Numerical Simulation of Flow Control on Marine Riser With Attached Splitter Plate

2010 ◽  
Author(s):  
Jiasong Wang ◽  
Hua Liu ◽  
Fei Gu ◽  
Pengliang Zhao
Keyword(s):  
Numerical Simulation ◽  
Flow Control ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Splitter Plate ◽  
Hydrodynamic Characteristics ◽  
Control Effect ◽  
Long Time ◽  
Lift And Drag ◽  
Lift And Drag Coefficient

Attaching a splitter plate (SP) on the base of a riser wall is used to control the flow of risers and evaluated by using the CFD technique in this paper. A finite-volume total variation diminishing (TVD) approach for solving incompressible turbulent flow with renormalization group (RNG) turbulence model was used to simulate the hydrodynamic characteristics of the riser system with additional SP for the different aspect ratio of length to diameter L/D. It was shown that the present numerical method has high order of accuracy by comparing with the available experimental and numerical simulation data for typical circular cylinder flow. A riser system attached with SPs of L/D = 0.5∼2.0 for Reynolds number 1000, and 30000 respectively can obviously reduce the lift and drag coefficient and alter the vortex shedding frequency. The mean drag coefficient can be reduced up to 20% and 35% and the maximum lift coefficient can be reduced up to 94% and 97%, for Re = 1000 and 30000, respectively. The lift can be effectively suppressed after a relative long time. L/D = 0.5∼1.0 may be considered as more practical geometries considering the real conditions, which also have good flow control effect.

Effects of surface flow visualisation on aerodynamic loads at low Reynolds number

2015 ◽  
Vol 119 (1215) ◽  
pp. 663-672
Author(s):  
L. W. Traub ◽  
R. Waghela ◽  
E. M. Botero
Keyword(s):  
Drag Coefficient ◽  
Lift Coefficient ◽  
Time History ◽  
Surface Flow ◽  
Flow Visualisation ◽  
Distribution Method ◽  
History Of ◽  
Low Reynolds ◽  
Lift And Drag ◽  
Lift And Drag Coefficient

AbstractIn this article, the effect of on-surface flow visualisation (SVF) techniques on measured loads over an airfoil are explored. Titanium dioxide based mixture effects on the lift and drag coefficient are experimentally quantified at low Reynolds numbers by recording the time history as the patterns evolve and freeze. With statistical comparison based on Student’s t-distribution method, it was determined that the effect on the drag coefficient was minimal but the lift coefficient was slightly attenuated. Additionally, it was observed that at high angles-of-attack the temporal history of the flow as the wind tunnel ramps up may alter the steady-state flow field in the presence of a SFV mixture.

scholarly journals Numerical Analysis of the Aerodynamic Characteristics of NACA-4312 Airfoil

2020 ◽  
Vol 01 (02) ◽  
pp. 29-36
Author(s):  
Md Rhyhanul Islam Pranto ◽  
Mohammad Ilias Inam
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Turbulence Models ◽  
Aerodynamic Characteristics ◽  
Numerical Results ◽  
Ansys Fluent ◽  
Coefficient Increase ◽  
Lift And Drag ◽  
Lift And Drag Coefficient

The aim of the work is to investigate the aerodynamic characteristics such as lift coefficient, drag coefficient, pressure distribution over a surface of an airfoil of NACA-4312. A commercial software ANSYS Fluent was used for these numerical simulations to calculate the aerodynamic characteristics of 2-D NACA-4312 airfoil at different angles of attack (α) at fixed Reynolds number (Re), equal to 5×10^5 . These simulations were solved using two different turbulence models, one was the Standard k-ε model with enhanced wall treatment and other was the SST k-ω model. Numerical results demonstrate that both models can produce similar results with little deviations. It was observed that both lift and drag coefficient increase at higher angles of attack, however lift coefficient starts to reduce at α =13° which is known as stalling condition. Numerical results also show that flow separations start at rare edge when the angle of attack is higher than 13° due to the reduction of lift coefficient.

Study on the Effects of Active Flow Control on Aerodynamic Performance of Two Airfoils in Tandem Configuration

2017 ◽  
Author(s):  
Ehsan Asgari ◽  
Armin Sheidani ◽  
Mehran Tadjfar
Keyword(s):  
Flow Control ◽  
Drag Coefficient ◽  
Active Flow Control ◽  
Aerodynamic Characteristics ◽  
Primary Objective ◽  
Tandem Configuration ◽  
Drag Forces ◽  
Lift And Drag ◽  
Lift And Drag Coefficient ◽  
Active Flow

Aerodynamic investigation of tandem airfoil configuration has so many applications in different industries that has become a topic of scientific interest since many years ago. One can name a lot of applications in this field such as the aerodynamic interaction between a wing and a tail or a wing and a flap of an aircraft, blades of a rotor and a stator in a compressor or turbine, the tandem blades in the rotor of a compressor, wings of an MAV, to name but a few. The primary objective of this research is to investigate the effect of active flow control (AFC) on two airfoils in tandem configuration, in which the upstream airfoil undergo pitching motion and the downstream airfoil is stationary. In the first place, the aerodynamic characteristics of airfoils in tandem configuration such as lift and drag coefficient is obtained when there is no flow control on the airfoils (clean case). Following this, the mentioned quantities are calculated for the airfoils when AFC has been applied on the forefoil. In order to analyze the effect of AFC and tandem configuration aerodynamic characteristics, the lift and drag coefficient of clean case is compared to those of the controlled case. The result suggests that AFC has caused the amount of CL to grow significantly. It was also observed that the tandem configuration had little influence on the forefoil. On the other hand, the vortices coming from the upstream airfoil generated thrust on the hindfoil. In case of AFC, our results suggest that fluctuations of both lift and drag forces decrease in the hindfoil. It is worth mentioning that this research is among the firsts studying the effect of AFC on tandem airfoils and will pave the way for those who are interested in this field.

Numerical Analysis of Water Suction Effect on Lift and Drag Coefficient of a Hydrofoil With Cavitation

2009 ◽  
Author(s):  
Mohammad J. Izadi
Keyword(s):  
Drag Coefficient ◽  
Mass Flow ◽  
Static Pressure ◽  
Turbulent Viscosity ◽  
Lift Coefficient ◽  
Vapor Bubbles ◽  
Cloud Cavitation ◽  
Lift And Drag ◽  
Lift And Drag Coefficient ◽  
Unsteady Cavitating Flow

Cavitation is the formation of the vapor bubbles within a liquid where the flow dynamics, cause the local static pressure to drop below the vapor pressure. This phenomenon can cause undesirable effects on the hydrofoils such as a decrease in the lift and an increase in the drag. In the present study, the unsteady cavitating flow over a 3-D hydrofoil is numerically simulated. The purpose of this work is to investigate the effect of the upper surface suction in the cavitation area on the lift and drag coefficients of a hydrofoil. An unsteady uniform flow of water over a 3-D NACA hydrofoil is numerically simulated. The full cavitation model along with the RNG k-ε turbulence model is implemented. A modification to the turbulent viscosity, which is necessary to simulate the cloud cavitation, is implemented. The simulation is implemented for various angles of attack and various suction velocities. Comparison between some experimental data and the numerical simulation obtained here is done in order to validate the numerical results. The results obtained here show that, as the mass flow of the water suction increases, the drag coefficient is decreased for large angles of attack, but for small angles of attack it does not change as much. As the mass flow of the water suction increases, the lift coefficient is decreased for small angles of attack and for larger angles of attack the lift coefficient is increased.

scholarly journals Investigations of Lift and Drag Performances on Neo-Ptero Micro UAV Models

2021 ◽  
Vol 84 (2) ◽  
pp. 50-62
Author(s):  
Noor Iswadi Ismail ◽  
Mahamad Hisyam Mahamad Basri ◽  
Hazim Sharudin ◽  
Zurriati Mohd Ali ◽  
Ahmad Aliff Ahmad Shariffuddin ◽  
...  
Keyword(s):  
Wind Tunnel ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Successful Development ◽  
Aerodynamic Efficiency ◽  
Trade Off ◽  
Flight Stability ◽  
Stall Angle ◽  
Lift And Drag ◽  
Lift And Drag Coefficient

This paper presents the investigation and improvement of lift and drag characteristics of Neo-Ptero micro-UAV models based on the virtual wind tunnel method. Despite its successful development and flight stability, the lift and drag coefficients characteristics of the current Mark 1 Neo-Ptero remain unknown. To improve the Mark 1 Neo-Ptero performances, Mark 2 Neo-Ptero model has given a new unsymmetrical airfoil wing configuration. The computational aerodynamic analysis was executed and focused on certain lift and drag coefficient characteristics. Lift coefficient results showed that Mark 2 improved in overall lift characteristics such as zero-lift angle, maximum lift magnitude and stall angle magnitude. Conversely, Mark 2 model suffered a slightly higher drag coefficient magnitude and more significant drag increment percentage than Mark 1. However, the trade-off between superior lift magnitude and minor drag generation induced by Mark 2 boosts the model’s aerodynamic efficiency performances but is only limited at early angle stages.

scholarly journals Research on hydrodynamic characteristics of cylinder planing

2021 ◽  
Vol 39 (1) ◽  
pp. 101-110
Author(s):  
Fuqiang Liu ◽  
Kai Luo ◽  
Hongge Liang ◽  
Chuang Huang ◽  
Shaohang Geng ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Drag Coefficient ◽  
High Speed ◽  
Lift Coefficient ◽  
Hydrodynamic Characteristic ◽  
Calculation Model ◽  
Simulation Software ◽  
Hydrodynamic Characteristics ◽  
Water Splash ◽  
Flow Field Characteristics

This paper selects SST k-w turbulence model and VOF wave to construct a numerical calculation model of moving body planning on a flat free surface based on STAR-CCM+ numerical simulation software. The construction model is checked through foreign classic literature, and the numerical simulation results are in good agreement with the experimental results. The hydrodynamic numerical errors are less than 5%, which is within the engineering error range. The model can be used for the numerical simulation of the planning cylinder. In this paper, it is used to simulate the planing process of cylinder with different speeds and different submerged depths, and the flow field characteristics and hydrodynamic characteristics in the planing process are obtained. The results show that waves appear at the tail and the tail liquid splashes to form a water splash during the planing process of the cylinder on a flat surface. The higher the speed of the planning cylinder is, and the deeper the submersion depth, the more pronounced waves at the tail. When the cylinder has a Fr number Cv≥8, the hydrodynamic force of the cylinder is almost unchanged, and it is not affected by the speed. But when Cv=3, the hydrodynamic characteristic coefficient is higher. The drag coefficient is 20% higher than that in the high-speed (Cv≥8) planing process. The lift coefficient is 3 times of high-speed planing lift coefficient. It is related to the surface pressure and frictional force distribution of cylinder during the low-speed planing. There is a linear relationship between the drag coefficient and the submerged depth during the cylinder planing at different submerged depths.

CFD Computation of Water Injection on Lift and Drag of a Hydrofoil With Cavitation

2009 ◽  
Author(s):  
Mohammad J. Izadi ◽  
Pejman Hazegh Fetratjou
Keyword(s):  
Numerical Simulation ◽  
Drag Coefficient ◽  
Turbulence Model ◽  
Mass Flow ◽  
Bubble Dynamics ◽  
Turbulent Viscosity ◽  
Lift Coefficient ◽  
Water Injection ◽  
Cloud Cavitation ◽  
Lift And Drag

The occurrence of cavitation on hydrofoils can cause undesirable effects such as a decrease in lift, and an increase in drag. The goal of this research is to investigate the effect of water injection on the lift and drag coefficient of a hydrofoil. An unsteady uniform flow of water over a 3-D NACA hydrofoil is numerically simulated. For the numerical simulation of a cavitating flow, a bubble dynamics cavitation model is used to describe the generation and evaporation of the vapor phase. The RNG k-ε turbulence model is used as a turbulence model. A modification to the turbulent viscosity, which is necessary to simulate the cloud cavitation, is implemented. This simulation is implemented for various angles of attack and different injection velocities. Comparison between experimental data and the numerical simulation obtained here is done to validate the numerical results. The results presented show that, as the mass flow of the water injection increases, the lift coefficient decreases for all angles of attack but the rate of this decrease decreases for higher angles of attack. As the mass flow rate increases, the drag coefficient increases more for small angles of attack, and decreases for larger angles of attack, and the injection does not change the drag coefficient as much for large angles of attack. In general, water injection does not increase the lift and does not decrease the drag for all angles of attack.

CFD of Water Injection on Lift and Drag of a 2-D Hydrofoil With Cavitation

2009 ◽  
Author(s):  
Mohammad J. Izadi
Keyword(s):  
Numerical Simulation ◽  
Drag Coefficient ◽  
Turbulence Model ◽  
Mass Flow ◽  
Bubble Dynamics ◽  
Turbulent Viscosity ◽  
Lift Coefficient ◽  
Water Injection ◽  
Cloud Cavitation ◽  
Lift And Drag

Undesirable effects such as a decrease in lift and an increase in drag can be the result of the occurrence of cavitation on hydrofoils. The goal of this research is to investigate the effect of water injection on the lift and drag coefficient of a 2-D hydrofoil. An unsteady uniform flow of water over a NACA hydrofoil (2D) is numerically simulated. For the numerical simulation of a cavitating flow, a bubble dynamics cavitation model is used to describe the generation and evaporation of the vapor phase. The RNG k-ε turbulence model is used as a turbulence model. To simulate the cloud cavitation, a modification to the turbulent viscosity which is necessary, is implemented. This simulation is done for various angles of attack and different injection velocities. Comparison between experimental data and the numerical simulation obtained here is done to validate the numerical results. The results presented here show that, as the mass flow of the water injection increases, the lift coefficient decreases for all angles of attack but the rate of this decrease decreases for higher angles of attack. As the mass flow rate increases, the drag coefficient increases more for small angles of attack and decrease for larger angles of attack.

scholarly journals Near Stall Unsteady Flow Responses to Morphing Flap Deflections

Fluids ◽  
2021 ◽  
Vol 6 (5) ◽  
pp. 180
Author(s):  
Chawki Abdessemed ◽  
Yufeng Yao ◽  
Abdessalem Bouferrouk
Keyword(s):  
Unsteady Flow ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Flow Characteristics ◽  
Time Histories ◽  
Flap Deflection ◽  
Lift And Drag ◽  
Lift And Drag Coefficient ◽  
Static Conditions ◽  
Les Model

The unsteady flow characteristics and responses of an NACA 0012 airfoil fitted with a bio-inspired morphing trailing edge flap (TEF) at near-stall angles of attack (AoA) undergoing downward deflections are investigated at a Reynolds number of 0.62 × 106 near stall. An unsteady geometric parametrization and a dynamic meshing scheme are used to drive the morphing motion. The objective is to determine the susceptibility of near-stall flow to a morphing actuation and the viability of rapid downward flap deflection as a control mechanism, including its effect on transient forces and flow field unsteadiness. The dynamic flow responses to downward deflections are studied for a range of morphing frequencies (at a fixed large amplitude), using a high-fidelity, hybrid RANS-LES model. The time histories of the lift and drag coefficient responses exhibit a proportional relationship between the morphing frequency and the slope of response at which these quantities evolve. Interestingly, an overshoot in the drag coefficient is captured, even in quasi-static conditions, however this is not seen in the lift coefficient. Qualitative analysis confirms that an airfoil in near stall conditions is receptive to morphing TEF deflections, and that some similarities triggering the stall exist between downward morphing TEFs and rapid ramp-up type pitching motions.

Sign in / Sign up

Export Citation Format

Share Document