A study on the temperature profile of bifurcation tunnel fire under natural ventilation

This study simulated a series of bifurcation tunnel fire scenarios using the numerical code to investigate the temperature profile of bifurcation tunnel fire under natural ventilation. The bifurcation tunnel fire scenarios considered three bifurcation angles (30°, 45°, and 60°) and six heat release rates (HRRs) (5, 10, 15, 20, 25, and 30 MW). According to the simulation results, the temperature profile with various HRRs and bifurcation angles was described. Furthermore, the effects of bifurcation angles and HRRs on the maximum temperature under the bifurcation tunnel ceiling and the temperature decay along the longitudinal direction of the branch were investigated. According to the theoretical analysis, two prediction models were proposed. These models can predict a bifurcation tunnel fire’s maximum temperature and longitudinal temperature decay in the branch. The results of this study could be valuable for modelling a bifurcation tunnel fire and benefit the fire engineering design of bifurcation tunnels.

Jet-Niche Technology Influence Potential on the Economic and Operating Parameters of the Fire-Engineering Equipment

The Power engineering is an inseparable part of the contemporary world that has a negative influence on the ecology; in particular it provokes the pollution of atmosphere with such harmful emissions as nitrogen and carbon oxides. Different methods are used to reduce the emission of harmful substances. The efficiency of such methods is increased when these are used in combination and not separately. The recirculation of flue gases and the use of contemporary technologies for municipal boilers, in particular jet-niche technology (JNT) enabled the reduction of NOx and СО emissions to the levels that meet the requirements of European standards simultaneously improving the efficiency of the operation of the fire-engineering facility. The principle of operation of the JNT is based on the formation of the compact stable self-controlled vortex structure and on the interaction system of flammable and oncoming oxidizer flows. This technology enables the operation at minimum recirculation values and it means that all boiler parameters can be retained, in particular starting characteristic, combustion stability and unavailability of vibration modes including a high level of fuel burnout. The obtained research data showed that NОх values were in the range of 80 to 140 mg/m3 when the oxygen content at the furnace inlet was 20% and lower for different boiler systems (DKBR-10, KVGM-6.5, PTVM-50) at CO values close to 50 mg/m2. Hence, the use of the burners of a JNT type enables the reduction of NОхemissions and retains the combustion process efficiency.

Ductile connection to improve the fire performance of bare-steel and composite frames

PurposeIn order to improve the robustness of bare-steel and composite structures in fire, a novel axially and rotationally ductile connection has been proposed in this paper.Design/methodology/approachThe component-based models of the bare-steel ductile connection and composite ductile connection have been proposed and incorporated into the software Vulcan to facilitate global frame analysis for performance-based structural fire engineering design. These component-based models are validated against detailed Abaqus FE models and experiments. A series of 2-D bare-steel frame models and 3-D composite frame models with ductile connections, idealised rigid and pinned connections, have been created using Vulcan to compare the fire performance of ductile connection with other connection types in bare-steel and composite structures.FindingsThe comparison results show that the proposed ductile connection can provide excellent ductility to accommodate the axial deformation of connected beam under fire conditions, thus reducing the axial forces generated in the connection and potentially preventing the premature brittle failure of the connection.Originality/valueCompared with conventional connection types, the proposed ductile connection exhibits considerable deformability, and can potentially enhance the robustness of structures in fire.

Simulation of Possible Fire and Explosion Hazards of Clean Fuel Vehicles in Garages

Clean fuel is advocated to be used for sustainability. The number of liquefied petroleum gas (LPG) and hydrogen vehicles is increasing globally. Explosion hazard is a threat. On the other hand, the use of hydrogen is under consideration in Hong Kong. Explosion hazards of these clean fuel (LPG and hydrogen) vehicles were studied and are compared in this paper. The computational fluid dynamics (CFD) software Flame Acceleration Simulator (FLACS) was used. A car garage with a rolling shutter as its entrance was selected for study. Dispersion of LPG from the leakage source with ignition at a higher position was studied. The same garage was used with a typical hydrogen vehicle leaking 3.4 pounds (1.5 kg) of hydrogen in 100 s, the mass flow rate being equal to 0.015 kgs−1. The hydrogen vehicle used in the simulation has two hydrogen tanks with a combined capacity of 5 kg. The entire tank would be completely vented out in about 333 s. Two scenarios of CFD simulation were carried out. In the first scenario, the rolling shutter was completely closed and the leaked LPG or hydrogen was ignited at 300 s after leakage. The second scenario was conducted with a gap height of 0.3 m under the rolling shutter. Predicted results of explosion pressure and temperature show that appropriate active fire engineering systems are required when servicing these clean fuel vehicles in garages. An appropriate vent in an enclosed space such as the garage is important in reducing explosion hazards.

One-Way Coupling of Fire and Egress Modeling for Realistic Evaluation of Evacuation Process

In the discipline of fire engineering, computational simulation tools are used to evaluate the available safe egress time (ASET) and required safe egress time (RSET) of a building fire. ASET and RSET are often analyzed separately, using computational fluid dynamics (CFD) and crowd dynamics, respectively. Although there are advantages to coupling the ASET and RSET analysis to quantify tenability conditions and reevaluate evacuation time within a building, the coupling process is computationally complex, requiring multiple steps. The coupling setup can be time-consuming, particularly when the results are limited to the modeled scenario. In addition, the procedure is not uniform throughout the industry. This paper presents the successful one-way coupling of CFD and crowd dynamics modeling through a new simplified methodology that captures the impact of fractional effective dose (FED) and reduced visibility from smoke on the individual evacuee’s movement and the human interaction. The simulation tools used were Fire Dynamics Simulator (FDS) and Oasys MassMotion for crowd dynamics. The coupling was carried out with the help of the software development kit of Oasys MassMotion in two different example geometries: an open-plan room and a floor with six rooms and a corridor. The results presented in this paper show that, when comparing an uncoupled and a coupled simulation, the effects of the smoke lead to different crowd density profiles, particularly closer to the exit, which elongates the overall evacuation time. This coupling method can be applied to any geometry because of its flexible and modular framework.

Computer Fire Modeling and the Law: Application to Forensic Fire Engineering Investigations

Computer fire modeling can be a two-edged tool in forensic fire engineering investigations. Professional standards of care recommend that fire modeling’s primary use is in examining multiple hypotheses for a fire as opposed to determining its origin. This paper covers the current acceptable benefits of computer fire models, historical and pending legal case law, and methods to use modeling results within expert reports and testimony. Particular issues reviewed are the use of animations versus simulations, evidentiary guidelines, and authentication using verification and validation studies.