scholarly journals Multi-Pass Weld Hydrogen Management to Prevent Delayed Cracking

2000 ◽  
Author(s):  
A. Dinovitzer ◽  
B. Graville ◽  
A. Glover ◽  
N. Pussegoda
Keyword(s):  
Material Selection ◽  
Base Material ◽  
Carbon Equivalent ◽  
Hydrogen Cracking ◽  
Tensile Stresses ◽  
General Base ◽  
Delayed Cracking ◽  
Welding Procedure ◽  
Welding Processes ◽  
Procedure Development

The potential for weld hydrogen cracking, that can also manifest itself as delayed cracking due to formation well after weld deposition, is controlled by three factors: the presence of hydrogen, the susceptibility of the weldment microstructure and tensile stresses. The tensile stresses promoting hydrogen cracking may result from either welding residual stresses or construction or operations based stresses, while the susceptibility of a microstructure is a function of its carbon equivalent and cooling rate. Since all arc welding processes introduce hydrogen into welds to some extent, and in general, base material selection and weld stress levels are not controllable in welding procedure development, the prevention of hydrogen cracking must be accomplished through hydrogen management. This paper describes a means of considering the roles of welding procedure parameters (heat input, preheat, post-heat, inter-pass temperature and time, etc.) in the management of hydrogen in multi-pass welds to preclude delayed cracking. Some results obtained using a multi-pass weld hydrogen and thermal diffusion model are presented to demonstrate the models utility in understanding the effects of welding procedure parameter effects on the risk of delayed cracking.

Development of an Effective ASME IX Welding Procedure Qualification Program for Pipeline Facility and Fabrication Welding

2016 ◽  
Author(s):  
Junfang Lu ◽  
Bob Huntley ◽  
Luke Ludwig
Keyword(s):  
Oil And Gas ◽  
Material Selection ◽  
Base Material ◽  
Welding Process ◽  
Notch Toughness ◽  
Essential Variable ◽  
Performance Qualification ◽  
Pipeline Welding ◽  
Welding Consumable ◽  
Welding Procedure

For cross country pipeline welding in Canada, welding procedures shall be qualified in accordance with the requirements of CSA Z662 Oil and Gas Pipeline Systems. For pipeline facility and fabrication welding on systems designed in accordance with CSA Z662 or ASME B31.4, welding procedures qualified in accordance with the requirements of ASME Boiler & Pressure Vessel Code Section IX are permitted and generally preferred. Welding procedures qualified in accordance with ASME IX provide advantages for pipeline facility and fabrication applications as a result of the flexibility achieved through the larger essential variable ranges. The resulting welding procedures have broader coverage on material thickness, diameter, joint configuration and welding positions. Similarly, ASME IX is more flexible on welder performance qualification requirements and accordingly a welder will have wider range of performance qualifications. When applied correctly, the use of ASME IX welding procedures often means significantly fewer welding procedures and welder performance qualifications are required for a given scope of work. Even though ASME IX qualified welding procedures have been widely used in pipeline facility and fabrication welding, it is not well understood on how to qualify the welding procedures in accordance with ASME IX and meet the additional requirements of the governing code or standard such as CSA Z662 in Canada. One significant consideration is that ASME IX refers to the construction code for the applicability of notch toughness requirements for welding procedure qualification, yet CSA Z662 and ASME B31.4 are both silent on notch toughness requirements for welding procedure qualification. This paper explains one preferred method to establish and develop an effective ASME IX welding procedure qualification program for pipeline facility and fabrication welding while ensuring suitability for use and appropriate notch toughness requirements. The paper discusses topics such as base material selection, welding process, welding consumable consideration and weld test acceptance criteria.

scholarly journals Structural Aspects of Execution and Thermal Treatment of Welded Joints of Hardox Extreme Steel

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 915 ◽  
Author(s):  
Konat
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Welded Joints ◽  
Base Material ◽  
Steel Structures ◽  
High Strength ◽  
Carbon Equivalent ◽  
Material Structure ◽  
Welding Processes ◽  
Structural Aspects

The paper presents structure and mechanical properties of welded joints of the high-strength, abrasive-wear resistant steel Hardox Extreme. It was shown that, as a result of welding this steel, structures conducive to lowering its abrasion-wear resistance are created in the heat-affected zone. Width of the zone exceeds 60 mm, which results in accelerated wear in the planned applications. On the grounds of the carried-out examinations of structures and selected mechanical properties, a welding technology followed by heat treatment of heat-affected zones was suggested, leading to reconstruction of HAZ structures that is morphologically close to the base material structure. In spite of high carbon equivalent (CEV) of Hardox Extreme, the executed welding processes and heat treatment did not result in the appearance, in laboratory conditions, of welding imperfections in the welded joints.

Determination of Critical Hydrogen Curves From Slow Bend Tests

2004 ◽  
Author(s):  
L. N. Pusseogda ◽  
A. Dinovitzer ◽  
D. Horsley
Keyword(s):  
Hydrogen Diffusion ◽  
High Strength Steels ◽  
High Strength ◽  
Hydrogen Diffusivity ◽  
Hydrogen Cracking ◽  
Cold Temperatures ◽  
Steel Strength ◽  
Delayed Cracking ◽  
Two Parameters ◽  
Welding Procedure

Recent trends in the pipeline industry are towards the use of high strength steels. As steel strength increases, the delayed hydrogen cracking propensity in the welds also increases. As welding is often completed during winter months, the cold temperatures must be considered in determining joining procedures that will avoid delayed hydrogen cracking. The Graville/BMT Fleet Technology Limited hydrogen diffusion and cracking models have been used successfully in the past to predict delayed cracking and to demonstrate how changes implemented in the welding procedure can minimize the risk of cracking. The two capabilities, hydrogen diffusion and cracking assessment, can be applied to the case of X100 pipe as well, provided the hydrogen diffusivity and the hydrogen cracking susceptibility curves are established for the materials of interest. These two parameters, the hydrogen diffusivity and the hydrogen cracking susceptibility curves are developed to examine the hydrogen cracking susceptibility of SMAW and GMAW welds in X100 pipe, and are the focus of the paper.

scholarly journals Technological, Microstructural and Strength Aspects of Welding and Post-Weld Heat Treatment of Martensitic, Wear-Resistant Hardox 600 Steel

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4541
Author(s):  
Łukasz Konat
Keyword(s):  
Heat Treatment ◽  
Welded Joints ◽  
Base Material ◽  
High Strength ◽  
Carbon Equivalent ◽  
Plastic Properties ◽  
Entire Area ◽  
Welding Processes ◽  
Metallurgical Weldability ◽  
Structural Aspects

The study presents technological and structural aspects of production and heat treatment of welded joints of high-strength, abrasion-resistant Hardox 600 steel. As a result of the conducted research, it was found that the use of welding processes for joining this steel leads to the formation of a wide heat-affected zone, characterized by various structures favoring the reduction of abrasion resistance and deterioration of plastic properties, while increasing the susceptibility to brittle fracture. On the basis of the structural and strength characteristics, an effective welding technology for Hardox 600 steel was proposed, as well as the conditions and parameters of post-welding heat treatment, leading to obtaining structures close to a base material in the entire area of the welded joint. Despite the limited high-carbon equivalent CEV of the metallurgical weldability of the tested steel, the tests carried out in laboratory conditions allowed researchers to obtain welded joints characterized by very high strength indexes, corresponding to the base material, while maintaining satisfactory plastic and impact properties.

Microstructure of resistance spot welding of maraging steels

1990 ◽  
Vol 48 (4) ◽  
pp. 900-901
Author(s):  
I. Neuman ◽  
S.F. Dirnfeld ◽  
I. Minkoff
Keyword(s):  
Maraging Steel ◽  
Spot Welding ◽  
Lath Martensite ◽  
Base Material ◽  
Aging Treatment ◽  
High Strength ◽  
Maraging Steels ◽  
Heat Treated ◽  
Current Cycle ◽  
Welding Processes

Experimental work on the spot welding of Maraging Steels revealed a surprisingly low level of strength - both in the as welded and in aged conditions. This appeared unusual since in the welding of these materials by other welding processes (TIG,MIG) the strength level is almost that of the base material. The maraging steel C250 investigated had the composition: 18wt%Ni, 8wt%Co, 5wt%Mo and additions of Al and Ti. It has a nominal tensile strength of 250 KSI. The heat treated structure of maraging steel is lath martensite the final high strength is reached by aging treatment at 485°C for 3-4 hours. During the aging process precipitation takes place of Ni3Mo and Ni3Ti and an ordered solid solution containing Co is formed.Three types of spot welding cycles were investigated: multi-pulse current cycle, bi-pulse cycle and single pulsle cycle. TIG welded samples were also tested for comparison.The microstructure investigations were carried out by SEM and EDS as well as by fractography. For multicycle spot welded maraging C250 (without aging), the dendrites start from the fusion line towards the nugget centre with an epitaxial growth region of various widths, as seen in Figure 1.

scholarly journals Development of laser welding of high strength aluminium alloy 2024-T4 with controlled thermal cycle

2020 ◽  
Vol 326 ◽  
pp. 08005
Author(s):  
Mete Demirorer ◽  
Wojciech Suder ◽  
Supriyo Ganguly ◽  
Simon Hogg ◽  
Hassam Naeem
Keyword(s):  
Laser Beam ◽  
Laser Welding ◽  
Heat Input ◽  
Thermal Cycle ◽  
Laser Beam Welding ◽  
Base Material ◽  
High Strength ◽  
Cooling Rates ◽  
Aa 2024 ◽  
Welding Processes

An innovative process design, to avoid thermal degradation during autogenous fusion welding of high strength AA 2024-T4 alloy, based on laser beam welding, is being developed. A series of instrumented laser welds in 2 mm thick AA 2024-T4 alloys were made with different processing conditions resulting in different thermal profiles and cooling rates. The welds were examined under SEM, TEM and LOM, and subjected to micro-hardness examination. This allowed us to understand the influence of cooling rate, peak temperature, and thermal cycle on the growth of precipitates, and related degradation in the weld and heat affected area, evident as softening. Although laser beam welding allows significant reduction of heat input, and higher cooling rates, as compared to other high heat input welding processes, this was found insufficient to completely supress coarsening of precipitate in HAZ. To understand the required range of thermal cycles, additional dilatometry tests were carried out using the same base material to understand the time-temperature relationship of precipitate formation. The results were used to design a novel laser welding process with enhanced cooling, such as with copper backing bar and cryogenic cooling.

scholarly journals Challenges of Hot Tapping Into a Sour Gas Transmission Line

2000 ◽  
Author(s):  
Ray Goodfellow ◽  
Rory Belanger
Keyword(s):  
Transmission Line ◽  
Operating Conditions ◽  
New Production ◽  
Line Pressure ◽  
Welding Procedure ◽  
Sour Service ◽  
Line Temperature ◽  
Procedure Development ◽  
Design Pressure ◽  
Sour Gas

Chevron Canada Resources recently completed a hot tap on the Simonette high-pressure sour gas transmission line near Grande Prairie, Alberta. The hot tap was required to bring on new production into the Simonette pipeline without shutting in existing production. The hot tap was completed under full line pressure and gas/condenstate flow during the winter with temperatures averaging −20°C. The design pressure of the 12 “ Gr. 359 Cat II pipeline is 9930 kPa and the line operates at 8200 kPa. The gas in the main transmission line is approximately 2% H2S and 4% CO2. The gas being brought on through the 4″ hot tap tie-in was 21% H2S and 5% CO2. At the tie-in point the transmission line temperature was 3°C. Safely welding on the pipeline under these conditions was a considerable technical challenge. In welding sour service lines it is critical that the final weld hardness be below Vickers 248 micro hardness. This can be very difficult to achieve when welding on a line transporting a quenching medium of gas and condensate. In addition, hydrogen charging of the steel from operation in sour service can lead to hydrogen embrittlement during welding. Ludwig & Associates developed the hot tap weld procedure and extensively tested the procedure to ensure that suitable weld microhardness was achievable under pipeline operating conditions. As part of the procedure development the welder who would perform the hot tap was tested repeatedly until he could confidently and successfully complete the weld. During fieldwork, the welding was rigorously monitored to ensure procedural compliance thereby minimizing the possibility of elevated hardness zones within the completed weldment. This paper will detail with the technical development of the hot tap welding procedure and the successful field implementation.

Multiaxial Mechanical Strength of AA-2024-T3 Aluminium Alloy Sheets Joined by Friction Stir Welding Processes

2009 ◽  
Vol 83-86 ◽  
pp. 1243-1250 ◽  
Author(s):  
R.L.L.P. Cerveira ◽  
G. F. Batalha
Keyword(s):  
Friction Stir Welding ◽  
Base Material ◽  
Short Review ◽  
Multiaxial Loading ◽  
Angle Variation ◽  
Friction Stir ◽  
Aa 2024 ◽  
Aeronautical Industry ◽  
Welding Processes ◽  
Joining Process

The aim is to analyze a junction produced by a Friction Stir Welding (FSW) joining process under multiaxial loading, employing a modified Arcan test that allows an angle variation of the loading in order to evaluate the failure of the FSW weldment as compared to the base material. A short review of the earlier studies and relevant theories about the FSW processes and fracture modes I and II under multiaxial loading are presented and were experimentally evaluated for an AA2024-T3 aluminum alloy sheets (t = 1.6 mm) processed by FSW. The results obtained can serve as a basis to compare the junctions made using FSW and conventional joint methods such as rivets (very common practice in the aeronautical industry).

scholarly journals Modelling of hardfacing layers deposition parameters using robust machine learning algorithms

2021 ◽  
Vol 2130 (1) ◽  
pp. 012016
Author(s):  
K Zając ◽  
K Płatek ◽  
P Biskup ◽  
L Łatka
Keyword(s):  
Gas Metal Arc Welding ◽  
Model Performance ◽  
Base Material ◽  
Neural Model ◽  
Machine Learning Algorithms ◽  
Influence Of Process Parameters ◽  
Generic Structure ◽  
Modelling Framework ◽  
Metal Arc Welding ◽  
Welding Processes

Abstract The study presents a data-driven framework for modelling parameters of hardfacing deposits by GMAW using neural models to estimate the influence of process parameters without the need of creating experimental samples of the material and detailed measurements. The process of GAS Metal Arc Welding (GMAW) hardfacing does sometimes create non-homogenous structures in the material not only in deposited material, but also in the heat-affected zone (HAZ) and base material. Those structures are not fully deterministic, so the modelling method should account for this unpredictable component and only learn the generic structure of the hardness of the resulting material. Artificial neural networks (ANN) were used to create a model of the process using only measured samples without any knowledge of equations governing the process. Robust learning was used to decrease the influence of outliers and noise in the measured data on the neural model performance. The proposed method relies on modification of the loss function and several of them are compared and evaluated as an attempt to construct general framework for analysing the hardness as a function of electric current and arc velocity. The proposed method can create robust models of the hardfacing layers deposition or other welding processes and predict the properties of resulting materials even for unseen parameters based on experimental data. This modelling framework is not typically used for metallurgy, and it requires further case studies to verify its generalisability.

Study on Forming Behaviour of Friction Stir Welded Blanks During Single Point Incremental Forming (SPIF) Process

2020 ◽  
Author(s):  
Shalin Marathe ◽  
Harit Raval
Keyword(s):  
Friction Stir Welding ◽  
Incremental Forming ◽  
Single Point ◽  
Base Material ◽  
Forming Limit ◽  
Single Point Incremental Forming ◽  
Cnc Milling ◽  
Forming Process ◽  
Friction Stir ◽  
Welding Processes

Abstract The automobile, transportation and shipbuilding industries are aiming at fuel efficient products. In order to enhance the fuel efficiency, the overall weight of the product should be brought down. This requirement has increased the use of material like aluminium and its alloys. But, it is difficult to weld aluminium using conventional welding processes. This problem can be solved by inventions like friction stir welding (FSW) process. During fabrication of product, FSW joints are subjected to many different processes and forming is one of them. During conventional forming, the formability of the welded blanks is found to be lower than the formability of the parent blank involved in it. One of the major reasons for reduction in formability is the global deformation provided on the blank during forming process. In order to improve the formability of homogeneous blanks, Single Point Incremental Forming (SPIF) is found to be giving excellent results. So, in this work formability of the welded blanks is investigated during the SPIF process. Friction Stir Welding is used to fabricate the welded blanks using AA 6061 T6 as base material. Welded blanks are formed in to truncated cone through SPIF process. CNC milling machine is used as SPIF machine tool to perform the experimental work. In order to avoid direct contact between weld seam and forming tool, a dummy sheet was used between them. As responses forming limit curve (FLC), surface roughness, and thinning are investigated. It was found that use of dummy sheet leads to improve the surface finish of the formed blank. The formability of the blank was found less in comparison to the parent metal involved in it. Uneven distribution of mechanical properties in the welded blanks leads to decrease the formability of the welded blanks.

Sign in / Sign up

Export Citation Format

Share Document