Nondestructive Evaluation of Thermal Fatigue Crack Propagation in Sn-Ag-Cu Solder Joints by Synchrotron Radiation X-Ray Micro-Tomography

2009 ◽  
Author(s):  
Hiroyuki Tsuritani ◽  
Toshihiko Sayama ◽  
Yoshiyuki Okamoto ◽  
Takeshi Takayanagi ◽  
Kentaro Uesugi ◽  
...  
Keyword(s):  
Crack Propagation ◽  
Nondestructive Evaluation ◽  
Thermal Cycle ◽  
Solder Joints ◽  
Fatigue Cracks ◽  
Lead Free Solder ◽  
X Ray ◽  
Solder Bumps ◽  
Micro Tomography ◽  
Free Solder

An X-ray micro-tomography system called SP-μCT, which has a spatial resolution of 1 μm, has been developed in SPring-8, the largest synchrotron radiation facility in Japan. In this work, SP-μCT was applied to the nondestructive evaluation of micro-crack propagation appearing as thermal fatigue damage in lead-free solder joints. The observed specimens include two typical micro-joint structures by Sn-3.0wt%Ag-0.5wt%Cu lead-free solder. The first is an FBGA (Fine pitch Ball Grid Array) joint specimen in which an LSI package is connected to a substrate by solder bumps 360 μm in diameter, while the second is a chip joint specimen in which chip type resistors 1.6 mm in length and 0.8 mm. in width are mounted on a substrate. A thermal cycle test was carried out, and the specimens were picked up at fixed cycle numbers. The same solder joints were observed repeatedly using SP-μCT at beamline BL20XU in SPring-8. An X-ray energy of 29.0 keV was selected to obtain CT (Computed Tomography) images with high contrast among some components, and a refraction-contrast imaging technique was also applied to the visualization of fatigue cracks in the solder joints. In the FBGA type specimens, fatigue cracks appeared at the periphery of the interfaces between the solder and the UBM (Under Bump Metallization) on the LSI package. As the thermal cycle proceeds, the cracks propagate gradually to the inner region of the solder bumps in the vicinity of the interface. On the basis of the three-dimensional crack images, the fatigue crack propagation lifetime was accurately estimated by means of the average crack propagation rate. On the other hand, in the chip joint specimens, fatigue cracks appeared and propagated through the thin solder layer between the chip and substrate. In contrast to the FBGA specimen, many small voids roughly 5 to 10 μm in length were formed in the solder layer. The important observed fact is that these voids deform and connect to each other due to the thermal cyclic loading prior to crack propagation. Consequently, the obtained CT images clearly show the process of crack propagation due to the thermal cyclic loading of the same solder joint. In contrast, such information has not been obtained, whatsoever by industrially employed X-ray CT systems.

Quantitative Evaluation of Voids in Lead Free Solder Joints

2015 ◽  
Vol 772 ◽  
pp. 284-289 ◽  
Author(s):  
Sabuj Mallik ◽  
Jude Njoku ◽  
Gabriel Takyi
Keyword(s):  
Solder Bump ◽  
Solder Joints ◽  
Void Formation ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Paste ◽  
X Ray ◽  
Size And Shape ◽  
Solder Bumps ◽  
Free Solder

Voiding in solder joints poses a serious reliability concern for electronic products. The aim of this research was to quantify the void formation in lead-free solder joints through X-ray inspections. Experiments were designed to investigate how void formation is affected by solder bump size and shape, differences in reflow time and temperature, and differences in solder paste formulation. Four different lead-free solder paste samples were used to produce solder bumps on a number of test boards, using surface mount reflow soldering process. Using an advanced X-ray inspection system void percentages were measured for three different size and shape solder bumps. Results indicate that the voiding in solder joint is strongly influenced by solder bump size and shape, with voids found to have increased when bump size decreased. A longer soaking period during reflow stage has negatively affectedsolder voids. Voiding was also accelerated with smaller solder particles in solder paste.

Nondestructive Observation of Thermal Fatigue Crack Propagation in FBGA and Die Attached Solder Joints by Synchrotron Radiation X-Ray Laminography

2015 ◽  
Author(s):  
Hiroyuki Tsuritani ◽  
Toshihiko Sayama ◽  
Yoshiyuki Okamoto ◽  
Takeshi Takayanagi ◽  
Masato Hoshino ◽  
...  
Keyword(s):  
Fatigue Crack ◽  
Synchrotron Radiation ◽  
Crack Propagation ◽  
Thermal Fatigue ◽  
Solder Joints ◽  
Fatigue Cracks ◽  
Three Dimensional ◽  
X Ray ◽  
Micro Cracks ◽  
Solder Bumps

The reliability of solder joints on printed circuit boards (PCBs) is significantly affected by thermal fatigue processes due to downsizing and high density packaging in electronic components. Accordingly, there is a strong desire in related industries for development of a new nondestructive inspection technology to detect fatigue cracks appearing in these joints. The authors have applied the SP-μCT, a synchrotron radiation X-ray microtomography system, to the nondestructive observation of such cracks. However, for planar objects such as PCB substrates, reconstruction of CT images is difficult due to insufficient X-ray transmission along the parallel axis of the substrate. In order to solve this problem, a synchrotron radiation X-ray laminography system was developed to overcome the size limits of such specimens. In this work, this system was applied to the three-dimensional, nondestructive observation of thermal fatigue cracks in solder joints, for which X-ray CT inspection has been extremely difficult. The observed specimens included two typical joint structures formed using Sn-3.0Ag-0.5Cu solder: (1) a fine pitch ball grid array (FBGA) joint specimen in which an LSI package is connected to a substrate by solder bumps 360 μm in diameter, and (2) a die-attached specimen in which a 3 mm square ceramic chip is mounted on a substrate. The optical system developed for use in X-ray laminography was constructed to provide a rotation axis with a 30° tilt from the right angle to the X-ray beam, and to obtain X-ray projection images via the beam monitor. The same solder joints were observed successively using the laminography system at beamline BL20XU at SPring-8, the largest synchrotron radiation facility in Japan. In the FBGA type specimen, fatigue cracks were clearly observed to appear at the periphery of the joint interface, and to propagate gradually to the inner regions of the solder bumps as thermal cycling proceeded. In contrast, in the die-attached joint specimen, micro-cracks were observed to appear and propagate through the thin solder layer. An important observation was that these micro-cracks become interconnected prior to propagation of the main fatigue crack. The fatigue crack propagation lifetime was also estimated in both specimens by measuring the crack surface area and calculating the average crack propagation rate through the three-dimensional images. Consequently, the sectional images obtained by the laminography system clearly show the process of crack propagation due to thermal cyclic loading.

SAC–xTiO2 nano-reinforced lead-free solder joint characterizations in ultra-fine package assembly

2018 ◽  
Vol 30 (1) ◽  
pp. 1-13 ◽  
Author(s):  
Fakhrozi Che Ani ◽  
Azman Jalar ◽  
Abdullah Aziz Saad ◽  
Chu Yee Khor ◽  
Roslina Ismail ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Solder Joint ◽  
Solder Joints ◽  
Ion Beam ◽  
Lead Free ◽  
Lead Free Solder ◽  
Solder Paste ◽  
Content Type ◽  
X Ray ◽  
Free Solder

Purpose This paper aims to investigate the characteristics of ultra-fine lead-free solder joints reinforced with TiO2 nanoparticles in an electronic assembly. Design/methodology/approach This study focused on the microstructure and quality of solder joints. Various percentages of TiO2 nanoparticles were mixed with a lead-free Sn-3.5Ag-0.7Cu solder paste. This new form of nano-reinforced lead-free solder paste was used to assemble a miniature package consisting of an ultra-fine capacitor on a printed circuit board by means of a reflow soldering process. The microstructure and the fillet height were investigated using a focused ion beam, a high-resolution transmission electron microscope system equipped with an energy dispersive X-ray spectrometer (EDS), and a field emission scanning electron microscope coupled with an EDS and X-ray diffraction machine. Findings The experimental results revealed that the intermetallic compound with the lowest thickness was produced by the nano-reinforced solder with a TiO2 content of 0.05 Wt.%. Increasing the TiO2 content to 0.15 Wt.% led to an improvement in the fillet height. The characteristics of the solder joint fulfilled the reliability requirements of the IPC standards. Practical implications This study provides engineers with a profound understanding of the characteristics of ultra-fine nano-reinforced solder joint packages in the microelectronics industry. Originality/value The findings are expected to provide proper guidelines and references with regard to the manufacture of miniaturized electronic packages. This study also explored the effects of TiO2 on the microstructure and the fillet height of ultra-fine capacitors.

Effect of Micro Structure on Fatigue Characteristics of Lead Free Solder Joints

2011 ◽  
Author(s):  
Takahiro Akutsu ◽  
Qiang Yu
Keyword(s):  
Grain Size ◽  
Fatigue Crack ◽  
Fatigue Life ◽  
Solder Joint ◽  
Crack Propagation ◽  
Solder Joints ◽  
Lead Free ◽  
Lead Free Solder ◽  
Micro Structure ◽  
Free Solder

This paper presents the influence of the micro structure on the crack propagation in lead free solder joint. The author’s group have studied the Manson-Coffin’s law for lead free solder joint by using the isothermal fatigue test and FEM analytical approaches to establish the practicable evaluation of thermal fatigue life of solder joints, for example, for the Sn-Cu-Ni solder, because this solder is attracted from the aspect of the decrease of solder leach in the flow process and material cost. However, even if the same loading is given to the solder joints of BGA test piece, there was a large dispersion in the fatigue life. Even though the effect of the shape difference has been considered, the range of the dispersion could not been explained sufficiently. In the study, the fatigue crack propagation modes in the solder joints were investigated, and an internal fatigue crack mode and an interfacial fatigue crack mode were confirmed. And the tendency of a shorter on fatigue life in the interfacial fatigue mode was confirmed. To clarify the mechanism of these fatigue crack modes, the crystal grain size in the solder joints was investigated before the fatigue test and also after the test. Furthermore, the verification of the mechanism using FEM models considering the crystal grain size was carried out. First of all, each element in FEM models matching to the average crystal grain size was made. Second, the inelastic strain ranges in each FEM models were studied. As a result, it was shown that the influence of the crude density of the crystal grain to the fatigue crack progress can be evaluated. In addition, the micro structure of the solder joint of large-scale electronic devices is observed, and FEM model was made based on the observation result. As a result, it was shown that the influence of the directionality with the crystal grain to the fatigue crack progress can be evaluated.

scholarly journals Correlation Between Pin Misalignment and Crack Length in THT Solder Joints

2017 ◽  
Vol 62 (2) ◽  
pp. 1063-1066
Author(s):  
A. Molnar ◽  
M. Benke ◽  
Z. Gacsi
Keyword(s):  
Crack Propagation ◽  
Crack Length ◽  
Thermal Shock ◽  
Solder Joints ◽  
Lead Free ◽  
Temperature Profiles ◽  
Lead Free Solder ◽  
Solder Alloys ◽  
Free Solder

AbstractIn this manuscript, correlations were searched for between pin misalignments relative to PCB bores and crack propagation after cyclic thermal shock tests in THT solder joints produced from lead-free solder alloys. In total, 7 compositions were examined including SAC solders with varying Ag, Cu and Ni contents. The crack propagation was initiated by cyclic thermal shock tests with 40°C / +125°C temperature profiles. Pin misalignments relative to the bores were characterized with three attributes obtained from one section of the examined solder joints. Cracks typically originated at the solder/pin or solder/bore interfaces and propagated within the solder. It was shown that pin misalignments did not have an effect on crack propagation, thus, the solder joints’ lifetime.

Void Inspection in Lead-Free Solder Bumps on Ball Grid Array (BGA) Packages Using Laser Ultrasound Technique

2011 ◽  
Author(s):  
Jie Gong ◽  
I. Charles Ume
Keyword(s):  
Ball Grid Array ◽  
Lead Free ◽  
Inspection System ◽  
Laser Ultrasound ◽  
Lead Free Solder ◽  
X Ray ◽  
Bga Packages ◽  
Solder Bumps ◽  
Free Solder ◽  
Ultrasound Inspection

Solder joint voids are usually formed by the entrapped gas bubbles during the reflow process, and are common in all surface mount applications. It is a controversial issue on the reliability of the solder joint, however the consensus is that voiding is acceptable at low contents, while excessive voiding affects mechanical properties, and decreases strength, ductility and fatigue life of the interconnections. X-ray is the most widely used technique to evaluate the voids, including the size and occurrence frequency. In this paper, a laser ultrasound and interferometer inspection system is used to inspect the voids in lead-free solder bumps in ball grid array (BGA) packages. This system uses a pulsed Nd:YAG laser to induce ultrasound in the chip packages in the thermoelastic regime; and laser interferometer is used to measure the transient out-of-plane displacement response of the package surface to the laser irradiation. The quality of solder bumps is evaluated by analyzing the transient responses. In this work, voids were intentionally created by adding the volatile flux during the assembly process. By controlling the volume of flux dip, three different levels of voiding were proposed: void-free, relatively low and relatively high. The presence of voids in the solder bumps was first verified using 2-D X-ray techniques. Meanwhile, the built-in image-processing software in X-ray tool measured the void fraction to quantify the level of voiding. Then the laser ultrasound inspection system was used to evaluate the voids in these samples. By comparing the vibration responses from voided samples and void-free samples, it was found that the laser ultrasound inspection system is capable to differentiate samples with relatively high voiding from void-free samples while the relatively low voiding was below the resolution of the inspection system. Lastly, a further comparison between the void-free and voided solder bumps was carried out by the destructive cross-section technique. The comparisons between these three solder bump evaluation methods will be presented in this paper.

Application of Synchrotron Radiation X-Ray Microtomography to Nondestructive Evaluation of Thermal Fatigue Process in Flip Chip Interconnects

2011 ◽  
Vol 133 (2) ◽  
Author(s):  
Hiroyuki Tsuritani ◽  
Toshihiko Sayama ◽  
Yoshiyuki Okamoto ◽  
Takeshi Takayanagi ◽  
Kentaro Uesugi ◽  
...  
Keyword(s):  
Synchrotron Radiation ◽  
Crack Propagation ◽  
Nondestructive Evaluation ◽  
Thermal Fatigue ◽  
Flip Chip ◽  
Fatigue Cracks ◽  
Nondestructive Inspection ◽  
Ct Images ◽  
Phase Growth ◽  
X Ray

New nondestructive inspection methods with high spatial resolution are expected to support the evaluation and enhancement of the reliability of microjoints on printed circuit boards. An X-ray microtomography system, the SP-μCT has been developed at the Super Photon ring-8 GeV (SPring-8), the largest synchrotron radiation facility in Japan. In this work, the SP-μCT was first applied to the nondestructive evaluation of thermal fatigue phenomena, namely microstructure evolution (i.e., phase growth) and microcrack propagation, appearing in actual solder microbumps of flip chip interconnects due to thermal cyclic loading. In addition, a refraction-contrast imaging technique was simultaneously applied to visualize the fatigue cracks with an actual opening of less than 100 nm. The observed specimen has a flip chip structure joined by Sn-37wt%Pb eutectic solder bumps 150 μm in diameter. Consequently, the process of phase growth and crack propagation was determined via observation of consecutive computed tomography (CT) images obtained in the same plane of the same specimen. As the thermal cycle proceeded, remarkable phase growth was clearly observed, followed by the appearance of fatigue cracks in the corners of the interfaces between the solder bump and Cu pad. Moreover, the CT images also enabled us to evaluate the fatigue lifetime of the bumps, as follows. The lifetime to fatigue crack initiation was estimated by quantifying the increase in the phase growth. The crack propagation lifetime to failure was then determined by measuring the average crack propagation rate. Such results have not been obtainable at all by X-ray CT systems for industrial use and demonstrate the possibility of nondestructive inspection by a synchrotron radiation X-ray microtomography system.

Three Dimensional and Nondestructive Evaluation of Thermal Fatigue Crack Propagation Process in Complex-Shaped Solder Joints by Synchrotron Radiation X-Ray Micro-Tomography

2011 ◽  
Author(s):  
Hiroyuki Tsuritani ◽  
Toshihiko Sayama ◽  
Yoshiyuki Okamoto ◽  
Takeshi Takayanagi ◽  
Kentaro Uesugi ◽  
...  
Keyword(s):  
Fatigue Crack ◽  
Synchrotron Radiation ◽  
Crack Propagation ◽  
Fatigue Crack Propagation ◽  
Solder Joints ◽  
Fatigue Cracks ◽  
Propagation Process ◽  
X Ray ◽  
Micro Cracks ◽  
Crack Propagation Process

The reliability or lifetime of micro-joints on printed circuit boards (PCBs) is significantly affected by fatigue processes, including fatigue crack initiation and propagation to failure. Accordingly, the industries producing electronic devices and components strongly desire a new nondestructive inspection technology, which detects micro-cracks appearing as thermal fatigue fractures in the joints. In this investigation, we applied a synchrotron radiation X-ray micro-tomography system called the SP-μCT to three-dimensionally and nondestructively evaluate the fatigue crack propagation process in complex-shaped solder joints. The observed specimens have a typical joint structure in which chip type resistors 1.0 mm in length and 0.5 mm in width are mounted on an FR-4 substrate by joining with Sn-3.0Ag-0.5Cu solder. A thermal cycle test was carried out, and specimens were collected at fixed cycle numbers. The same solder joints were observed successively using the SP-μCT at beamline BL20XU at SPring-8, the largest synchrotron radiation facility in Japan. An X-ray energy of 29.0 keV was selected to obtain computed tomography (CT) images with high contrast among some components, and a refraction-contrast imaging technique was also applied to the visualization of fatigue cracks in the solder joints. The following results were obtained. At the early stage in the fatigue process of normal joints, the main fatigue cracks were clearly observed to initiate from the region around the solder joint tip and the vicinity of the chip corner. Additionally, many micro-cracks roughly 5 to 10 μm in length also formed in the thin solder layer between the chip and substrate. The important observed fact is that these micro-cracks deform, grow, and connect to each other due to the thermal cyclic loading, prior to main crack propagation. On the other hand, in case of solder joints which included relatively larger initial voids, the voids deformed, and the fatigue cracks initiated and propagated from the surface of the voids. Furthermore, by employing the three-dimensional crack images, the crack dimensions were quantified straightforwardly by measuring the surface area of the fatigue crack, and the fatigue crack propagation process was also accurately evaluated via the average crack propagation rate. Consequently, the obtained CT images clearly illustrate the process of crack propagation due to the thermal cyclic loading of a solder joint. In contrast, such information has not been obtained in any form by industrially employed X-ray CT systems or finite element analyses.

Sign in / Sign up

Export Citation Format

Share Document