, radius and shoulder radius were investigated. The Taguchi main effect analysis and ANOVA results show that the height and shoulder radius of the draw bead are the most important factor influencing the thinning distribution. Applying the Taguchi method and using the minimum thinning percentage as the design criteria, the optimum die design was identified as height, radius, shoulder radius and the friction coefficient of 4, 8, 8 mm and 0.125 respectively. The verified finite element model using the optimum die design was conducted. The predicted Taguchi response was within 5.9% from finite element analysis prediction. The improvement in the reduction of thinning percentage was 22.35%.

Numerical Simulation for the Multi-Point Incremental Forming Process

2015 ◽  
Vol 775 ◽  
pp. 219-223
Author(s):  
Wan Mian Yang ◽  
Yuan Xin Luo ◽  
Zhi Fang Liu ◽  
Ru Xu Du
Keyword(s):  
Numerical Simulation ◽  
Finite Element ◽  
Finite Element Model ◽  
Sheet Metal ◽  
Incremental Forming ◽  
Element Model ◽  
Sheet Metals ◽  
Forming Force ◽  
Forming Process ◽  
Thickness Change

Multi-point forming process has been developed to shape the sheet metal with bidirectional curvature. However, the forming force usually climbs too high so that the dimension of the forming machine should be designed to meet it. To solve this problem, the multi-point incremental forming (MPIF) process was proposed in this paper. First, the principle of this new forming process was introduced. Then, the experimental device was designed. Next, the MPIF process was simulated by a finite element model. The forming effects including displacements, thickness, and curvatures were visualized and discussed in detail. It was found that there is no obvious thickness change during the forming process. The advantage of this forming process is that the shape of the sheet metals adaptable and controllable with small forming force.

scholarly journals PENGARUH MODEL DAN SIFAT MATERIAL PADA ANALISIS METODE ELEMEN HINGGA BALOK TABUNG BAJA BUNDAR DIIISI BETON

2017 ◽  
Vol 19 (2) ◽  
pp. 106-114
Author(s):  
Mahmud Kori Effendi
Keyword(s):  
Finite Element ◽  
Material Properties ◽  
Plastic Hinge ◽  
Three Dimensional ◽  
Element Model ◽  
Experimental Results ◽  
Steel Tubes ◽  
Element Analysis ◽  
Non Linear ◽  
Three Dimensional Finite Element

The composite material concrete filled steel tubes, CFST) begin widely recommended in modern structural projects. This material is made of steel tubes filled with concrete. This CFST structure has better ductility than the conventional structure. The three-dimensional finite element modelby means of MSC Marc Mentat software is done by using non-linear material properties for both the steel and concrete. The non-linear geometry is also considered. The results of the finite element analysis method are then compared with experimental results of circular steel tubes filled with concrete. The results of this analysis for both load-deflection and collapse conditions are quite agree with the experimental results. However, the buckling phenomena cannot be modeled in the analysis of the finite element method. The effect of finite element model, which is half span and a quarter of half span, is investigated. The results of this analysis are similar to the results of full-scale analysis. There is plastic hinge in the middle of the beam span. The influence of the material properties of linear and non-linear geometric properties are also investigated. The the plastic hinge did not occur in the middle of beam span.

Determination of Charge Coefficient of Piezoelectric Films Using a Combined Finite Element Model and Dynamic Loading Technique

2020 ◽  
Vol 835 ◽  
pp. 229-242
Author(s):  
Oboso P. Bernard ◽  
Nagih M. Shaalan ◽  
Mohab Hossam ◽  
Mohsen A. Hassan
Keyword(s):  
Finite Element ◽  
Dynamic Loading ◽  
Material Properties ◽  
Accurate Determination ◽  
Substrate Material ◽  
Experimental Results ◽  
Piezoelectric Composite ◽  
Piezoelectric Film ◽  
Piezoelectric Charge

Accurate determination of piezoelectric properties such as piezoelectric charge coefficients (d33) is an essential step in the design process of sensors and actuators using piezoelectric effect. In this study, a cost-effective and accurate method based on dynamic loading technique was proposed to determine the piezoelectric charge coefficient d33. Finite element analysis (FEA) model was developed in order to estimate d33 and validate the obtained values with experimental results. The experiment was conducted on a piezoelectric disc with a known d33 value. The effect of measuring boundary conditions, substrate material properties and specimen geometry on measured d33 value were conducted. The experimental results reveal that the determined d33 coefficient by this technique is accurate as it falls within the manufactures tolerance specifications of PZT-5A piezoelectric film d33. Further, obtained simulation results on fibre reinforced and particle reinforced piezoelectric composite were found to be similar to those that have been obtained using more advanced techniques. FE-results showed that the measured d33 coefficients depend on measuring boundary condition, piezoelectric film thickness, and substrate material properties. This method was proved to be suitable for determination of d33 coefficient effectively for piezoelectric samples of any arbitrary geometry without compromising on the accuracy of measured d33.

Comparison between an Advanced Numerical Simulation of Sheet Incremental Forming Using Adaptive Remeshing and Experimental Results

2013 ◽  
Vol 554-557 ◽  
pp. 1375-1381 ◽  
Author(s):  
Laurence Giraud-Moreau ◽  
Abel Cherouat ◽  
Jie Zhang ◽  
Houman Borouchaki
Keyword(s):  
Numerical Simulation ◽  
Numerical Model ◽  
Sheet Metal ◽  
Metal Forming ◽  
Tool Path ◽  
Incremental Forming ◽  
Computation Time ◽  
Experimental Results ◽  
Forming Process ◽  
Adaptive Remeshing

Recently, new sheet metal forming technique, incremental forming has been introduced. It is based on using a single spherical tool, which is moved along CNC controlled tool path. During the incremental forming process, the sheet blank is fixed in sheet holder. The tool follows a certain tool path and progressively deforms the sheet. Nowadays, numerical simulations of metal forming are widely used by industry to predict the geometry of the part, stresses and strain during the forming process. Because incremental forming is a dieless process, it is perfectly suited for prototyping and small volume production [1, 2]. On the other hand, this process is very slow and therefore it can only be used when a slow series production is required. As the sheet incremental forming process is an emerging process which has a high industrial interest, scientific efforts are required in order to optimize the process and to increase the knowledge of this process through experimental studies and the development of accurate simulation models. In this paper, a comparison between numerical simulation and experimental results is realized in order to assess the suitability of the numerical model. The experimental investigation is realized using a three-axis CNC milling machine. The forming tool consists in a cylindrical rotating punch with a hemispherical head. A subroutine has been developed to describe the tool path from CAM procedure. A numerical model has been developed to simulate the sheet incremental forming process. The finite element code Abaqus explicit has been used. The simulation of the incremental forming process stays a complex task and the computation time is often prohibitive for many reasons. During this simulation, the blank is deformed by a sequence of small increments that requires many numerical increments to be performed. Moreover, the size of the tool diameter is generally very small compared to the size of the metal sheet and thus the contact zone between the tool and the sheet is limited. As the tool deforms almost every part of the sheet, small elements are required everywhere in the sheet resulting in a very high computation time. In this paper, an adaptive remeshing method has been used to simulate the incremental forming process. This strategy, based on adaptive refinement and coarsening procedures avoids having an initially fine mesh, resulting in an enormous computing time. Experiments have been carried out using aluminum alloy sheets. The final geometrical shape and the thickness profile have been measured and compared with the numerical results. These measurements have allowed validating the proposed numerical model. References [1] M. Yamashita, M. Grotoh, S.-Y. Atsumi, Numerical simulation of incremental forming of sheet metal, J. Processing Technology, No. 199 (2008), p. 163 172. [2] C. Henrard, A.M. Hbraken, A. Szekeres, J.R. Duflou, S. He, P. Van Houtte, Comparison of FEM Simulations for the Incremental Forming Process, Advanced Materials Research, 6-8 (2005), p. 533-542.

Flexible Stretch Forming Technology for Sheet Metal Based on Discrete-Gripper and Multi-Point Die

2014 ◽  
Vol 556-562 ◽  
pp. 460-463 ◽  
Author(s):  
Xue Chen ◽  
Ming Zhe Li ◽  
Wen Hua Liu ◽  
Zhi Qiang Hou
Keyword(s):  
Sheet Metal ◽  
Experimental Results ◽  
Shape Error ◽  
Stretch Forming ◽  
Forming Process ◽  
Structural Composition ◽  
Forming Technology ◽  
Working Principle ◽  
Material Utilization

To solve the problem of low material utilization in traditional stretch forming process, a flexible stretch forming method was proposed, which can be realized by interaction of the multi-point stretch forming die with discrete-gripper stretch forming machine. The principle and characteristics of sheet metal flexible stretch forming technology was introduced, structural composition and working principle of the multi-point stretch forming die and discrete-gripper stretch forming machine were expounded, and the technology experiments was carried out with a self-designed flexible stretch forming technology equipment for sheet metal. The experimental results indicate that structure of multi-point stretch forming die and discrete-gripper stretch forming machine are reasonable, and flexible stretch forming technology can be realized by above-mentioned die and machine, stretch forming parts has a good quality and its shape error can satisfy requirements of production.

FEBio finite element model of a pediatric cervical spine

2021 ◽  
pp. 1-7
Author(s):  
Sean M. Finley ◽  
J. Harley Astin ◽  
Evan Joyce ◽  
Andrew T. Dailey ◽  
Douglas L. Brockmeyer ◽  
...  
Keyword(s):  
Finite Element ◽  
Cervical Spine ◽  
Finite Element Model ◽  
Material Properties ◽  
Surgical Simulation ◽  
Element Model ◽  
Axial Stiffness ◽  
Published Data ◽  
Axial Tension ◽  
Flexion Extension

OBJECTIVE The underlying biomechanical differences between the pediatric and adult cervical spine are incompletely understood. Computational spine modeling can address that knowledge gap. Using a computational method known as finite element modeling, the authors describe the creation and evaluation of a complete pediatric cervical spine model. METHODS Using a thin-slice CT scan of the cervical spine from a 5-year-old boy, a 3D model was created for finite element analysis. The material properties and boundary and loading conditions were created and model analysis performed using open-source software. Because the precise material properties of the pediatric cervical spine are not known, a published parametric approach of scaling adult properties by 50%, 25%, and 10% was used. Each scaled finite element model (FEM) underwent two types of simulations for pediatric cadaver testing (axial tension and cardinal ranges of motion [ROMs]) to assess axial stiffness, ROM, and facet joint force (FJF). The authors evaluated the axial stiffness and flexion-extension ROM predicted by the model using previously published experimental measurements obtained from pediatric cadaveric tissues. RESULTS In the axial tension simulation, the model with 50% adult ligamentous and annulus material properties predicted an axial stiffness of 49 N/mm, which corresponded with previously published data from similarly aged cadavers (46.1 ± 9.6 N/mm). In the flexion-extension simulation, the same 50% model predicted an ROM that was within the range of the similarly aged cohort of cadavers. The subaxial FJFs predicted by the model in extension, lateral bending, and axial rotation were in the range of 1–4 N and, as expected, tended to increase as the ligament and disc material properties decreased. CONCLUSIONS A pediatric cervical spine FEM was created that accurately predicts axial tension and flexion-extension ROM when ligamentous and annulus material properties are reduced to 50% of published adult properties. This model shows promise for use in surgical simulation procedures and as a normal comparison for disease-specific FEMs.

Effect of Ramp Angle on the Anti-Loosening Ability of Wedge Self-Locking Nuts Under Vibration

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
Jianhua Liu ◽  
Hao Gong ◽  
Xiaoyu Ding
Keyword(s):  
Finite Element ◽  
Numerical Simulations ◽  
Production Technology ◽  
Material Properties ◽  
Threshold Value ◽  
Commercial Production ◽  
Experimental Results ◽  
Fe Method ◽  
Transversal Vibration

Recently, the wedge self-locking nut, a special anti-loosening product, is receiving more attention because of its excellent reliability in preventing loosening failure under vibration conditions. The key characteristic of a wedge self-locking nut is the special wedge ramp at the root of the thread. In this work, the effect of ramp angle on the anti-loosening ability of wedge self-locking nuts was studied systematically based on numerical simulations and experiments. Wedge self-locking nuts with nine ramp angles (10 deg, 15 deg, 20 deg, 25 deg, 30 deg, 35 deg, 40 deg, 45 deg, and 50 deg) were modeled using a finite element (FE) method, and manufactured using commercial production technology. Their anti-loosening abilities under transversal vibration conditions were analyzed based on numerical and experimental results. It was found that there is a threshold value of the initial preload below which the wedge self-locking nuts would lose their anti-loosening ability. This threshold value of initial preload was then proposed for use as a criterion to evaluate the anti-loosening ability of wedge self-locking nuts quantitatively and to determine the optimal ramp angle. Based on this criterion, it was demonstrated, numerically and experimentally, that a 30 deg wedge ramp resulted in the best anti-loosening ability among nine ramp angles studied. The significance of this study is that it provides an effective method to evaluate the anti-loosening ability of wedge self-locking nuts quantitatively, and determined the optimal ramp angle in terms of anti-loosening ability. The proposed method can also be used to optimize other parameters, such as the material properties and other dimensions, to guarantee the best anti-loosening ability of wedge self-locking nuts.

Sign in / Sign up

Export Citation Format

Share Document