Effects of Wind on the Heat Flow of FPSO Topsides Subject to Fire: An Experimental and Numerical Study

2010 ◽  
Author(s):  
Joon Young Yoon ◽  
Seong Hwan Kim ◽  
Gwon Cheol Yu ◽  
Jung Kwan Seo ◽  
Bong Ju Kim ◽  
...  
Keyword(s):  
Thermal Diffusion ◽  
Numerical Study ◽  
Wind Tunnel Test ◽  
Experimental Results ◽  
Test Facility ◽  
Test Model ◽  
Cfd Simulations ◽  
Fire Engineering ◽  
Diffusion Characteristics ◽  
Fire Loads

The aim of this paper is to examine the effect of wind on the thermal diffusion characteristics of floating production storage and offloading (FSPO) topside models subject to fire. It is motivated by the need to identify the fire loads on FPSO topsides, taking into account the effects of wind speed and direction. The results of an experimental and numerical study undertaken for these purposes are reported here. This paper is part of Phase II of the joint industry project on explosion and fire engineering of FPSOs (EFEF JIP) [1]. An experiment was performed on a 1/14-scale FPSO topside model using a wind tunnel test facility. The locations of the heat source of the fire were varied, as were the speed and direction of the wind, and the temperature distribution was measured. Computational fluid dynamics (CFD) simulations using the ANSYS CFX program were performed on the test model, with the results obtained compared with the experimental results. It is concluded that wind has a significant effect on the thermal diffusion characteristics of the test model and that the CFD simulations are in good agreement with the experimental results. The insights developed in this study will be very useful for the fire engineering of FPSO topsides.

Test Results on the ARL 19 Supersonic Blade Cascade

1988 ◽  
Vol 110 (4) ◽  
pp. 450-455 ◽  
Author(s):  
A. Fourmaux ◽  
R. Gaillard ◽  
G. Losfeld ◽  
G. Meauze´
Keyword(s):  
Theoretical Analysis ◽  
Data Reduction ◽  
Experimental Results ◽  
Test Facility ◽  
Experimental Program ◽  
Test Model ◽  
Test Results ◽  
Blade Cascade

This paper presents the ONERA contribution in a joint experimental program on the aerodynamics of supersonic airfoil cascades. The first part deals with the specific ONERA way of running cascade tests: description of the test facility, the test model, the instrumentation, and data reduction. Then, after a brief theoretical analysis of the ARL 19 cascade, some experimental results are presented and discussed.

DEVELOPMENT OF A RAPID PROTOTYPING METHODOLOGY FOR WIND TUNNEL TEST MODEL DESIGN

2019 ◽  
Author(s):  
Bruno Ricardo Massucatto Padilha ◽  
Guilherme Barufaldi ◽  
ROBERTO GIL ANNES DA SILVA
Keyword(s):  
Wind Tunnel ◽  
Rapid Prototyping ◽  
Wind Tunnel Test ◽  
Test Model ◽  
Model Design

Load Characteristics of Steel and Concrete Tubular Members Under Jet Fire: An Experimental and Numerical Study

2010 ◽  
Author(s):  
Jeong Hyo Park ◽  
Bong Ju Kim ◽  
Jung Kwan Seo ◽  
Jae Sung Jeong ◽  
Byung Keun Oh ◽  
...  
Keyword(s):  
Cfd Simulation ◽  
Numerical Study ◽  
Fire Load ◽  
Adiabatic Wall ◽  
Fire Engineering ◽  
Ansys Cfx ◽  
Design Values ◽  
Computational Fluid Dynamics Cfd ◽  
Load Characteristics ◽  
Set Up

The aim of this study was to evaluate the load characteristics of steel and concrete tubular members under jet fire, with the motivation to investigate the jet fire load characteristics in FPSO topsides. This paper is part of Phase II of the joint industry project on explosion and fire engineering of FPSOs (EFEF JIP) [1]. To obtain reliable load values, jet fire tests were carried out in parallel with a numerical study. Computational fluid dynamics (CFD) simulation was used to set up an adiabatic wall boundary condition for the jet fire to model the heat transfer mechanism. A concrete tubular member was tested under the assumption that there is no conduction effect from jet fire. A steel tubular member was tested and considered to transfer heat through conduction, convection, and radiation. The temperature distribution, or heat load, was analyzed at specific locations on each type of member. ANSYS CFX [2] and Kameleon FireEx [3] codes were used to obtain similar fire action in the numerical and experimental methods. The results of this study will provide a useful database to determine design values related to jet fire.

Numerical and Experimental Study of Turbulent Flows Around Clark Y-14 Aerofoil

2015 ◽  
Author(s):  
Kshitij Vadake ◽  
Jie Cui
Keyword(s):  
Fluid Dynamics ◽  
Wind Tunnel ◽  
Real World ◽  
Force Measurement ◽  
Test Model ◽  
Wind Tunnel Testing ◽  
Cfd Simulations ◽  
Measurement Device ◽  
Tunnel Testing

Experimental Fluid Dynamics (EFD) and Computational Fluid Dynamics (CFD) have been instrumental in Fluid Mechanics to help solve scientific and engineering problems. This research attempts to use both techniques to perform a parametric study of turbulence flow around airfoil ClarkY-14 at various velocity and angle of attack (AoA). Clark Y-14 airfoil was designed in the 1920’s. It demonstrated good overall performance at low and moderate Reynolds numbers. With the progress in the aviation field, its performance was sub-optimal for newer aircraft designs. However, with the advent of RC airplanes and model aircrafts, there is a renewed interest in this airfoil. Various research projects have been conducted using this airfoil, but there hasn’t been a combined EFD and CFD study of the performance characteristics of the airfoil itself, which still finds real world applications today. One important aspect of this research included the investigation of the effects of a Force Measurement Device/Sensor, which is typically used in scaled/full-size wind tunnels to mount the test model as well as measure the forces/moments acting on it during the testing. The presence of such a device could affect the quality of the data obtained from the wind tunnel testing when compared to a real world application scenario where the aforementioned device may not be present. To the best of the author’s knowledge, no detailed study has been published on the effects of such devices. In this study, the results with and without the measuring device were generated by using CFD simulations. The results were then compared to see to what extent the inclusion of these devices will affect the results. The methodology used for this research was experimental as well as computational. In the present research, a commercially available CFD software STAR-CCM+ was employed to simulate the flows around airfoil Clark Y-14. The experimental data was obtained from wind tunnel tests using AEROLAB Educational Wind Tunnel (EWT) and compared with the simulation data from the CFD. The two data sets were in good agreement. Both experimental and simulation results were used to understand the effects of the measurement device/sensor used in the scaled wind tunnel on the lift and drag coefficients of the airfoil. Two separate CFD simulation setups were designed to model the presence and absence of the measurement device/sensor. These setups replicated the wind tunnel setup. The airfoil was tested and simulated at different speeds as well as different AoA. The comparative study gave a useful insight on the accuracy of the CFD simulations in relation to the actual testing. The analysis of results concluded that the force measurement device/sensor had insignificant effects on the accuracy and quality of data collected through wind tunnel testing.

scholarly journals Contribution of upper airway geometry to convective mixing

2008 ◽  
Vol 105 (6) ◽  
pp. 1733-1740 ◽  
Author(s):  
Santhosh T. Jayaraju ◽  
Manuel Paiva ◽  
Mark Brouns ◽  
Chris Lacor ◽  
Sylvia Verbanck
Keyword(s):  
Three Dimensional ◽  
Upper Airway ◽  
Axial Dispersion ◽  
Half Width ◽  
Experimental Results ◽  
Cfd Simulations ◽  
Flow Rates ◽  
Axial Dispersion Coefficient ◽  
Dispersive Effect ◽  
Flow Directions

We investigated the axial dispersive effect of the upper airway structure (comprising mouth cavity, oropharynx, and trachea) on a traversing aerosol bolus. This was done by means of aerosol bolus experiments on a hollow cast of a realistic upper airway model (UAM) and three-dimensional computational fluid dynamics (CFD) simulations in the same UAM geometry. The experiments showed that 50-ml boluses injected into the UAM dispersed to boluses with a half-width ranging from 80 to 90 ml at the UAM exit, across both flow rates (250, 500 ml/s) and both flow directions (inspiration, expiration). These experimental results imply that the net half-width induced by the UAM typically was 69 ml. Comparison of experimental bolus traces with a one-dimensional Gaussian-derived analytical solution resulted in an axial dispersion coefficient of 200–250 cm2/s, depending on whether the bolus peak and its half-width or the bolus tail needed to be fully accounted for. CFD simulations agreed well with experimental results for inspiratory boluses and were compatible with an axial dispersion of 200 cm2/s. However, for expiratory boluses the CFD simulations showed a very tight bolus peak followed by an elongated tail, in sharp contrast to the expiratory bolus experiments. This indicates that CFD methods that are widely used to predict the fate of aerosols in the human upper airway, where flow is transitional, need to be critically assessed, possibly via aerosol bolus simulations. We conclude that, with all its geometric complexity, the upper airway introduces a relatively mild dispersion on a traversing aerosol bolus for normal breathing flow rates in inspiratory and expiratory flow directions.

Thermal Management of Surface Mount Power Magnetic Components

1999 ◽  
Vol 122 (4) ◽  
pp. 323-327
Author(s):  
G. Refai-Ahmed ◽  
M. M. Yovanovich
Keyword(s):  
Heat Transfer ◽  
Power Loss ◽  
Numerical Study ◽  
Lower Surface ◽  
Experimental Results ◽  
Surface Mount ◽  
Conduction Heat Transfer ◽  
Magnetic Components ◽  
Underfill Material ◽  
Good Agreement

A numerical and experimental study of conduction heat transfer from low power magnetic components with gull wing leads was conducted to determine the effects of distributing the power loss between the core, the winding and the thermal underfill on the thermal resistance. The numerical study was conducted in the power loss ratio range of 0.5⩽PR⩽1.0, where the only active power loss was from the winding at PR=1. In addition, the effect of the thermal underfill material between the substrate and the lower surface of the magnetic package on the thermal performance of the magnetic device was also examined. For comparison, a test was conducted on a magnetic component at PR=1, without thermal underfill. This comparison revealed good agreement between the numerical and experimental results. Finally, a general model was proposed for conduction heat transfer from the surface mount power magnetic packages. The agreement between the model and the experimental results was within 8 percent. [S1043-7398(00)00704-0]

Performance of parking steel column damaged by fire

2019 ◽  
Vol 10 (2) ◽  
pp. 138-154
Author(s):  
Farshid Masoumi ◽  
Ebrahim Farajpourbonab
Keyword(s):  
Cyclic Loading ◽  
Seismic Performance ◽  
Numerical Study ◽  
Mechanical Analysis ◽  
Content Type ◽  
Steel Columns ◽  
Fire Engineering ◽  
Steel Column ◽  
Concrete Coating ◽  
Fire Loading

Purpose The primary purpose of this research was to expand the knowledge base regarding the behavior of steel columns during exposure to fire. This paper presents the numerical study of the effect of heat on the performance of parking steel column in a seven-story steel building under cyclic loading. Design/methodology/approach In this research, the forces and deformations developed during a fire are estimated by using detailed 3D finite-element models. The analyses are in the form of a coupled thermo-mechanical analysis in two types of loading: concurrent loading (fire and cyclic loading) and non-concurrent loading (first fire and then cyclically), and the analyses have been conducted in both states of the fire loading with cooling and without cooling using the ABAQUS software. Further, it was investigated whether, during the fire loading, the specimen was protected by a 3-cm-thick concrete coating and how much it changes the seismic performance. After verification of the specimen with the experimental test results, the column model was investigated under different loading conditions. Findings The result of analyses indicates that the effect of thermal damage on the performance of steel columns, when cooling is happening late, is more than the state in which cooling occurs immediately after the fire. In this paper, thermal–seismic performance of parking steel columns has been specified and the effect of the fire damage has been investigated for the protected steel by concrete coating and to the non-protected steel, under both cooling and non-cooling states. Originality/value This study led to recommendations based on the findings and suggestions for additional work to support performance-based fire engineering. It is clear that predicting force and deformation on steel column during fire is complex and it is affected by many variables. Here in this paper, those variables are examined and proper results have been achieved.

The Impact of Predried Lignite Cofiring With Hard Coal in an Industrial Scale Pulverized Coal Fired Boiler

2018 ◽  
Vol 140 (6) ◽  
Author(s):  
Halina Pawlak-Kruczek ◽  
Robert Lewtak ◽  
Zbigniew Plutecki ◽  
Marcin Baranowski ◽  
Michal Ostrycharczyk ◽  
...  
Keyword(s):  
Combustion Chamber ◽  
Bituminous Coal ◽  
Cfd Simulation ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Industrial Scale ◽  
Hard Coal ◽  
Cfd Simulations ◽  
Reference Case ◽  
The Impact

The paper presents the experimental and numerical study on the behavior and performance of an industrial scale boiler during combustion of pulverized bituminous coal with various shares of predried lignite. The experimental measurements were carried out on a boiler WP120 located in CHP, Opole, Poland. Tests on the boiler were performed during low load operation and the lignite share reached over to 36% by mass. The predried lignite, kept in dedicated separate bunkers, was mixed with bituminous coal just before the coal mills. Computational fluid dynamic (CFD) simulation of a cofiring scenario of lignite with hard coal was also performed. Site measurements have proven that cofiring of a predried lignite is not detrimental to the boiler in terms of its overall efficiency, when compared with a corresponding reference case, with 100% of hard coal. Experiments demonstrated an improvement in the grindability that can be achieved during co-milling of lignite and hard coal in the same mill, for both wet and dry lignite. Moreover, performed tests delivered empirical evidence of the potential of lignite to decrease NOx emissions during cofiring, for both wet and dry lignite. Results of efficiency calculations and temperature measurements in the combustion chamber confirmed the need to predry lignite before cofiring. Performed measurements of temperature distribution in the combustion chamber confirmed trend that could be seen in the results of CFD. CFD simulations were performed for predried lignite and demonstrated flow patterns in the combustion chamber of the boiler, which could prove useful in case of any further improvements in the firing system. CFD simulations reached satisfactory agreement with the site measurements in terms of the prediction of emissions.

Sign in / Sign up

Export Citation Format

Share Document